Waterstone 6100-12 User manual

6100-12 6100-18 6200 6300
6250 63506150-18
6150-12
7600-12
7600-18
7800
7825
BRIDGE FAUCET INSTALLATION
INSTRUCTIONS
Model #s:
6100-12
6100-18
6150-12
6150-18
6200
6250
6300
6350
7600-12
7600-18
7800
7825

4”
RECOMMENDED HOLE SIZE 1-3/8”
SINK OR MOUNTING SURFACE
4”
8”
1.
FAUCET HOLE PLACEMENT
NOT TO SCALE
Recommended deck hole 1-3/8”. Drill holes for bridge faucet in mounting surface 8”on center.
OPTIONAL SIDE SPRAY: We recommend installing the side spray hole a minimum of 4-3/4”away
from nearest mounting hole of faucet.
1 2 3 4
Turn o water supply. Observe all local
plumbing codes.
Inspect waste and water
supplies for signs of damage.
Replace as necessary.
DO NOT use petroleum
based products on this
faucet.
REQUIRED TOOLS: PARTS INCLUDED:
2. Phillips Screwdriver1. Adjustable Wrench
BEFORE YOU BEGIN YOUR INSTALLATION:
INSTALLATION GUIDE
HK-USM1250
UNDERSINK MOUNTING HARDWARE (1-1/4”)

A
B
C C
A
B
COUNTER
OR SINK
ED
D
F F
1. 2.
3. 4.
1. Before connecting supply hoses, ush supply stops to clear any debris. Place a bucket underneath stops
and run water for 5 to 10 seconds.Turn water o.
2. Carefully position hot and cold supplies so they will not interfere with other hoses.
3. Connect supply hoses (A) to supply stops (B). DO NOT use teon tape or plumbers putty. Turn water
back on and check for leaks.
Slide washer and thread the clamp nut onto threaded shroud.
Tighten nut snug to underside of sink or counter. Securely tighten clamp screws (F).
FAUCET INSTALLATION
Remove clamp nut (A) and washer (B) from threaded shroud (C).
Fit exible hoses (D) and rigid sidespray tube (E) through holes on
counter or sink. (No plumbers putty is required. O-rings seals base).
CONNECTING SUPPLY HOSES A
B

VEN-038-BRDG Rev. D
41180 Raintree Court • Murrieta, CA 92562
1-888-304-0660 • 951-304-0520 • www.waterstoneco.com
COUNTER
OR SINK
E
F
G
A
C
B
D
1. 2. 3. 4.
Connect and tighten end of
sidespray hose to sidespray
hose tube. Check for leaks.
Remove hose cap (E) from end
of sidespray hose tube (F) on
faucet (G).
CONNECTING OPTIONAL SIDE SPRAY
Insert side spray base (A) into side
spray hole on your sink or counter.
No plumbers putty is required.
O-ring seals base. Slide washer
(B), thread attaching nut (C) and
securely tighten.
Slide sidespray hose (D)
through side spray base.
1. Gently unscrew and remove spout tip (A) by hand.
2. Remove O-ring (B).To remove aerator (C), push with nger from bottom.
3. Thoroughly rinse aerator with water until all debris is removed.
4. Place aerator, then O-ring back into spout tip.
5. Gently screw spout tip, by hand, snuggly back onto spout.
Depending on quality of your household water, the aerator
and debris screen may become clogged. We recommend
cleaning one week after installation, then a minimum of
once of year thereafter. To remove the debris, follow the
steps below.
CLEANING AERATOR AND DEBRIS SCREEN
A
B
C
2. 3. 4. 5.1.