Waterstone 5500 Service manual

TRADITIONAL PLP PULLDOWN FAUCET
INSTALLATION INSTRUCTIONS
Model #s:
5500, 5600, 5610, 5200, 5210
5600
5500
5200
5610
5210

1 2 3 4
Turn o water supply. Observe all local
plumbing codes.
Inspect plumbing for signs of
damage. Replace as necessary.
DO NOT use petroleum based
products on this faucet.
REQUIRED TOOLS:
Phillips ScrewdriverAdjustable Wrench Channel Locks
BEFORE YOU BEGIN YOUR INSTALLATION:BEFORE YOU BEGIN YOUR INSTALLATION:
F
COUNTER
OR SINK
1. 2. 3. 4.
A
B
C
DE
A
C
B
PULLDOWN FAUCET INSTALLATIONPULLDOWN FAUCET INSTALLATION
Remove the clamp nut (A) and
washer (B) from the threaded
shroud (C).
Slide washer and thread the
clamp nut onto threaded shroud.
Tighten nut snug to underside of
sink or counter.
Turn faucet to the desired handle
position. Securely tighten clamp
screws (F).
Fit exible hoses (D) and spray
connection tube (E) through hole
on counter or sink. (No plumbers
putty is required. O-ring seals base).
Waterstone faucets are designed to be installed in 3 dierent faucet
positions. Choose to have the handle on left, front or right.Your faucet is
factory congured for the most common positions - a front and right side
installation.To reverse this and have the handle positioned on the left,
connect the hose for cold water to the hot supply and the hose for hot water
to the cold supply. This will maintain the relationship of pulling the handle
for hot water or pushing for cold water. HANDLE ON LEFT HANDLE IN FRONT HANDLE ON RIGHT
ORIGINAL FACTORY POSITION
MAY HIT BACKSPLASH
NEW ADJUSTED POSITION
CLEARS BACKSPLASH
H C
A
B
C D
A B E
E
G
C D F
F
HANDLE POSITIONHANDLE POSITION

AC
DE
F
B
CONNECT THE PULLDOWN SPRAY HOSECONNECT THE PULLDOWN SPRAY HOSE
Before connecting supply hoses,
ush supply stops to clear any
debris. Place a bucket underneath
stops and run water for 5 to 10
seconds.Turn water o. Carefully
position hot and cold supplies so
they will not interfere with other
hoses. Connect supply hoses (A)
to supply stops (B). DO NOT use
teon tape or plumbers putty.
Turn water back on and check for
leaks.
CONNECTING SUPPLY HOSESCONNECTING SUPPLY HOSES
A
B
HOW TO ADJUST HANDLE POSITION AND HANDLE TENSIONHOW TO ADJUST HANDLE POSITION AND HANDLE TENSION
On some kitchen countertops, the handle may hit the
backsplash when the faucet handle is positioned to the left
or right (Fig. 1). Waterstone gives you the option of adjusting
the handle 45 degrees to avoid hitting backsplash.
FIG.1
OPTIONAL DECORATIVE BUTTONSOPTIONAL DECORATIVE BUTTONS
Place a small standard screwdriver in slot at bottom of
metal ring that surrounds handle button (A). Gently
pry button from handle (B). Unscrew and remove
holding screw (C) and washer (D). Hold handle in a
vertical position. Wiggle and pull straight o faucet.
Rotate handle away from backsplash
45 degrees then slide handle back
onto valve stem (E). Insert holding
screw with washer and tighten. Snap
handle cap back into place. To adjust
handle tension, turn ring (F) clockwise
to increase or counterclockwise to
decrease handle tension.
HANDLE ON LEFT HANDLE IN FRONT HANDLE ON RIGHT
ORIGINAL FACTORY POSITION
MAY HIT BACKSPLASH
NEW ADJUSTED POSITION
CLEARS BACKSPLASH
H C
A
B
C D
A B E
E
G
C D F
F
A
C
B
Connect spray hose (A) to spray
connection hose tube (B).
NOTE – make sure spray hose
(A) and counter balance (C) are
free to slide up and down and
are not in conict with any
plumbing components or
items under sink.
ORIGINAL FACTORY POSITION
MAY HIT BACKSPLASH
NEW ADJUSTED POSITION
CLEARS BACKSPLASH
To change button, nd the slot (A) at bottom of retainer
ring (B). With a small standard screwdriver, g ently
pry retainer ring from faucet handle (C). Remove
button assembly (D). Insert new button by
lining up pin (E) on handle with hole (F)
on bottom of button assembly. With
slot facing down, press the button
retainer ring rmly back into
place.

CLEANING DEBRIS SCREENCLEANING DEBRIS SCREEN
B
C
A
1. Turn o water supplies
underneath sink and remove any
water pressure by opening the
faucet handle.
2. Unscrew sprayer (A) from spray
hose by holding knurled swivel (B).
3. Inspect, remove and clean debris
screen (C) in sprayer. Once cleaned,
replace debris screen and reattach
to swivel.
4. Close faucet handle and turn on
water supplies. Make sure sprayer
is secure and sealed by running
faucet.
B
C
D
A
1. 2. 3.
4.
1. Gently unscrew and remove spray face (A) by hand.
2. To remove O-ring (B), aerator (C) and spray face insert (D), push with nger from bottom.
3. Thoroughly rinse aerator with water until all debris is removed.
4. Place spray face insert back into spray face and spin until it clicks into place. Next, place
aerator and O-ring into spray face. Gently screw spray face, by hand, snuggly back onto
sprayer.
CLEANING AERATORCLEANING AERATOR

COUNTER
OR SINK
1-3/8”
HOLE
A
B
C
D
F
G
E
B
C
COUNTER
OR SINK
1-1/2”
HOLE
A
EXPOSE
THREADS D
1. 2. 3. 4.
1. 2. 3.
4. 5. 6.
INSTALL AIR SWITCH (OPTIONAL)INSTALL AIR SWITCH (OPTIONAL)
INSTALL SOAP/LOTION DISPENSER (OPTIONAL)INSTALL SOAP/LOTION DISPENSER (OPTIONAL)
Fill plastic bottle with soap or lotion.Thread
bottle (E) into bottom of dispenser shroud.
Pull and remove spout
(A) from dispenser
body (B). Remove
clamp nut (C) from
threaded shroud (D).
Slide red tubing (F)
into tube tting (G)
at bottom of spout.
Insert open end of
red tubing down
through dispenser
base and into
plastic bottle. Push down on spout
to secure over white
O-rings.
Pump spout a few
times to get soap or
lotion owing.
Fit dispenser body through 1-3/8”hole
on counter or sink. (No plumbers putty is
required. O-ring seals base). Screw clamp
nut onto shroud and tighten snug.
Slide washer up then screw the
clamp nut onto threaded shroud.
Hand tighten nut to underside of
sink or counter until snug.
Slide clear tubing
(B) into tube
tting (C) at
bottom of air
switch shroud.
Fit air switch and tubing through
1-1/2” hole on counter or sink.
(No plumbers putty is required.
O-ring seals base).
Before inserting air switch into
hole, loosen switch base (A)
until threads are exposed.

F
G
GARBAGE DISPOSAL
E
A
B
C
D
E
F
G
H
1-1/2”
HOLE
E
5. 6. 7. 8.
1. 2. 3.
4. 5. 6.
Unscrew and remove
top clamp nut (D)
from both threadings
on piping. Slide
gasket (E) o piping
and remove.
Twist and pull air gap
cover (A) o of upper
cap nut (B). Unscrew
and remove cap nut
from piping (C).
Slide gasket down and screw top clamp
nut back onto piping. Adjust the two
clamp nuts to t countertop thickness.
(No plumbers putty is required).
Screw cap nut back
onto top of piping
until snug. Slide air
gap over cap nut and
top clamp nut. Be
sure to have overow
holes (F) facing sink.
Slide small intake hose
(G) over small connector.
Slide larger drainage hose
(H) over large connector.
Tighten hose clamps.
Turn on water supply
and check for leaks.
From underneath
counter top, t air
gap piping upward
through 1-1/2”
hole.
INSTALL SINGLE PORT AIR GAP (OPTIONAL)INSTALL SINGLE PORT AIR GAP (OPTIONAL)
Tighten clamp screws (E)
securely with screwdriver.
Hand tighten switch base back
down to cover threads.
Slide other end of
tubing (F) into tube
tting at bottom of
control box (G).
Plug control box into undersink
electrical outlet. Plug garbage
disposal into either dual outlet.

VEN-038-TPLP Rev. D
41180 Raintree Court • Murrieta, CA 92562 • 1-888-304-0660 • 951-304-0520 • www.waterstoneco.com
G
H
L
M
K
J
A
D
E
C
B
F
1-1/2”
HOLE
1. 2. 3. 4.
5. 6.
Unscrew and remove top clamp
nut (D) from both threadings on
piping. Slide gasket (E) o piping
and remove.
Pull air gap (A) o of upper cap
nut (B). Unscrew and remove
cap nut from piping (C).
Slide gasket down and screw
top clamp nut back onto piping.
Adjust the two clamp nuts to
t countertop thickness. (No
plumbers putty is required).
Screw cap nut back onto
top of piping until snug.
Slide air gap over cap
nut and top clamp nut.
Be sure to have overow
holes (F) facing sink.
From underneath counter
top, t air gap piping upward
through 1-1/2”hole.
Slide small intake hose (G) over small connector.
Slide larger drainage hose (H) over large
connector. Tighten hose clamps.
Third intake hole (J)
has 3 options. Use
hose connector (K) for
additional dishwasher,
use ltration hose
connector (L) for reverse
osmosis unit, or use
solid cap (M) to plug
third hole.
INSTALL DUAL PORT AIR GAP (OPTIONAL)INSTALL DUAL PORT AIR GAP (OPTIONAL)