Watercool HEATKILLER GPU-X3 GTX 560 User manual

Assembly instructions
HEATKILLER® GPU-X³GTX 560
The unique design of the HEATKILLER® GPU-X³ guarantees outstanding performance. A cooling performance in
the range of current high-end CPU coolers, a flat design as well as top quality materials distinguish the new GPU-
X³ series.
The bottom plate consists of pure copper. The cooling structure of the GPU is extremely fine-tuned and offers a
higher performance than most CPU coolers. The thin base ensures even more performance.
HEATKILLER® GPU-X³GTX 560
Dimensions (LxWxH) 158.0 x 117.0 x 11.5mm
Weight 680g
Material (bottom/cover) CU / VA
Connections G ¼ inch
Temperature-resistant up to 80°C
Compatible with Nvidia GeForce GTX560
Note: You will find coloured assembly instructions in PDF format in the service area of our homepage.
(www.watercool.de)
Attention: The Watercool company assumes no liability for any damages caused to hardware. If
uncertain hire a specialist to carry out the modification, or use our modification service. By
disassembling the original cooler you may cause the manufacturer´s warranty to become void, if
uncertain contact the manufacturer of the Graphic card.
Preparation of the Graphic card
Remove the original heatsink and all remnants of the thermal pads.
Place the pre-cut pads on the graphics card as illustrated. Normally, both sides of the pads are covered with a
protective film which must be removed before the installation.
Make sure to place the pads on the right components.
No. 1 – thermal pad 0.25mm height (color light grey)
No. 2 – thermal pad 1.00mm height (color light blue)
Instead of the thermal pads, you can use a non-conductive thermal compound on the RAM components, which
slightly increases the cooling capacity in this area. However, we recommend using the enclosed heat conducting
pads.
Apply the thermal compound to the GPU area evenly.

Assembly of the cooler
The cooler is placed on the prepared graphics board. Then turn the board around together with the cooler. 7 x
M3x8mm screws as well as plastic washers are enclosed with the cooler.
Screw the screws – with washers – into the cooler beginning with the GPU area.
Do not tighten the screws yet!
Once all screws are attached to the cooler, screw them tight beginning with the GPU area. Make sure to tighten
the screws crosswise.
Installation and leak test
After the installation, a check and test run must be performed! The coolers are constructed on the reference
design, still, all sections of the board have to be checked for possible contact to the cooler. In addition, the contact
of the GPU to the cooler must be checked along with the bending of the board. A slight bending of the board is
normal.
A leak test should preferably be performed outside of the computer. If this is not possible, the hardware may not
be turned on during the test run!
Once all of the cooler elements were tested, the computer can be put into operation. Check the temperature of
the GPU immediately after the start!
General information
The HEATKILLER® GPU-X³ GTX560 does not have a defined input and output. The cooling medium can stream
in or our on both sides.
Under normal circumstances it is not necessary to open the cooler. If you still want to do so, please use a
corresponding tool for Allen screws in industrial quality.
We recommend using demineralised or deionised water (distilled water) as cooling medium. To prevent the build-
up of algae, use common citric acid. This reliably prevents the spread of algae.
The cooler is fully SLI compatible. To set up a dual or triple SLI system, we offer special dual and triple links
which allow you to easily connect the coolers.
HEATKILLER® are products by
Please send your criticism, praise or suggestions to
the following address:
Watercool e.K
Zum Mevenbruch 6
D-17192 Waren - Warenshof
GERMANY
Tel: [phone]
Fax: [phone]
E-Mail: [email protected]
Web: www.watercool.de