Waterstone 3600-12 User manual

41180 Raintree Court • Murrieta, CA 92562 • 1-888-304-0660 • 951-304-0520 • www.waterstoneco.com
3800 3825
3600-12
4300
4200
4100-12
3600-18
4100-18
3900
4700 4900
3500 3925
4800
KITCHEN AND PREP
FAUCET INSTALLATION
INSTRUCTIONS
Kitchen Model #s:
3600-12
3600-18
3800
3825
4100-12
4100-18
4200
4300
Prep Model #s:
3500
3900
3925
4700
4800
4900

A
B
D
F
E
C
COUNTER
OR SINK
1. 2. 3. 4.
Slide washer and thread the
clamp nut onto threaded shroud.
Tighten nut snug to underside of
sink or counter.
Turn faucet to the desired handle
position. Securely tighten clamp
screws (F).
FAUCET INSTALLATION
Remove clamp nut (A) and
washer (B) from threaded
shroud (C).
Fit exible hoses (D) and rigid
sidespray tube (E) through hole on
counter or sink. (No plumbers putty
is required. O-ring seals base).
1 2 3 4
Turn o water supply. Observe all local
plumbing codes.
Inspect waste and water
supplies for signs of damage.
Replace as necessary.
DO NOT use petroleum
based products on this
faucet.
REQUIRED TOOLS: PARTS INCLUDED:
2. Phillips Screwdriver1. Adjustable Wrench
BEFORE YOU BEGIN YOUR INSTALLATION:
INSTALLATION GUIDE
HK-THC-XX*
HANDLE BUTTON KIT (TRADITIONAL ONLY)
HK-USM1250
UNDER SINK MOUNTING HARDWARE KIT (1-1/4”)
*XX represents nish

RED FOR HOT
BLUE FOR COLD
H C HC
COMPASS H/C COMPASS C/H FINISH MATCH
COUNTER
OR SINK
E
F
G
A
C
B
D
1. 2. 3. 4.
4. Connect and tighten end of
sidespray hose to sidespray hose
tube.
3. Remove hose cap (E) from end
of sidespray hose tube (F) on
faucet (G).
CONNECTING OPTIONAL SIDE SPRAY
Waterstone faucets are designed for 3 dierent faucet positions. Handle on left,
front and right. Your faucet is congured for the most common installation (see
below). To reverse this and have the handle positioned on the left, connect the
hose for cold water to the hot supply and the hose for hot water to the cold
supply.This will maintain the relationship of pulling the handle for hot water or
pushing for cold water.
HANDLE ON LEFT HANDLE IN FRONT HANDLE ON RIGHT
ORIGINAL FACTORY POSITION
MAY HIT BACKSPLASH
NEW ADJUSTED POSITION
CLEARS BACKSPLASH
H C
AB
C D
A B E
E
G
C D F
F
1. Before connecting supply hoses,
ush supply stops to clear any debris.
Place a bucket underneath stops and
run water for 5 to 10 seconds. Turn
water o.
2. Carefully position hot and cold
supplies so they will not interfere with
other hoses.
3. Connect supply hoses (A) to supply
stops (B). DO NOT use teon tape or
plumbers putty. Turn water back on
and check for leaks.
CONNECTING SUPPLY HOSES HANDLE POSITION
OPTIONAL DECORATIVE BUTTONS
(TRADITIONAL ONLY - 3 INCLUDED)
OPTIONAL HOT COLD INDICATOR RING
(CONTEMPORARY ONLY)
1. To remove, place a small standard screwdriver in the
slot at bottom of metal ring that surrounds the handle
buttons. Gently pry the button from faucet handle.
2. To replace, position button and snap in with thumb.
1. To reverse, or remove Hot and Cold Indicator Ring,
unscrew the metal cap, remove ring and ip.
2. Slide ring back onto handle and screw metal cap
back on.
A
B
1. Insert side spray base (A) into
side spray hole on your sink or
counter. No plumbers putty is
required. O-ring seals base. Slide
washer (B), thread attaching nut
(C) and securely tighten.
2. Slide sidespray hose (D)
through side spray base.

HANDLE ON LEFT HANDLE IN FRONT HANDLE ON RIGHT
ORIGINAL FACTORY POSITION
MAY HIT BACKSPLASH
NEW ADJUSTED POSITION
CLEARS BACKSPLASH
H C
AB
C D
A B E
E
G
C D F
F
HANDLE ON LEFT HANDLE IN FRONT HANDLE ON RIGHT
ORIGINAL FACTORY POSITION
MAY HIT BACKSPLASH
NEW ADJUSTED POSITION
CLEARS BACKSPLASH
H C
AB
C D
A B E
E
G
C D F
F
1. Unscrew and remove the metal cap (A). Remove Hot and Cold Indicator Ring (B).
2. Unscrew and remove holding screw (C) and washer (D).
3. Hold handle (E) in a vertical position. Pull straight o faucet. Rotate handle
away from backsplash then slide handle back onto valve stem (F).
4. Insert holding screw with washer and tighten. Slide Hot and Cold Indicator
Ring onto handle and thread metal cap back into place.
5. To adjust handle tension, turn ring (G) clockwise to increase or
counterclockwise to decrease handle tension.
1. Place a small standard screwdriver in the slot at the bottom of metal ring that surrounds the
handle caps (A). Gently pry the button from faucet handle (B).
2. Unscrew and remove holding screw (C) and washer (D).
3. Hold the handle (B) in a vertical position. Pull straight o faucet. Rotate handle away from
backsplash then slide handle back onto valve stem (E).
4. Insert holding screw with washer and tighten. Snap handle cap back into place.
5. To adjust handle tension, turn ring (F) clockwise to increase or counterclockwise to decrease
handle tension.
HOW TO ADJUST HANDLE POSITION AND HANDLE TENSION
CONTEMPORARY
TRADITIONAL
1. Gently unscrew and remove spout tip (A) by hand.
2. Remove O-ring (B).To remove aerator (C), push with nger from bottom.
3. Thoroughly rinse aerator with water until all debris is removed.
4. Place aerator, then O-ring back into spout tip.
5. Gently screw spout tip, by hand, snuggly back onto spout.
Depending on quality of your household water, the aerator and
debris screen may become clogged.We recommend cleaning
one week after installation, then a minimum of once of year
thereafter. To remove the debris, follow the steps below.
CLEANING AERATOR AND DEBRIS SCREEN
B
C
A
1. 2. 3. 4. 5.
On some kitchen countertops, the handle may
hit the backsplash when the faucet handle is
positioned to the left or right (Fig. 1).Waterstone
gives you the option of adjusting the handle 45
degrees to avoid hitting backsplash.
FIG.1
VEN-038-KITP Rev. C