Galvin Engineering Capstan 175.91.00.03 User manual

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 7 July 2023, Page 1of 5
Capstan CP Lead Safe½ Turn Wall Top Ass Child
Safety Tap
PRODUCT CODE:
- 175.91.00.03
SPECIFICATIONS
−The Galvin Engineering Safety Tap has been devised to add another precautionary aid against children
tampering with hot water. Once the flow is set, young children are unable to tamper with the flow until
reset by an adult.
−The main body is made of solid dezincification resistant (DR) brass rod.
−SBA’s includes brass ceramic disc component, with red and blue indicator.
−Lead Safe™brass construction*
IMPORTANT: All taps are tested in accordance with AS/NZS 3718 and leave our premises in good working
order.
*As ‘lead free’ is not currently defined by law in Australia and New Zealand, we have based our definition of Lead Safe™on the requirements of Sec. 1417 of the USA’s Safe Drinking Water Act
(SDWA) and the relevant US standards NSF61 / NSF372. The SDWA defines ‘lead free’ as “not more than a weighted average of 0.25% lead when used with respect to the wetted surface of
pipes, pipe fittings, plumbing fittings and fixtures”.
WARNINGS: Special attention to be paid on notes, photos, image, or drawings of assembly
steps marked with the warning symbol.
TECHNICAL DATA
Inlet
G 5/8” BSP - Male
Outlet
N/A
Headwork
Ceramic Disc
Working Pressure Range (kPa)
Min
50
Max
500
Working Temperature Range (°C)
Min
5
Max
65
Nominal Flow Rate (LPM)
N/A
Finish
Chrome
NOTE: Galvin Engineering continually strive to improve their products. Specifications may change without
notice.
TOOLS REQUIRED

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 7 July 2023, Page 2of 5
−Power drill
−Spanner and hex key
−Thread tape
PRE-INSTALLATION - MOUNTING DETAILS
Note: Before installation, all lines must be flushed. Galvin Engineering recommends the installation of
strainers and pressure reducing valves to ensure clean consistent supply. Debris or poor water quality could
cause the push button to seize or fail to seal.
Wall body
−Check that the existing valve body complies to AS/NZS 3718. Inwall body must be G5/8” FI and
body should be between 0 and 15mm behind the finished wall surface.

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 7 July 2023, Page 3of 5
INSTALLATION
INSTALLATION COMPLIANCE: Galvin Engineering products must be installed in accordance with these
installation instructions and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements.
Water and/or electrical supply conditions must also comply to the applicable national and/or state standards.
Failing to comply with these provisions shall void the product warranty and may affect the performance of the
product.
1. Dissassembly
−Remove the protective cap, handle, dress
flange and the retaining spring from the
assembly. Unscrew the 1/2 turn ceramic
headpart from the threaded sleeve
assembly.
2. Fit wall flange
−Screw ceramic headpart into the valve body
by hand, tighten using a 17mm spanner.
−Refit threaded sleeve and spindle.
−The 1/2 turn ceramic headpart MUST be
fitted into the wall body prior to refitting
the threaded sleeve and spindle. DO NOT
tighten headpart by using the spindle or
the threaded sleeve.
3. Fit wall flange and handle
−Re-fit the safety tap sleeve assembly, then
fit the dress flange. Insert the spring into the
dress flange and fit the handle and button
over the top.
3. Fit wall flange and handle
−Ensure the spindle is in the closed position and
firmly press the handle onto the spindle in the
desired orientation.
−Check operation of handle. They should turn
freely for a full ½ turn.
−Once handle is secure; fit the appropriate
water temperature indicator.
−Secure the handle in position using the
supplied washer and stainless steel cap screw.
Valve Body
Protective cap
Handle
Retaining Spring
Ceramic
Headpart
Spindle
Ceramic
Headpart
Spindle
Spindle
Flange
Retaining Spring
Handle
Flange

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 7 July 2023, Page 4of 5
4. Fit water temperature indicator
−Once handle is secure; fit the appropriate
water temperature indicator.
5.Testing
Check the operation of the unit and inspect for any leaks.
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Taps are dripping water
Ceramic discs are worn or damaged
Remove and inspect SBA.
Remove debris and/or
replace SBA if damaged.
Tap seat is damaged
Refurbish tap seat using a
reseating tool.
Water is not flowing from tap
Water is turned off
Turn water on
Aerator or flow regulator is blocked by
debris
Remove aerator and/or flow
regulator from tap and remove
debris. Install an inline strainer.
Obstruction on spout
Check if there are obstructions
hindering the water flow in the
spout and take it out.
Handle is loose
Screw has come loose
Tighten handle screw
Temp. indicator

Version 2, 11 July 2023, Page 5of 5
Product Installation Guidelines
Version 1, 7 July 2023, Page 5of 5
SERVICE AND MAINTENANCE
1. Turn off the water supply and turn on the tap handle to drain water from the bodies.
2. Remove the temperature indicator from the handle.
3. Remove the handle from the tap.
4. Unscrew the ceramic headpart from the body.
5. Check the o-ring on the ceramic headpart for wear and damage. Replace if required.
6. Clean the headpart and the body of any debris.
7. Replace the cartridge and hand-tighten back into the body.
8. Follow the product installation guidelines for the relevant product re-assembly method.
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering
Pty Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or
implied. Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied,
including but not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule
in the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
Manufacturer’s warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy
for breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special
or consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance
or alteration of the product.