wattstopper WN-100 User manual

WN-100
Motion Sensor
Nightlight Switch
SPECIFICATIONS
WN-100-120
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120VAC, 60Hz
Power Consumption . . . . . . . . . . . . . . . . . . . .0.92W maximum
Load Requirements . . . . .0-500W Incandescent, Fluorescent
. . . . . . . . . . . . . . . . . . . . . .and Compact Fluorescent
Horsepower Rating . . . . . . . . . . . . . . . . . . . . . . . . . . .1/6 HP
WN-100-277
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .277VAC, 60Hz
Power Consumption . . . . . . . . . . . . . . . . . . . . .0.92W maximum
Load Requirements . . . . . . . . . . . . . . . . . . . .800W Fluorescent
General
Time Delay Adjustment . . . . . . . .Fixed 15 minute, 30 minute,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 hour, 2 hour
Operating Temperature Range . . . . . . . . . .32-131°F (0-55°C)
Operating Humidity Range . . . . . . .95% RH, non-condensing
Installation Instructions
US Patent Number:
4,787,722

UNIT DESCRIPTION
The Watt Stopper WN-100 is a motion sensing wall switch and nightlight that
controls lighting based on occupancy. The sensor uses passive infrared (PIR)
technology to sense human motion in a controlled space. It must have a clear
view of occupants in the space in order to detect occupancy. Obstructions such
as furniture blocking the sensor’s lens may prevent occupancy detection.
Note:Windows, glass shower doors, etc. will obstruct the WN-100’s view and
may prevent detection.
Through the WN-100’s mode selection, the user can specify ON functions and
time delay (see Sensor Adjustment & Programming section).
OPERATION
ON-Mode Functions (Manual-ON & Automatic-ON):
Manual-ON:
When the WN-100 is set to Manual-ON, users must turn lights on by pushing
the ON/OFF button. Lights will not turn on automatically with occupancy in
the Manual-ON mode. However, for a grace period of 30 seconds after
shut-off, the WN-100 will turn the load back on automatically when motion is
detected.
Automatic-ON:
In Automatic-ON mode, the WN-100 automatically turns lights on when a
designated space becomes occupied.
Note:In both Manual-ON and Automatic-ON, the ON/OFF button turns lights
off. The ON/OFF button must be pressed again to turn lights back on.
Time Delay:
The WN-100 automatically turns lights off after a space becomes vacant and
a preset time interval, or time delay, elapses. If lights are left on and no
motion is detected for the time delay selected (factory default = one hour), the
WN-100 automatically turns lights off.
Nightlight:
In the factory default mode, the nightlight remains on whenever the load is
off, regardless of occupancy.
The nightlight can be disabled from constant illumination (see “End User
Options” in the Sensor Adjustment & Programming section). However, when
motion is detected by the WN-100 while in Manual-ON mode, the nightlight
will automatically turn on and remain on until 90 seconds after the room
becomes vacant again. In this situation, nightlighting is provided only when
the room is in use.
If the nightlight remains disabled for 48 hours, it will automatically switch to
the default (enabled) mode.

COVERAGE PATTERNS
The WN-100 has a coverage range of 180 degrees and a maximum coverage
area of 300 sq. ft. To maintain its coverage capacity and optimally detect
motion, the WN-100 must have a clear and unobstructed view.
4.0'
(1.2m)
25'
(7.6m)
floor
Hot
Black
Neutral
White
Load
Load
Red
Neutral
White
TOP
INDOOR USE ONLY
ON
1
Ground
Green
Single-sensor wiring
25'
(7.6m)
10'
(3.1m)
WIRING
Visit our website for FAQs: www.wattstopper.com

INSTALLATION
Caution: A neutral connection is required for sensor operation.
A qualified electrician should be consulted regarding the availability of a
neutral in your particular installation.
1. Make sure that power has been
turned off at the circuit breaker.
2. Connect the existing wires to the
sensor terminals.
• Hot or Black to Line;
Load or Red to Load;
Ground or Green to Ground;
Neutral or White to Neutral.
•Do not allow any bare wire to
show above the connector.
3. Attach the sensor to the wall box
by inserting screws into the two
wide holes on the top and bottom
of the attached metal bracket. Line them up with the holes in the wall box
and tighten.
4. Turn on the circuit breaker. Push the ON/OFF button and the lights will
turn on.
TOP
INDOOR USE ONLY
TOP
INDOOR USE ONLY
Insert or wrap wire as shown. Tighten screw in the
clockwise direction.
CAUTION: TURN THE POWER OFF
AT THE CIRCUIT BREAKER BEFORE WIRING.
Call 800.879.8585 or 972.578.1699 for Technical Support
Wire insert
Optional
wire wrap
Strip Gauge
#12 – #14 AWG
Cu Wire Only

SENSOR ADJUSTMENT & PROGRAMMING
The WN-100 is designed for installation in hotel rooms and other semi-public
spaces. Custom setup features are intended for facility or installing personnel
only. Therefore, the Program Mode switch is located behind the cover plate. To
enable the Programming mode, the single DIP switch must be in the ON
(Program) position.
Programming the WN-100:
1. Slide the Program Mode switch (normally
covered by the light switch cover plate) to
the ON (Program) position. The nightlight
will flash, counting out the selected
operating mode (one flash then a pause =
mode 1, two flashes then a pause = mode
2, and so on)
2. Press the ON/OFF button to advance
through the modes. When you reach the
desired mode, slide the Program Mode
switch to the DOWN (End User) position.
3. When the Program Mode switch is returned
to the DOWN (End User) position, the
WN-100 will operate in Test Mode for five
(5) minutes. During this period, the time
delay will be 15 seconds and the WN-100
will operate as “Automatic-ON”. After five
(5) minutes, the WN-100 will use the
parameters of the selected mode.
Note: Do not leave the Program Mode Switch in the UP (Program) position. The
WN-100 will only operate properly in the DOWN (End User) position.
Mode Selections:
Flashes Time Delay Mode
R1 hour * Manual-On * Factory default
RR 2 hours Manual-On
RRR 30 minutes Manual-On
RRRR 15 minutes Manual-On
RRRRR 15 minutes Automatic-On
End User Options:
To disable the nightlight, press and hold the ON/OFF button. After one-half
second, the nightlight will display the Enabled/Disabled status (lit = nightlight
enabled, unlit = nightlight disabled). To change the status, continue to press and
hold the ON/OFF button. After five (5) seconds, the WN-100 changes state (for
more details, see “Nightlight” in the Operation section).
TOP
ON
1
INDOOR USE ONLY
TOP
ON
1
INDOOR USE ONLY
WN-100
Program
Mode
Switch
Nightlight
glows
behind lens
ON/OFF
Button

TROUBLESHOOTING
To test the WN-100:
Initiate the WN-100 Test Mode by sliding the Program Mode Switch up to the
ON (Program) position then back to the DOWN (End User) position.
When the switch is returned to the DOWN (End User) position, there will be a
five-minute test period. During this period, the time delay will be 15 seconds,
and the WN-100 will operate as “Automatic-ON”.
Move within the coverage zone of the WN-100 to trigger detection, then move
out of the coverage zone (see Coverage Patterns section). The load should
turn off within 15 seconds and the nightlight should subsequently turn on.
Repeat as necessary to ensure that the desired coverage areas are within
detection range.
Lights will not turn on (nightlight is illuminated):
1. Press ON/OFF button, lights should turn on. If not, check sensor wire
connections to the load.
2. Check the lamp.
Lights will not turn on (nightlight is NOT illuminated):
1. Check the sensor wire connections.
2. Make certain that the circuit breaker is on and functioning.
3. Call 800.879.8585 for technical support.
Lights turn OFF but nightlight does not turn ON:
1. Make sure the nightlight is not in Disable mode.
Call 800.879.8585 or 972.578.1699 for Technical Support

When ordering, add -W for white, -I for ivory for -A for light almond to the catalog number.
* One ASP-211 is included with each sensor.
WN-100-120 Motion Sensor Nightlight Switch
120VAC, 60Hz
WN-100-277 Motion Sensor Nightlight Switch
277VAC, 60Hz
ASP-211* Cover plate for single-gang box
ASP-422 Blank cover plate for double-gang box
ASP-432 Cover plate for double-gang box with switch option
ORDERING INFORMATION
WARRANTY INFORMATION
Watt Stopper/Legrand warranties its products to be free of defects in
materials and workmanship for a period of five (5) years. There are no
obligations or liabilities on the part of Watt Stopper/Legrand for
consequential damages arising out of, or in connection with, the use or
performance of this product or other indirect damages with respect to loss of
property, revenue or profit, or cost of removal, installation or reinstallation.
2800 De La Cruz Boulevard, Santa Clara, CA 95050
Technical Support: 800.879.8585 • 972.578.1699
www.wattstopper.com
02374r5 05/2005