WATERGUARD Solo User manual

Water Leak Detection Equipment
Waterguard Solo
Installation Guide V19
Waterguard Services Limited. Registered address: 22 Oakwell Business Centre, Oakwell View, Barnsley, South
Yorkshire, S71 1HX. Tel: [phone]. Email: [email protected].
IMPORTANT! INSTALLATION MUST BE CARRIED OUT ONLY BY THOSE COMPETENT IN
ELECTRICAL INSTALLATION. ANY DAMAGES INCURRED DUE TO IMPROPER
INSTALLATION ARE NOT COVERED UNDER WARRANTY.
Test….
To check the correct installation and operation of the Solo firstly change the maximum continuous flow
allowance to 10 minutes using the setup instructions. Run the water in the property and if the water supply
is cut off after 10 minutes the installation of the Solo is complete. Push the valve driver and after 10
seconds the controller will reopen the valve. Ensure to change the settings back to the preferred time once
testing is complete.
Setup….
All Waterguard Solo controls are pre-set to allow a maximum of 30 minutes continuous water flow, unless
an alternative time is requested at time of purchase. In order to change this default setting, follow the
instructions below:
Press and hold the valve driver button for 25 seconds, the valve driver is now in set up mode. Ensure you
do not release the button after the initially 25 seconds and the valve driver will flash as below in 5 second
intervals.
•1 flash = 10 minutes
•2 flashes = 20 minutes
•3 flashes = 30 minutes
•4 flashes = 40 minutes
Release the valve driver button once the LED indicator has shown the required number of flashes for the
time limited required. Set up complete.
© 2019 Waterguard Services Limited, All Rights Reserved
Technical Support….
Technical support and further product information is available during office hours. Please check all
electrical connections before contacting us.
Please call 01226 397987 to speak with one our technical experts, ensure to have your order details ready
so we can handle your query as efficiently as possible.
Success?
Power and unit operation are indicated by a solid red light on the controls. The LED will flash once per
second for approximately 2 minutes.

Wiring Diagram….
Step by Step Installation….
1. Fit valve assembly ensuring that the direction of flow arrows on both the valve and flow sensor are
correct for the direction of the flow of water supply. Do not over tighten or overuse PTFE tape.
Check for leaks after restoring the water supply.
2. Fix controls to chosen area.
3. Wire the solenoid valve to Solo Controls:
•Red to V
•Black to C
4. Wire the flow sensor to Solo Controls. One wire to C and one wire to F (colours connected not
relevant).
5. Connect power to the Solo controls using the 12V power pack or mains power supply.
6. Connect 3V lithium battery. DO NOT CONNECT THIS BEFORE POWER.
Ensure to see the reverse for set up and to check successful installation.
ATTENTION…..
It is important to strictly follow these instructions in full. The 3V lithium battery must not be used as a
temporary supply and must only be connected after mains power. Failure to do this will result in system
failure.
Waterguard Services Limited: 22 Oakwell Business Centre, Oakwell View, Barnsley, South Yorkshire, S71 1HX. Tel: [phone]. Email: [email protected]. ©2019 Waterguard Services Limited, All Rights Reserved
What You Will Have:
12V Complete Kit ❑
240V Complete Kit ❑
•Waterguard Solo control panel
•1 x 3V lithium battery
•Flow sensor
•Latching solenoid valve
•12V power pack
•1 x single pattress box
•2 x pairs push fit connectors
•Waterguard Solo control panel
•1 x 3V lithium battery
•Flow sensor
•Latching solenoid valve
•1 x single pattress box
•2 x pairs push fit connectors
12V Standard Kit ❑
240V Standard Kit ❑
•Waterguard Solo control panel
•1 x 3V lithium battery
•Flow sensor
•Latching solenoid valve
•12V power pack
•Waterguard Solo control panel
•1 x 3V lithium battery
•Flow sensor
•Latching solenoid valve
What You Will Need:
•Speaker cable, twin or three core flex (see step 3).
•3 core mains cable (where applicable, see step 6).
IMPORTANT: PLEASE READ THIS GUIDE IN FULL BEFORE INSTALLING.
MAINS SUPPLY
TO FUSED SPUR
12V POWER PACK
12V
SOLO
240V
SOLO
FLOW SENSOR
LATCHING SOLENOID VALVE
Step 5.
Step 6.
Step 6.
Step 4.
Step 3.