Water Channel Partners EcoPure ECOP30 User manual

7314971 (Rev. U 2/2/21)
Installation and Operation Manual
Manufactured and warranted by
Water Channel Partners
1890 Woodlane rive
Woodbury, MN 55125
How to install, operate
and maintain your
Reverse Osmosis
rinking Water System
Model ECOP30
System tested and certified by NSF International
against NSF/ANSI Standards 42 & 58. See
performance data on pages 27 & 28 for details.
If you have any questions or concerns when
installing, operating or maintaining your reverse
osmosis system, call our toll free number:
1-800-693-1138
or visit www.ecopure.com
When you call, please be prepared to provide
the model, date code and serial number of your
product, found on the rating decal, located
inside the cover.
PRODUCT REGISTRATION
AND WARRANTY EXTENSION
Please register your product on
www.ecopure.com
See warranty page for
extended warranty details.

2
TABLE OF CONTENTS
Page
Specifications & imensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Unpack and Check Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Plan Your Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Overview & Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17
Step A - Install Supply Water Fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Step B - Install Reverse Osmosis rain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Step C - Install Reverse Osmosis Filter Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Step - Install Storage Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Step E - Install Reverse Osmosis Faucet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13
Step F - Connect Tubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15
Step G - Sanitize, Pressure Test & Purge System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-17
How Your Reverse Osmosis System Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-19
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-21
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-23
Exploded View & Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Performance ata . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-29

3
Supply water pressure limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-100 psi (280-689 kPa)
Supply water temperature limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-100 °F (4-38 °C)
Maximum total dissolved solids (T S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 ppm
Maximum water hardness @ 6.9 pH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 gpg
Maximum iron, manganese, hydrogen sulfide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
Chlorine in water supply (max. ppm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0
Supply water pH limits (pH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Product (quality) water, 24 hours 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.76 gal. (55.9 liters)
Percent rejection of T S, minimum (new membrane) 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86.5
Automatic shutoff control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . yes
Efficiency 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.6 %
Recovery 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.2 %
This system conforms to NSF/ANSI 58 for the specific performance claims as verified and substantiated by test data.
1@ Feed water supply at 50 psi, 77°F, and 750 T S --- Quality water production, amount of waste water and percent rejection
all vary with changes in pressure, temperature and total dissolved solids.
2Efficiency rating means the percentage of the influent water to the system that is available to the user as reverse osmosis treat-
ed water under operating conditions that approximate typical daily usage.
3Recovery rating means the percentage of the influent water to the membrane portion of the system that is available to the user
as reverse osmosis treated water when the system is operated without a storage tank or when the storage tank is bypassed.
Non-potable Water Sources: o not attempt to use this product to make safe drinking water from non-potable water sources.
o not use the system on microbiologically unsafe water, or water of unknown quality without an adequate disinfection before or
after the system. This system is certified for cyst reduction and may be used on disinfected water that may contain filterable
cysts.
Arsenic Reduction: This system shall only be used for arsenic reduction on chlorinated water supplies containing detectable
residual free chlorine at the system inlet. Water systems using an inline chlorinator should provide a one minute chlorine contact
time before the reverse osmosis system.
Nitrate/Nitrite Test it: This system is supplied with a nitrate/nitrite test kit. Product water should be monitored periodically
according to the instructions provided with the test kit.
TDS Test its: T S test kits are available by calling 1-800-949-8220, or check the water testing section of your local phone
directory.
Installations In The Commonwealth Of Massachusetts: The Commonwealth of Massachusetts requires installation be per-
formed by a licensed plumber and do not permit the use of saddle valves. Plumbing code 248--CMR of the Commonwealth of
Massachusetts must be followed in these cases.
Product Water Testing: The Reverse Osmosis System contains a replaceable treatment component critical for the effective
reduction of total dissolved solids. Product water should be tested periodically to verify that the system is performing properly.
Replacement of the reverse osmosis component: This reverse osmosis system contains a replaceable component critical to
the efficiency of the system. Replacement of the reverse osmosis component should be with one of identical specifications, as
defined by the manufacturer, to assure the same efficiency and contaminant performance.
Specifications & Dimensions
11-3/8" 3-1/2"
13"
14"
9" dia.
3-1/2”
13”
14”
11-3/8”
9” dia.
FIG. 1

4
Packing List
Parts Bag
Bag
rain Adapter
Bag
Water Storage Tank
Reverse Osmosis
Assembly
With Red and Yellow
tubes attached
Reverse Osmosis Faucet Assembly
with Black and Blue Tubes
Attached
Green Supply Tube
Tank
Connector
Coin
Battery
Hanger Brackets Eye ropper
NOTE: Codes in the state of Massachusetts require
installation by a licensed plumber and do not per-
mit the use of saddle valves.
If you live in the state of Massachusetts, review
plumbing code 248-CMR of the Commonwealth of
Massachusetts before proceeding with the installa-
tion.
INSPECT SHIPMENT
Your Reverse Osmosis rinking Water System is
shipped complete in one carton. Remove all items from
your shipping carton.
Check all items against the packing list below. Note any
items lost or damaged in shipment. Note any damage
to the shipping carton. Refer to the exploded view and
parts list in the back of the manual for the part names
and numbers of missing or damaged items.
If your new ECOP30 has missing or damaged items,
please call toll free 1-800-693-1138 for free and swift
replacement of missing or damaged items.
If problems exist, refer to the website or the toll free
number listed throughout this manual.
Keep the small parts in the parts bag until you are
ready to install them.
Unpack and Check Your Carton
FIG. 2
Nitrate/Nitrite Test Kit
Water Supply
Fitting

5
TOOLS NEEDED
PLAN YOUR INSTALLATION
Read through the entire manual before beginning
your installation. Follow all steps exactly. Reading this
manual will also help you get all the benefits from your
system.
Your Reverse Osmosis rinking Water System can be
installed under a sink or in a remote location. Typical
remote sites are a laundry room or utility room. Review
the location options below and determine where you are
going to install your system.
NOTE: For best system performance, the feed water
to the system should be softened or have hardness
less than 10 grains per gallon, with no iron.
UNDER THE SIN LOCATION
The Reverse Osmosis Filter Assembly and storage tank
may be installed in a kitchen or bathroom sink cabinet.
See Fig. 4.
A suitable drain point is needed for drain water from the
Reverse Osmosis system.
REMOTE INTERIOR LOCATION
The Reverse Osmosis Filter Assembly and storage tank
may also be installed in a remote interior location away
from the Reverse Osmosis Faucet. You will need a near-
by water source and drain point.
See Fig. 5.
CHEC SPACE REQUIREMENTS
Check size and position of items for proper installation
into location chosen.
TOOLS NEEDED
Review the tools needed list. See Fig. 3. Gather needed
tools before proceeding with the installation. Read and
follow the instructions provided with any tools listed here.
Adjustable wrench
Tape Measure
Phillips Screwdriver
Flathead Screwdriver
rill & rill bits, if required.
Large Adjustable Jaw Pliers or Pipe Wrench
Plan Your Installation
FIG. 3
Questions? Call Toll Free 1-800-693-1138 or visit www.ecopure.com
When you call, please be prepared to provide the model, date code and serial number,
found on the rating decal, located inside the cover.

6
Additional Parts required.
Typical Remote Installation
Hard Water Line
FIG. 5
Outside Faucet
(Hard Water)
Soft, Cold Water
Soft, Hot
Water
Outside Faucet
(Hard Water)
Water
Heater
Shutoff
Valve
Water
Softener
Reverse Osmosis
rain
Soft water
to Reverse
Osmosis
System
Hard
Water to
House
Main
Shutoff
Valve
Storage
Tank
Water
Meter
Reverse Osmosis
System
To Faucet
Floor
rain
Air
Gap
(see
p. 11)
Typical Under Sink Installation
All install parts included in package.
Plan Your Installation
FIG. 4
Storage
Tank
Sink rain P-Trap
Shutoff Valve
Reverse
Osmosis
Assembly
HOT COL
Cold Water
Supply
rain Adapter
for Reverse
Osmosis
Waste Water

7
OVERVIEW
Read through the entire manual before beginning your
installation.
There are seven steps to installing your rinking Water
system. They are as follows:
STEP A - Install Cold Water Supply fitting
STEP B - Install rain Adapter
STEP C - Install Reverse Osmosis Assembly
STEP D - Install Storage Tank
STEP E - Install Reverse Osmosis Faucet
STEP F - Connect Tubing
STEP G - Sanitize, Pressure Test, Purge System
These steps are explained in detail over the next few
pages. Follow all steps. Reading this manual will also help
you receive and use all the benefits your Reverse Osmosis
system can give you.
PREPARE SITE FOR INSTALLATION
1. Before starting, close the hot and cold water shutoff
valves (See Figure 7).
2. Temporarily place tank and filter assembly into planned
location. Check position of items and space required for
proper installation. Ensure tubes may be routed without
kinking.
3. Remove tank and filter from planned location and set
aside.
NOTE: You must check and comply with all local
plumbing codes.
NOTE: Codes in the state of Massachusetts require
installation by a licensed plumber and do not permit
the use of saddle valves.
If you live in the state of Massachusetts, review plumb-
ing code 248-CMR of the Commonwealth of
Massachusetts before proceeding with the installation.
NOTE: For best system performance, the feed water to
the system should be softened or have hardness less
than 10 grains per gallon, with no iron.
FIG. 6
Overview and Site Preparation
Questions? Call Toll Free 1-800-693-1138 or visit www.ecopure.com
When you call, please be prepared to provide the model, date code and serial number,
found on the rating decal, located inside the cover.

8
Step A - Install Supply ater Fitting
Check and comply with local plumbing codes as you plan,
then install a cold feed (supply) water fitting. Refer to the
Specifications page for supply water requirements. The fit-
ting must provide a leak-tight connection to the RO 1/4" tub-
ing. A typical connection using the included water supply fit-
ting is shown in Figure 7.
NOTE: Local code may dictate which type of water fit-
ting is used. Consult a plumber if you are not familiar
with local codes or plumbing procedures.
NOTE: Codes in the state of Massachusetts require
installation by a licensed plumber and do not permit
the use of saddle valves.
If you live in the state of Massachusetts, review plumb-
ing code 248-CMR of the Commonwealth of
Massachusetts before proceeding with the installation.
INSTALL COLD WATER SUPPLY FITTING
(Included)
This fitting will be installed on the cold water pipe. The fit-
ting must provide a leak-tight connection to the Reverse
Osmosis 1/4" tubing. Locate the cold water line in the sink
cabinet. It is recommended, but not required, that the cold
water line be soft water.
Complete the following steps to install the water supply fit-
ting.
1. Close the water shutoff valve (angle stop valve) that the
water supply fitting will be installed on, and open
faucet(s) to relieve pressure.
2. isconnect the existing cold water line from the water
shutoff valve.
3. Make sure that the water supply fitting’s gasket is inside
the female threaded portion of the fitting.
4. Install the water supply fitting onto the cold water shutoff
valve, where the existing cold water line was removed,
and hand tighten. Be careful not to cross thread or over-
tighten.
5. Connect the existing cold water line to the male threaded
portion of the water supply fitting and hand tighten. Be
careful not to cross thread or overtighten.
Cold Water Supply Connection
(included in package)
1/4” green
tubing to
Reverse
Osmosis inlet
FIG. 7
Cold Water
Shutoff Valve
cold water
shutoff
cold water
line
water supply
fitting
gasket

9
Step B - Install RO Drain Under Sink
INTRODUCTION
A suitable drain point is needed for the drain water from
the Reverse Osmosis filter. You have two options:
• Install the Drain Adaptor included with your unit
As shown in Figures 8-10, the drain adaptor is
installed onto your sink’s drain pipe above the P-trap.
This is normally used for under sink installations.
• Use another existing drain in your home
As shown in Figures 11 and 12, the drain tube from
the RO filter runs directly to an open drain. This is
often used for remote location installations.
NOTE: An incorrectly connected drain point can
cause water to leak from the faucet’s air gap.
NOTE: Local code may restrict the type of drain
installation to use. Either drain installation type, if
permitted by code, may be used in under sink or
remote location installations. Consult a plumber if
you are not familiar with plumbing procedures.
INSTALL DRAIN ADAPTOR
(Under sink Installation)
The drain adaptor included with your RO system is
designed to fit around a standard 1-1/2” O. . drain
pipe. In the following procedure, you will install the
drain adaptor above (upstream of) the P-trap. See Fig.
8 & 10. Be sure to comply with local plumbing codes.
NOTE: Before starting this procedure, inspect the
drain pipe under the sink for corrosion, and replace
if necessary, before continuing with installation.
1. Test fit the two halves of the drain adaptor onto the
sink drain pipe, about 6 inches above the P-trap
(See Fig. 9). Make sure that the Q.C. fitting is
toward the direction of the RO faucet (See Fig. 10).
NOTE: Locate so that the drain tubing from the
Reverse Osmosis faucet will run straight to the
adaptor, with no dips, loops, or kinks.
2. Using the hole through the drain fitting as a guide,
mark the pipe where a 3/8” hole will be drilled (See
Fig. 9), and remove the drain adaptor from the pipe.
NOTE: Do not drill through the drain adaptor’s
Q.C. fitting, as this could damage the o-ring.
3. rill a 3/8” dia. hole in the pipe and remove flash.
4. Clean the sink tailpiece to assure a leak-tight fit.
5. Place the halves of the drain fitting back onto the
sink drain pipe. Use a pencil or similar pointed
object to align the Q.C. fitting so that it is centered
on the hole you drilled.
6. Assemble the nuts and screws, as shown in Figure
9, and tighten both sides equally to secure the drain
adaptor halves onto the pipe. o not overtighten.
7. o not connect black tubing to the Q.C. fitting at this
time. It is done after the RO faucet is installed.
FIG. 8
P–Trap
Single Basin
Sink
Double Basin Sink
Under the Sink Installation
rain
Adaptor
rain
Adaptor
Garbage
isposal
FIG. 10
IMPORTANT: Do not install drain adaptor below the P-Trap.
Locate drain adaptor so that when the black
drain tube from the Reverse Osmosis Faucet
is installed it will run straight to the adaptor,
with no dips, loops, or kinks.
Black rain
Tube
P–Trap
rain Adaptor
HOT COLD
FIG. 9
Nuts Sink rain Pipe
Screws
3/8” Quick
Connect
Fitting
rain
Adaptor
Halves
P-Trap
3/8” Hole - Do not drill
through Q.C. Fitting
RO Faucet
P–Trap
Do not install drain
adaptor on a line coming
from a garbage disposal

10
Step B - Install RO Drain In Remote Location
INSTALL A REMOTE DRAIN POINT
AND AIR GAP (Remote Location)
Route the drain tubing to an existing drain in the house.
A floor drain, laundry tub, standpipe, sump, etc. are
suitable drain points. See Fig. 12. This type of drain is
the preferred over the p-trap drain adapter.
Always be sure to provide a 1-1/2” air gap between the
end of the hose and the drain point. This will prevent
water from backing up into the system.
NOTE: Check your local plumbing codes.
To install a remote drain point, complete the
following steps:
1. Locate the 1/4” red tubing on the Reverse Osmosis
filter assembly. See Fig. 11.
2. etermine if this length is long enough to reach the
drain point. Longer lengths of tubing (see parts list in
back of manual) may be needed.
3. If longer tubing is required, disconnect the 1/4” red
tubing and replace with an adequate length of tubing
to reach the drain point. Refer to Step F later in the
manual on how to disconnect and connect tubing.
NOTE: A flow control insert is located inside the
elbow fitting that the drain tube connects to.
Refer to Fig. 29. Leave this fitting in place.
4. Route the tubing to the drain point and secure at the
end with a bracket (not included). See Fig. 12.
Provide a 1-1/2” air gap between the end of the tube
and the drain. See Fig. 12.
Remote Location
Installation
FIG. 11
FIG. 12
Outside Faucet
(Hard Water)
Soft, Cold Water
Soft, Hot
Water
Outside Faucet
(Hard Water)
Water
Heater
Shutoff
Valve
Hard Water Line
Water
Softener
Soft water
to Reverse
Osmosis
System
Hard
Water to
House
Main Shutoff
Valve
Storage Tank
Water
Meter
Reverse Osmosis
System
BLUE Tubing
to Reverse
Osmosis Faucet
GREEN Tubing
to Reverse
Osmosis System
YELLOW Tubing
to Storage Tank
Reverse Osmosis
rain - RE
Tubing to rain
RED
Tubing to
Drain
1/4'' RED Tubing
Floor
Drain
1-1/2”
Air Gap
1-1/2”
Air Gap
1-1/2”
Air Gap
1-1/2”
Air Gap
Sump
Laundry
Tub
Stand pipe

11
Step C: Install RO Filter Assembly
9''
FIG. 13
Screw (2)
15-1/2'' minimum up
from floor. This allows
space to remove and
change filters
Hanger
Washer (2)
Step D - Install Storage Tank
FIG. 14
Tank
Nipple
Storage
Tank
Tubing Nut
Tubing Insert
Tubing Connector
The fitting on the supply tank may need to be tight-
ened 7-8 full turns to get a good seal.
Do not overtighten.
INSTALL STORAGE TAN
1. Apply thread sealing tape (2 wraps clockwise) to
the threads on the nipple at the top of the tank. See
Fig 14.
2. Locate the tubing connector. See Fig. 14. Tighten
the tubing connector onto the tank nipple 7-8 full
turns, being careful not to cross thread or overtighten.
3. o not connect the tube at this time. This will occur
later in the assembly.
4. Place the storage tank next to the Reverse Osmosis
Assembly. The tank can be placed upright or on its
side.
INSTALL REVERSE OSMOSIS FILTER
ASSEMBLY
The Reverse Osmosis Filter Assembly is mounted on
hanger washers.
See Fig 13. The hanger washers allow you to lift the
filter assembly from the washers without any hardware
removal. When planning your installation, you need to
leave room for changing filters.
Complete the following steps to install your Reverse
Osmosis Filter Assembly:
1. Remove the cover.
2. Locate mounting slots on back inside of the assem-
bly. See Fig 13.
3. Hold the assembly up to the wall surface and mark
locations for the hanger washers. See Fig 13. Mount
the unit high enough to allow room to change filters
without taking the unit off of the wall.
4. Fasten the hanger washers to the wall using the
screws provided.
5. Hang assembly on washers.
6. Replace cover.

12
Step E - Install RO Faucet
You will need to select the location of the Reverse
Osmosis Faucet. You have three options to choose
from:
• Use the existing sink top hole for the spray hose
or soap dispenser (Must be 1-1/4” in diameter)
• Drill a new hole in the sink
• Drill a new hole in the countertop next to the
sink
1. etermine where you are going to install your
Reverse Osmosis Faucet.
2. Check to ensure the Reverse Osmosis faucet will
mount flat against the mounting surface.
3. Visually review the routing of the tubes from the
Reverse Osmosis filter assembly to the faucet.
Check to ensure there is adequate tube routing
space between the faucet and filter assembly.
4. If drilling is needed, drill a 1-1/4" diameter hole in
the mounting surface.
IM ORTANT: Drilling holes into countertops and
sinks should only be performed by an installer
who is qualified for drilling such materials.
Drilling of surfaces made of stone or solid sur-
face materials such as granite, marble, Corian™
or other plastic resin products or sinks made of
porcelain or stainless steel may cause perma-
nent, irreparable damage to the sink or counter-
top surface.
FIG. 15
SELECT LOCATION OF REVERSE OSMOSIS
FAUCET MOUNTING HOLE
Questions? Call Toll Free 1-800-693-1138 or visit www.ecopure.com
When you call, please be prepared to provide the model, date code and serial number,
found on the rating decal, located inside the cover.

13
Step E - Install RO Faucet (cont.)
INSTALL REVERSE OSMOSIS FAUCET
1. Locate and organize your RO faucet install parts. Refer to
Fig. 16.
2. Mount faucet base to sink hole until the faucet base is flat
against the sink surface. The rubber gasket should be
between the sink surface and the faucet base.
3. Tighten the toggle bolts until the base is firmly mounted to
the sink surface. o not overtighten.
4. Locate the faucet body. (The black and blue tubes are
already connected to the faucet.) Insert these tubes into
the sink hole until approximately one foot of tube length
and the faucet body are left above the counter surface.
o not kink the tubes in the process. See Fig. 15.
NOTE: If you routed the red drain tubing directly to a
remote drain point (see page 10), disregard step 5 and
move on to step 6.
5. Locate the 1/4" red tubing. One end is connected to the
RO filter assembly. See Fig 24.
A. Route the loose end of the red tube through countertop
to faucet.
B. Cut the loose end of the red tube square and to length.
See Fig. 19 for tube cutting instructions.
NOTE: Tubing lengths should allow for the removal of
the assembly from the hanger washers for servicing. If
tubing lengths are shortened for neater appearance, it
may be necessary to keep the assembly on the hanger
washers for service.
C. Insert all the way onto the 1/4" faucet barb fitting on
faucet. See Figs. 17, 20 & 21.
D. Pull on the tubing to be sure it is held firmly in the fit-
ting.
6. Mount the faucet body onto the faucet base, 1/4 turn.
FAUCET ELECTRONICS
Inside the faucet base is a battery operated 6 month timer.
An amber LE indicator is also located in the front of the
faucet base. This LE will flash continuously after 6 months
has passed. This indicates that it is time to replace the
battery, prefilter and postfilter.
INSTALLBATTERY
To install battery, complete the following steps.
1. Remove the screw on the right side of the faucet base.
2. Press the battery housing upward from the front faucet
base until it releases from the faucet base. See Fig. 16.
3. Install the battery (CR 2032 or equivalent). Place battery
into the holder with the positive (+) side facing the back of
the holder.
4. When the battery is installed the LE will flash six times
and turn off. This indicates the battery is fully charged.
After the six flashes, the timer enters the 6 month time
cycle.
NOTE: If the LED repeatedly flashes two times, the
battery needs to be replaced.
5. Re-install the battery housing and firmly tighten the
mounting screw. See Fig. 16.
FIG. 16
FIG. 17
BLUE TUBE
3/8” quick connect
fitting for the blue tube
BLAC TUBE
3/8” barb fitting
for the black tube
RED TUBE
1/4” barb fitting
for the red tube
Battery
Housing
Battery,
negative (–)
side facing
the front
Faucet
Base Screw
Toggle Bolts
Rubber
Gasket
Faucet
Base
Screw holding
the battery
housing in place
Amber LE
Timer
Housing Faucet
Body

14
Step F - Connect Tubes
HOW TO CUT AND CONNECT THE TUBES
Your Reverse Osmosis system includes push-in fittings
for quick tubing connection. Review the following
instructions before connecting the tubes in the next
step. Failure to follow these instructions may lead to
future leaks.
Cut tubes to length
1. Use a sharp cutter or knife to cut the end of tubing.
Always cut the tubing square. See Fig. 19.
2. Inspect the tube up to 1” from the end to be sure
there are no nicks, scratches or other rough spots. If
needed, cut the tubing again. See Fig. 19.
NOTE: Tubing lengths should allow for the
removal of the assembly from the hanger wash-
ers for servicing. If tubing lengths are shortened
for neater appearance, it may be necessary to
keep the assembly on the hanger washers for
service.
Connect tubes
NOTE: Remove protective foam plugs before con-
necting tubes (See Fig. 18). Discard foam plugs.
1. Push tubing through collet, until it engages the o-
ring. See Fig. 20. Continue pushing until the tube
bottoms out against the back of the fitting. See Fig.
21. o not stop pushing when the tube engages the
o-ring. Failure to follow these instructions may lead
to future leaks. When a 1/4” tube is fully engaged,
11/16” of the tube has entered the fitting. When a
3/8” tube is fully engaged, 3/4” of the tube has
entered the fitting. Mark tube with a piece of tape or
marker. See Figs. 20 & 21.
2. If additional tubing is required, see parts list at the
end of this manual.
To Disconnect Tubes
1. Push the collet inward with a finger tip. See Fig.23.
2. Continue holding collet inward while pulling the tub-
ing out. See Fig. 23.
Push-in Fitting
Foam Plug
Remove and Discard Foam Plugs FIG. 18
Push-in Fitting
Tube
Tube Correctly Cut FIG. 19
Cut tubing square with end of tubing round,
smooth, with no cuts, nicks or flat spots.
Tube Partially Engaged with Fitting FIG. 20
Collet O-Ring
Tube Fully Engaged with Fitting FIG. 21
Collet O-Ring
Collet and O-Ring FIG. 22
Collet
Fitting
O-Ring Seal
Disconnect Tubing FIG. 23
Tubing
Collet (depress to
remove tubing)

15
Step F - Connect Tubes (cont.)
ROUTE YELLOW TUBE TO STORAGE TAN
1. Locate the yellow tube attached to the Reverse Osmosis
filter assembly.
2. Route the loose end of the yellow tube to the fitting on top
of the storage tank. See Fig. 24.
3. Cut tube square and to length. See Fig. 19.
4. o not connect at this time. This will occur in the sanitizing
step.
CONNECT GREEN TUBE TO COLD WATER
SUPPLY PIPE
1. Route one end of the 1/4” green tube to the fitting on the
water supply pipe. See Fig. 24.
2. Cut tube square and to length. See Fig. 19.
3. Connect to tee feed adaptor. See Fig. 7. Insert all the way
into the fitting. See Figs. 20 & 21.
4. Route the other end of the green tube to green collet to the
fitting on the left side of the Reverse Osmosis filter
assembly.
5. Cut tube square and to length. See Fig. 19.
6. Insert all the way into the fitting. See Figs. 20 & 21.
7. Pull on the tube to be sure it is held firmly in the fitting.
CONNECT BLUE TUBE TO REVERSE OSMOSIS
ASSEMBLY
1. Locate the blue tube attached to the faucet.
2. Route the loose end of the 3/8" blue tube to the blue collet
on the right side of the Reverse Osmosis filter assembly.
3. Cut tube square and to length. See Fig. 19.
4. Insert all the way into the fitting. See Figs. 20 & 21.
5. Pull on the tube to be sure it's held firmly in the fitting.
CONNECT BLAC TUBE FROM REVERSE
OSMOSIS FAUCET TO DRAIN ADAPTER
1. Locate the 3/8" black tube attached to the faucet. Fig. 24.
2. The loose end needs to be attached to the quick connect
fitting on the sink drain adapter.
3. Cut this tube as needed to route it as straight as possible,
without loops, dips, or kinks.
4. Cut the end of the tube square. See Fig. 19.
5. Insert all the way into the fitting. See Figs. 20 & 21.
6. Pull on the tube to be sure it is held firmly in the fitting.
RED TUBE TO REVERSE OSMOSIS FAUCET
The red tube connection was completed in the faucet
assembly steps.
NOTE: Tubing lengths should allow for the
removal of the assembly from the hanger
washers for servicing. If tubing lengths are
shortened for neater appearance, it may be
necessary to keep the assembly on the
hanger washers for service.
NOTE: Codes in the state of Massachusetts
require installation by a licensed plumber
and do not permit the use of saddle valves.
If you live in the state of Massachusetts,
review plumbing code 248-CMR of the
Commonwealth of Massachusetts before
proceeding with the installation.
NOTE: Tube colors
match collet colors.
Tube Connections FIG. 24
Tubing Connector
Sink
P–Trap
3/8” BLUE
1/4” RE
3/8” YELLOW
1/4” GREEN
HOT COL
Water Supply
Fitting
rain
Adaptor
3/8” BLACK
Tubing

16
Step G - Sanitize, Test and Purge System
SANITIZE THE SYSTEM
Sanitizing is recommended immediately after installa-
tion of the Reverse Osmosis system. It’s also recom-
mended after servicing inner parts. It is important that
the person installing or servicing the system have
clean hands while handling inner parts of the system.
Complete the following steps to sanitize the system.
See Fig. 25.
1. Make sure that the water supply to the Reverse
Osmosis system is off.
2. Open the Reverse Osmosis faucet. If the tank is
not already empty, allow the water to empty.
3. Locate the eyedropper included in parts bag and
common household bleach (5.25%).
4. Add 3 ml. of bleach into open end of yellow tubing.
Handle bleach according to bleach manufacturer’s
recommendations. See Fig. 25.
5. Connect yellow tubing to tank connector. See Figs.
14 and 25.
6. Sanitizing the system will be completed during the
pressure test and purging steps on the following
page.
NOTE: The bleach must be removed from the
system before drinking the water. See purging
instructions on the next page.
FIG. 25
RO Sanitization
Cartridge
Postfilter
Sanitization
Cartridge
Prefilter
Sanitization
Cartridge
This reusable sanitizing kit (not included) is
recommended to easily and completely sani-
tize your Reverse Osmosis system annually.
The kit includes the following:
= Prefilter sanitization cartridge
(contains no filtration media)
= Postfilter sanitization cartridge
(contains no filtration media)
= RO sanitization cartridge
(contains no RO membrane)
= Syringe, 1 oz.
= Complete instructions
Uses standard 5.25% household bleach (not
included) to completely sanitize the Reverse
Osmosis system.
Manufacturer recommends using the
Model 7301203 Sanitizing Kit
To order, go to
www.ecopure.com
and click on the “Replacement Parts” link under the “Owner Center” tab,
or call toll free 1-800-693-1138

17
Step G - Sanitize, Test and Purge System (cont.)
PRESSURE TEST THE SYSTEM
NOTE: Complete the sanitizing procedures on the
preceding page before pressure testing.
To pressure test the system, complete the following
steps.
1. Open the water supply valve to the Reverse
Osmosis system.
2. Purge air from the house plumbing by opening sev-
eral house faucets. Close faucets when water runs
smooth, with no spurting.
3. Pressure will start to build in the RO system. In
about 2 hours check all fittings and connections.
Check for water leaks. Fix leaks if any are found. If
problems exist, refer to the troubleshooting chart or
call the toll free number below).
NOTE: When the system is first pressurized, water
may ''spurt'' from the faucet air gap hole until air is
expelled from the RO system.
Please review the following operating features
before using your Reverse Osmosis system:
NOTE: As with all other water system applications,
leaks may occur. Because the system pressure
builds slowly, leaks may not be immediately appar-
ent. Recheck for leaks 24 hours after purging the
system is complete.
NOTE: Codes in the state of Massachusetts require
installation by a licensed plumber and do not per-
mit the use of saddle valves.
If you live in the state of Massachusetts, review
plumbing code 248-CMR of the Commonwealth of
Massachusetts before proceeding with the installa-
tion.
PURGING THE SYSTEM
To purge the system, complete the following steps.
1. Open the Reverse Osmosis Faucet and let water
flow through the system for a 24 hour period. Water
flow will be a slow trickle at this time.
NOTE: Do not consume water from the RO sys-
tem until purging is complete.
2. Close the Reverse Osmosis faucet after the 24 hour
purging period is complete.
3. When the purging is finished, your Reverse
Osmosis system is ready for use.
You will not have filtered water immediately. It may
take several hours to fill the storage tank and create
maximum flow from the Reverse Osmosis faucet.
Water will run to the drain while the Reverse
Osmosis system is producing water, even if you are
not drawing water from the Reverse Osmosis faucet.
You may hear a small quantity of water going to the
drain at times when water is not being used. This is
normal. Water going to the drain will automatically
shut off when the storage tank is full.
Water Pressure from the Reverse Osmosis faucet will
be less than your standard faucet.
FIG. 26
Storage
Tank
Water Supply Shutoff
Valve to Reverse
Osmosis System
HOT COL
Reverse
Osmosis
Faucet
Kitchen
Faucet
Cold Water
Supply

18
How Your RO ater System orks
HOW YOUR REVERSE OSMOSIS SYSTEM
WOR S
Introduction: Your Reverse Osmosis (RO) rinking
Water System uses your household water pressure to
force water through three filters. Minerals and impuri-
ties are filtered out. elicious tasting drinking water
goes to the storage tank-ready for your use. Minerals
and impurities are sent down the drain. The following
paragraphs will explain in detail how your Reverse
Osmosis rinking Water System works.
Prefilter: Water from the cold supply pipe enters the
prefilter. See Fig. 27. The prefilter is a replaceable
sediment cartridge with activated carbon in its compo-
sition. The cartridge reduces taste, odor, sand, silt,
dirt, other sediments, and up to the amount of chlorine
shown in the specifications.
Reverse Osmosis Cartridge: Filtered water flows
from the prefilter to the Reverse Osmosis membrane
cartridge. See Fig. 27. The Reverse Osmosis cartridge
is a tightly wound special membrane. The membrane
reduces the dissolved solids and organic matter. High
quality product water (about one ounce per minute)
exits the Reverse Osmosis cartridge. The product
water flows to the storage tank, postfilter or Reverse
Osmosis faucet. rain water, with the dissolved solids
and organic matter, is routed to the drain.
Storage Tank: The storage tank holds product water.
See Fig. 27. A diaphragm inside the tank holds water
pressurized to about half of supply water pressure
when the tank is full. This provides fast flow to the
Reverse Osmosis faucet. When the tank is empty of
water, the pressure at the air valve is 5 - 7 psi.
Postfilter: Water goes through the postfilter before
going to the Reverse Osmosis faucet. See Fig. 27.
The postfilter is an activated carbon type filter. Any
remaining tastes and odors are reduced from the
product water. Clean, high quality drinking water is
available at the faucet.
Reverse Osmosis Faucet: The sink or countertop
faucet has a hand operated knob to dispense drinking
water. See Fig. 27. An air-gap is built into the faucet
drain water connection to comply with plumbing
codes.
Faucet Electronics: Inside the faucet base is a bat-
tery operated 6 month timer. See Fig. 16.
An amber LE indicator is located in the front of the
faucet base. This LE will flash continuously after
6 months have passed. This indicates that it is time to
replace the battery, prefilter and postfilter.
Shutoff Assembly: The unit has an automatic shutoff
system to conserve water. When the storage tank has
filled to capacity, and the drinking water faucet is
closed, pressure closes the shutoff to stop flow to the
drain. After enough drinking water is used, pressure in
the system drops, and the shutoff opens to allow the
tank to be refilled. See Fig. 27.
Check Valve: A check valve is located in the Reverse
Osmosis manifold above the center cartridge. The
check valve prevents a backward flow of product
water from the storage tank to drain. A backward flow
could damage the Reverse Osmosis Membrane.
See Fig. 27.
Flow Control: Water flow to the drain is restricted by
the flow control. It maintains the desired flow rate to
obtain the highest quality drinking water. The flow con-
trol is located inside the elbow fitting on the Reverse
Osmosis manifold drain port. See Fig. 27.
Questions? Call Toll Free 1-800-693-1138 or visit www.ecopure.com
When you call, please be prepared to provide the model, date code and serial number,
found on the rating decal, located inside the cover.

19
How Your RO ater System orks
Water Flow Description
1. Water enters prefilter. Sand, silt and other sediments are reduced. Chlorine is also reduced. See Fig. 27.
2. Water leaves prefilter and proceeds to the Reverse Osmosis Cartridge.
3. Water enters the Reverse Osmosis membrane. issolved solids are reduced.
4. Processed water leaves the Reverse Osmosis Membrane and flows to the storage tank.
5. rain water with dissolved solids leaves the Reverse Osmosis membrane and flows to the drain.
6. Faucet is activated.
7. Processed water leaves the storage tank and flows to the postfilter, where it is filtered to ensure fresh taste.
8. Water flows to the Reverse Osmosis faucet.
1
34
5
6
7
8
Reverse Osmosis Water Flow Schematic FIG. 27
PRO UCT WATER
Air Gap
PRO UCT
WATER FAUCET
RAIN WATER
WATER
IN
Gravity
rain
BLACK
BLUE
GREEN
RE YELLOW
PREFILTER POSTFILTER
Check
Valve
rain Flow
Control
AUTOMATIC
SHUTOFF
RO
MEMBRANE
PRO UCT
WATER
STORAGE
2

20
FIG. 28
Cover
Prefilter
Cartridge
Manifold
Postfilter
Cartridge
RO
Cartridge
Turn to the left
to remove
Maintenance
PREFILTER / POSTFILTER MAINTENANCE
NOTE: It is recommended to replace the battery,
prefilter and postfilter cartridges at least every 6
months of product water use. Replace more often
if they begin to plug with sediment.
The prefilter and postfilter are replaceable sediment
cartridges with activated carbon in their composition.
See Fig. 28. You must periodically replace the prefilter
and postfilter cartridge. This will protect the RO mem-
brane from being destroyed by chlorine. It will also pre-
vent the filters from plugging with sediment.
You may notice a slower output of product water as
the prefilter and postfilter build up with sediment.
Replace the prefilter and postfilter cartridges when this
occurs. You should replace the battery whenever you
replace the cartridges.
RO MEMBRANE CARTRIDGE MAINTENANCE
The Reverse Osmosis cartridge is a tightly wound spe-
cial membrane. See Fig. 28. The membrane reduces
the dissolved solids and organic matter. The life of the
Reverse Osmosis membrane cartridge depends mostly
on the pH and hardness of the supply water (see
Specifications). Cartridge life is shorter with higher pH.
For example, if supply water pH is from 6.8 to 7.7, the
cartridge may last for well over one year. However,
cartridge life may be as short as 6 months if the pH is
as high as 8.5 to 10. Higher pH weakens the cartridge
membrane and causes pin-hole leaks. It's time to
replace the Reverse Osmosis cartridge when the pro-
duction rate and/or quality of product water drops.
Product water may begin to taste different, indicating
solids and organics are passing through the Reverse
Osmosis membrane. See Reverse Osmosis cartridge
replacement.
REVERSE OSMOSIS CARTRIDGE REPLACE-
MENT
Complete the following steps to replace the cartridges.
NOTE: Do not remove manifold from mounts.
Flexing or twisting may damage the manifold.
1. Remove (turn to the left) the prefilter cartridge from
the manifold to stop flow to the Reverse Osmosis
cartridge.
2. Remove the Reverse Osmosis cartridge.
3. Remove the postfilter cartridge.
4. iscard the cartridges in a proper manner.
5. Install new cartridges in reverse order (post filter,
Reverse Osmosis and then prefilter). Turn cartridges
to the right to reattach to the filter heads. o not
overtighten.
6. Remove and replace the timer battery. See page 13.
7. Purge the Reverse Osmosis system. See page 17
for instructions.
PREFILTER / POSTFILTER CARTRIDGE
REPLACEMENT
Complete the following steps to replace the cartridges.
NOTE: Do not remove manifold from mounts.
Flexing or twisting may damage the manifold.
1. Remove the prefilter cartridge (turn to the left) from
the filter head. Then remove the postfilter cartridge.
2. iscard the cartridges in a proper manner.
3. Install new cartridges in reverse order (postfilter
first, then prefilter). Turn cartridges to the right to re-
attach to the filter heads. o not overtighten.
4. Remove and replace the timer battery. See page 13.
5. Purge the Reverse Osmosis system. See page 17
for instructions.