RIOTEC DC9270D User manual

1
Quick Guide
- DC9270D
1
Connect to micro USB port of OTG device
2
3
* Before you use scanner, please switch to "C" for battery
charge for 3~4 hours.
* Under “C mode”, you can raise/lower soft-keyboard
easily. (For USB HID only)
4
DC9270D is with Li-Ion battery inside. When in charging,
please use the original power adaptor of OTG device
(recommend). Through it, it charges both OTG device and
DC9270D internal battery at the same time. When in low
battery (Red LED flashing), please charge it immediately.
LED Indicator Information
Green LED OFF Full charged (Charge mode)
Green LED ON Charging (Charge mode)
Red LED Flashing Low battery (Operation mode)
Attention: Under “Operation mode” please do not charging,
otherwise the OTG device's battery will be charging back to
DC9270D’s battery.
5


The touch sensor area is around the central area. There are 2
button triggers on the right and left side.
Please check the above drawing for your reference.
Installation
Before using scanner, please make sure that the OTG device is
fully charged.
1. Under USB HID interface
** When plugged into OTG device, it will be recognized and
begin to scan the barcode.
2. Under USB Serial interface
** Please install PL-2303 driver into your OTG device first.
PL-2303 driver can be downloaded from Google Play
** Connect scanner to your OTG device, then, you can
know which serial port scanner connects to.
** The data you scan will be sent to serial port and your
APP can get the data from serial port directly.
Suction Cup
PU Glue
(Can be used
repeatedly)
Micro USB
cable (OTG)
Exit Windo
w
Li- Ion Battery
O=Operation mode
C=Charge mode
Indicator (LED)
Button Trigger
Touch Trigger Area
Button Trigger
Indicator
(
LED
)
Char
g
e por
t

2
Reset Configuration to Defaults
If you are unsure of the scanner configuration or have
scanned the incorrect codes, please scan the “Default”
barcode. This will reset the scanner to its factory defaults.
(scan from A1 to A6 for USB HID, B1 for HID)
USB HID USB Serial
A1
B1
A2
A3
A4
A5
A6
Note: Please install PL-2303 driver for USB Serial.
Keyboard Language (For USB HID only)
Scan the appropriate country code as below to program the
keyboard layout for your country or language. As a general
rule, the following characters are supported, but need special
care for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
USA
(Original setting)
Italian
Norway France
Germany Vietnam
Sweden Spain
Denmark
P
ortu
g
al
Switzerland Hun
g
ary
Barcode Configuration Method:
Please follow the below 4 steps to complete the
"Symbologies Enable" or "Symbologies Disable"
1. Start Configuration
2. Choose one of 1D symbologies
3. Enable setting: scan Enable-1, then Enable-2
Disable setting: scan Disable-1, then Disable-2
4. End Configuration
Start
Configuration
1D Symbologies – 1
UPC-A UPC-E
EAN-13
(ISBN/ISSN)
EAN-8
Industrial
2 of 5
Matrix
2 of 5
Enable-1 Disable-1
Enable-2 Disable-2
End
Configuration

3
Barcode Configuration Method:
Please follow the below 4 steps to complete the
"Symbologies Enable" or "Symbologies Disable"
1. Start Configuration
2. Choose one of 1D symbologies
3. Enable setting: scan Enable-1, then Enable-2
Disable setting: scan Disable-1, then Disable-2
4. End Configuration
Start
Configuration
1D Symbologies – 2
Code 93
Code 11
MSI/Plessey
UK/Plessey
Codabar
Code 128
UCC/EAN 128
ISBT 128
1D Symbologies – 3
Code 39
(Code 32)
Interleaved
2 of 5
China Post GS1 DataBar
GS1 DataBar
Limited
GS1 DataBar
Expanded
Enable-1 Disable-1
Enable-2 Disable-2
End
Configuration
 Information in this document is subject to change without notice.
 For more information, please visit:
www.riotec.com.tw
R_180504_01