WE-EF FLC121 User manual

WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Projector
FLC121 #2 LED
FLC131 #2 LED
FLC141 #3 LED
Surge Protection
This product features built-in surge protection circuitry in compliance with
applicable standards.
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and secondary
(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained in this
document for details.

1
IP67, Class I, ta= 40°C
Projector
60
300
ø 105
FLC121 #2
FLC131 #2
FLC141 #3 80
ø 180
430
Weight kg
for FLC121 #2 1.7
for FLC131 #2 2.5
for FLC141 #3 4.4
ø 6.5-10.5 mm

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
E\DVXLWDEO\TXDOLƂHGDQGWUDLQHGSURIHVVLRQDO
Warning: Do not open luminaire while mains supply is switched on.

3
Installation Procedure
1) Switch off mains electrical supply.
 5HPRYHPRXQWLQJƃDQJHAby loosening screw B.
Detach terminal connector C.
3) Check that rating shown on luminaire label
conforms with mains electrical supply.
 'HWHUPLQHSRVLWLRQVIRUƂ[LQJVFUHZVD.
Drill relevant holes Eand insert wall plugs F.
Warning: Ensure not to damage any electric cable,
water pipe or other devices while drilling holes.
5) Feed mains supply cable Gthrough the pressure
screw IZKLOHVHWWLQJPRXQWLQJƃDQJHAin posi-
WLRQ7RƂ[PRXQWLQJƃDQJHA, insert and tighten
screws D. The pre-installed packing ring His
suitable for cable diameters 7 to 9.5 mm. For larger
cable diameters (9 to 12 mm) use the auxiliary
packing ring supplied. Then tighten the pressure
screw I(Fig. I).
6) Connect mains supply cable Gleads to respective
terminals in terminal connector C(L = Phase,
N = Neutral, = Earthing).
7) Ensure that all surfaces are clean and dry. Position
OXPLQDLUHRYHUPRXQWLQJƃDQJHAand attach termi-
nal connector C. Turn luminaire towards object to
be illuminated. Tighten screw B.
8) Loosen screw Mslightly. Aim luminaire in desired
direction, retighten screw M.
Installation
The product must be installed and maintained by a
VXLWDEO\TXDOLƂHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW
building/construction and/or electrical regulations and
relevant legislation.
Warning: Switch off mains electrical supply prior to
installing and connecting the luminaire.
Notice:,IWKHOXPLQDLUHLVPRGLƂHGE\DQ\ERG\RWKHU
than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-
sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation
and/or application, and the consequences thereof, are
excluded.

4
I

5
Fig. I

TO9206W0617 © WE-EF 2017
7HFKQLFDOVSHFLƂFDWLRQVDUH
subject to change.
www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United Kingdom
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
LQIRDVLDSDFLƂF#ZHHIFRP
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]