Watchguard WatchGuard AP327X O-105E Installation instructions

WatchGuard
AP327X
Hardware Guide
AP327X
Outdoor Access Point

About This Guide
Information in this guide is subject to change without notice. Companies, names, and data used in
examples herein are fictitious unless otherwise noted. No part of this guide may be reproduced or
transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express
written permission of WatchGuard Technologies, Inc.
Guide revised: 5/4/2020
Copyright, Trademark, and Patent Information
Copyright © 1998 – 2020 WatchGuard Technologies, Inc. All rights reserved. All trademarks or trade names
mentioned herein, if any, are the property of their respective owners.
Complete copyright, trademark, patent, and licensing information can be found in the Copyright and
Licensing Guide, available online at https://www.watchguard.com/wgrd-help/documentation/overview.
About WatchGuard
WatchGuard® Technologies, Inc. is a global leader in network
security, providing best-in-class Unified Threat Management, Next
Generation Firewall, secure Wi-Fi, and network intelligence
products and services to more than 75,000 customers worldwide.
The company’s mission is to make enterprise-grade security
accessible to companies of all types and sizes through simplicity,
making WatchGuard an ideal solution for Distributed Enterprises
and SMBs. WatchGuard is headquartered in Seattle, Washington,
with offices throughout North America, Europe, Asia Pacific, and
Latin America. To learn more, visit WatchGuard.com.
For additional information, promotions and updates, follow
WatchGuard on Twitter, @WatchGuard on Facebook, or on the
LinkedIn Company page. Also, visit our InfoSec blog, Secplicity,
for real-time information about the latest threats and how to cope
with them at www.secplicity.org.
Address
505 Fifth Avenue South
Suite 500
Seattle, WA 98104
Support
www.watchguard.com/support
U.S. and Canada +877.232.3531
All Other Countries +1.206.521.3575
Sales
U.S. and Canada +1.800.734.9905
All Other Countries +1.206.613.0895
WatchGuard Technologies, Inc. i

Contents
WatchGuard AP327X Hardware Guide 1
Requirements 1
About Your Hardware 2
Hardware Specifications 2
Environmental Requirements 3
Hardware Description 4
Device Connections and Buttons 4
Device Indicators 6
Mounting Instructions 9
Pole Mount Installation 9
Wall Mount Installation 10
Connect the Ground Wire 11
Antenna Installation 12
Connect the AP 13
How to Assemble the Weatherproof Connector 14
How to Disassemble the Weatherproof Connector 15
Ethernet Power Injector (Optional) 16
Notices 18
Safety Notices 18
Product Safety Certification 18
Safety Warning 18
Disclaimer 18
HINWEISE ZUR SICHERHEIT 18
Sicherheitshinweis 19
AVISO DE SEGURIDAD 19
Certificación de seguridad del producto 19
ii WatchGuard Technologies, Inc.

Advertencia de seguridad 19
FCC Certification 20
CE Notice 21
Industry Canada Certification 21
Europe – EU Declaration of Conformity (Wireless) 23
Brasil ANATEL 26
Mexico NOM 26
Japan VCCI Notice (Class B ITE) 26
RoHS Statement 26
WEEE Statement 26
REACH Certificate of Compliance 27
WatchGuard Technologies, Inc. iii

WatchGuard AP327X Hardware Guide
WatchGuard AP327X Hardware Guide
The WatchGuard AP327X is intended for outdoor use and features an IP67 waterproof rating, 2X2 MU-
MIMO 802.11ac Wave 2 capabilities, and dual radios that supports 2.4GHz (802.11b/g/n) and 5GHz
(11a/n/ac) to provide wireless clients with enhanced reliability and performance. Power is provided by any
PoE+ Power over Ethernet) power source.
Requirements
There are two ways you can manage your AP327X:
Total Wi-Fi and Secure Wi-Fi with WatchGuard Wi-Fi Cloud
A powerful cloud-based enterprise wireless management solution for AP configuration, security, and
monitoring.
Basic Wi-Fi with WatchGuard Firebox Gateway Wireless Controller
Local management, configuration, security, and monitoring of APs directly from your WatchGuard
Firebox. The WatchGuard Firebox requires Fireware v12.5 and higher.
WatchGuard Technologies, Inc. 1

About Your Hardware
Hardware Specifications
Chipset Qualcomm QCA IPQ4029 + QCA8075
Processor and RAM Qualcomm IPQ4029-1-583MSP with 512MB RAM and
128MB Flash
IPRating IP67
Radio Type and Frequency Band 2.4 GHz, 802.11b/g/n. Max data rate: 300 Mbps
5 GHz, 802.11a/n/ac. Max data rate: 867 Mbps
Antennas 2 N-Type external antennas 2.4 GHz
2 N-Type external antennas 5 GHz
Diminsions: 7.3” x 0.83” x 0.83” (186.0mm x 21.2mm
x21.2mm)
Weight: 0.35 lbs (0.14 kg) / per pair
* Sold separately
Ethernet Interface 1 x 10/100/1000 Mbps Gigabit Ethernet (LAN1) 802.3at
PoE+ capable
1 x 10/100/1000 Mbps Gigabit Ethernet (LAN2) for wired
extension
Power Interface LAN1 PoE+ (802.3at), 48V
Power Consumption Max: 19W
Min: 11W
Average: 16W
MTBF (Mean Time Between Failures)
Rating
4,544,476 hours at 25°C / 77°F
998,437 hours at 65°C / 149°F
Dimensions 8.42” x 8.42” x 2.66” (213.9mm × 213.9mm × 67.5mm)
Weight 3.95 lbs (1.78 kg)
WatchGuard AP327X Hardware Guide
2 WatchGuard Technologies, Inc.

WatchGuard AP327X Hardware Guide
Environmental Requirements
To safely install your WatchGuard AP, we recommend that you:
nInstall the device indoors or outdoors, preferably under cover
nMake sure the device has adequate clearance for air flow and cooling
Other environmental requirements:
Operating Temperature -40°C to 65°C (-40°F to 149°F)
Operating Humidity 5% to 95% non-condensing
Non-operating
Temperature
-40°C to 70°C (-40°F to 158°F)
Non-operating Humidity 5% to 95%, non-condensing
WatchGuard Technologies, Inc. 3

Hardware Description
Device Connections and Buttons
Ethernet Network Interfaces
LAN1: Standard RJ45 connector that supports link speeds of 10/100/1000 Mbps and 802.3at PoE+
connectivity. You can power the WatchGuard AP327X with a PoE+ connection on the LAN1
interface.
LAN2: Standard RJ45 connector that supports link speeds of 10/100/1000 Mbps. In Wi-Fi Cloud, you
can configure this interface as a wired extension on an SSID. For more information, see the
WatchGuard Wi-Fi Cloud Help .
For APs managed locally by a Gateway Wireless Controller, you can bridge together the LAN ports
on AP models that have two LAN interfaces. This enables you to extend the wired network on the
LAN2 interface. For more information, see the Fireware Help .
WatchGuard AP327X Hardware Guide
4 WatchGuard Technologies, Inc.

WatchGuard AP327X Hardware Guide
Reset Button
Resets the WatchGuard AP to factory-default settings.
nYou must use a Phillips screwdriver to remove the cover screw for the reset button. Use a
paper clip or other small object to press the reset button through the hole.
nPress and hold the reset button for up to 10 seconds until all LEDs go off to indicate that the AP
has rebooted.
WatchGuard Technologies, Inc. 5

Device Indicators
The AP327X has these LED indicators:
WatchGuard AP327X Hardware Guide
6 WatchGuard Technologies, Inc.

WatchGuard AP327X Hardware Guide
Device Indicators in AP Firmware 8.8.1 and Higher
LED Status Description
Power Off Powered off.
Solid Green Powered on.
Flashing Green APcannot connect to Wi-Fi Cloud or the Gateway Wireless
Controller.
Flashing Amber APdid not receive an IP address from the DHCPserver.
LAN1 (PoE) Off No Ethernet link.
Solid Green Network interface is up and connected at 10/100/1000 Mbps.
LAN2 Off No Ethernet link.
Solid Green
(Wi-Fi Cloud
mode)
LAN interface is configured for a wired extension of an SSID.
Solid Green
(Local mode)
Network interface is up and connected at 10/100/1000 Mbps.
2.4 GHz
and
5 GHz
radios
Off 8.8.2 and higher: No SSID enabled on the radio.
8.8.1: Wireless radio is inactive.
Solid Green 8.8.2 and higher: SSID enabled on radio.
8.8.1: Wireless radio is active.
WatchGuard Technologies, Inc. 7

Device Indicators in AP Firmware 8.8.0 and Lower
LED Status Description
Power Solid Green Powered on
Off Powered off
LAN1 (PoE) Solid Green Device connected to LAN1 port at 10/100/1000 Mbps.
Fast Flash Green Did not receive valid IP address from DHCP.
Slow Flash Green Cannot connect to WatchGuard Wi-Fi Cloud.
Intermittent Flash Green Activity on LAN1 port.
Off No Ethernet link.
LAN2 Solid Green Device connected to LAN2 port at 10/100/1000 Mbps.
Flashing Green Activity on LAN2 port.
Off No Ethernet link.
2.4 GHz Solid Green Client connected to 2.4 GHz radio.
Intermittent Flash Green Activity on 2.4 GHz radio.
5 GHz Solid Green Client connected to 5 GHz radio.
Intermittent Flash Green Activity on 5 GHz radio.
WatchGuard AP327X Hardware Guide
8 WatchGuard Technologies, Inc.

WatchGuard AP327X Hardware Guide
Mounting Instructions
Your package includes pole-mount and wall-mount accessories for your AP.
The MAC address and serial number of your AP are printed on a label on the back of the
device. Make sure you record this information before you mount the AP.
Pole Mount Installation
Use the supplied pole-mounting accessories to install the AP327X on a pole.
1. Place the AP on the pole.
2. Insert the clamps in the slots on the AP and wrap around the pole.
3. Fasten the screws and make sure the AP is firmly attached to the pole.
WatchGuard Technologies, Inc. 9

Wall Mount Installation
Use the supplied wall-mounting accessories to install the AP327X on a wall.
1. Use the included stencil to drill holes on the wall for the anchors.
2. Insert the four anchors.
3. Affix the mounting bracket to the wall with the included anchor screws.
4. Attach the AP to the mounting bracket.
5. Insert the mounting screws in the slots of the mounting bracket.
6. Fasten the screws.
WatchGuard AP327X Hardware Guide
10 WatchGuard Technologies, Inc.

WatchGuard AP327X Hardware Guide
Connect the Ground Wire
To make sure your outdoor AP is safely protected from electrical events, we recommend you ground the AP
according to your local regulations.
Use the included screw to attach the ground wire to the ground connector on the back of the AP and to a
nearby grounding point.
WatchGuard Technologies, Inc. 11

Antenna Installation
WatchGuard dual-band omnidirectional dipole antennas (WG9004) are sold separately in packs of two
antennas.
On the top of the AP327X, there are two N-type connectors each for the 2.4 GHz radio and the 5 GHz radio.
Insert the antennas into the connectors and turn clockwise to tighten.
You can use a combination of WatchGuard omnidirectional and other third-party omnidirectional and
directional antennas based on your deployment requirements.
If you use other third-party antenna types, you are responsible for verifying compliance
with regional-based regulations on Equivalent Isotropically Radiated Power (EIRP). The
maximum power output + antenna gain = EIRP. For example, the maximum EIRP
defined by the FCC in the U.S. for 2.4 GHz is 30 dBm (1 Watt), and 5 GHz is 5.15-5.25
23 dBm (200mW), 5.25-5.35 30dBm (1W), and 5.72-5.85 36 dBm (4W).
WatchGuard AP327X Hardware Guide
12 WatchGuard Technologies, Inc.

WatchGuard AP327X Hardware Guide
Connect the AP
To power on and connect the AP327X to the network:
1. Plug one end of an Ethernet cable into the LAN1 (PoE) port on the AP.
Make sure you insert the Ethernet cable correctly through the waterproof assembly before you tighten
the LAN port cap.
2. Plug the other end into a PoE+ (802.3at) compatible switch or PoE+ injector.
WatchGuard Technologies, Inc. 13

How to Assemble the Weatherproof Connector
Use these instructions to connect the Ethernet cable to the AP through the weatherproof connector.
WatchGuard AP327X Hardware Guide
14 WatchGuard Technologies, Inc.

WatchGuard AP327X Hardware Guide
How to Disassemble the Weatherproof Connector
Use these instructions to disconnect the Ethernet cable from the weatherproof connector.
WatchGuard Technologies, Inc. 15

Ethernet Power Injector (Optional)
You can also power the AP327X with an optional Ethernet Power Injector. The PoE+ power injector enables
you to power the AP through an existing Ethernet connection. With this device, you do not have to position
your AP near a power outlet.
This device complies with IEEE 802.3at/af PoE specifications. Do not use any PoE
adapters that are not IEEE 802.3at/af compliant as they may damage your device.
To connect an Ethernet Power Injector to the WatchGuard AP:
1. Plug the Ethernet Power Injector into an AC power source.
2. Connect an Ethernet cable from your network backbone (for example, PoE+ capable router, switch, or
hub) to the LAN connector on the Ethernet Power Injector.
3. Connect an Ethernet cable from the LAN1 (PoE) Ethernet interface on the AP to the PoE connector on
the Ethernet Power Injector.
WatchGuard AP327X Hardware Guide
16 WatchGuard Technologies, Inc.