WE-EF FLC121 User manual

WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Projector
FLC121 #1 LED
FLC131 #1 LED
Surge Protection
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and
secondary (Type 2) surge arrestors in compliance with EN61643-11/
IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and
activated prior to luminaire installation. Also, disconnect luminaires before
operating high-power devices such as, for example, electrical arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained in this
document for details.
FLC141 #1 LED
ESD Sensitive Product
This product is Electrostatic Discharge
sensitive. The cable provided is
connected directly to the LED PCB.
Ensure appropriate grounding measures
are taken when installing this product.
INSTALLER
HOTLINE
[phone]
7am – 7pm AEST

1
Projector
Mounting Accessories
FLC121 #1 FLC131 #1
IP66, Class I, ta = 40°C
CF-FLD1
SF-FLD1
)ODWVXUIDFHƂWWHU
SF-FLD1 for FLD/FLC100 #1 145-9535
&ROXPQƂWWHU
CF-FLD1 for FLD/FLC100 #1 145-9536
FLC141 #1

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
E\DVXLWDEO\TXDOLƂHGDQGWUDLQHGSURIHVVLRQDO
Warning: Do not open luminaire while mains supply is switched on.
Installation
The product must be installed and maintained by a VXLWDEO\TXDOLƂHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW
building/construction and/or electrical regulations and relevant legislation.
Warning: Switch off and isolate the mains electrical supply prior to installing and connecting the luminaire.
Notice:,IWKHOXPLQDLUHLVPRGLƂHGE\DQ\ERG\RWKHU than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation and/or application, and the consequences thereof, are
excluded

3
Installation Procedure
Installation –)ODWVXUIDFHƂWWHU
1) Switch off and isolate the mains electrical supply.
2) Detach strain relief clip KIURPƃDWVXUIDFHƂWWHUB.
Attention: Keep strain relief clip Kfor locking cable
later. (step 6 in this installation instruction)
3) Feed cable Cfrom luminaire Athrough pivot I and
hole LRIƃDWVXUIDFHƂWWHUT.
 'HWHUPLQHSRVLWLRQVIRUƂ[LQJVFUHZV D. Drill rel-
evant holes Qand insert nylon plugs R. Insert and
tighten screws D.
Warning: Ensure not to damage any electrical
cable, water pipe or other items drilling holes.
5) Loosen screw MRQVOLSƂWWHUH(do not turn it out)
XQWLOWKHVSOLSƂWWHUFDQEHRSHQHG&RQQHFWOXPL-
naire AZLWKƃDWVXUIDFHƂWWHUTE\VOLGLQJVOLSƂWWHU
Hover pivot I, while pulling cable Cthrough hole L
and turning luminaire Atowards object to be
LOOXPLQDWHG(QVXUHVOLSƂWWHUHis properly seated
on pivot I, then tighten screw M.
6) Clamp strain relief clip Kon the cable C and press
into the hole LRIƃDWVXUIDFHƂWWHUB. Ensure the
strain relief clip Kis properly placed in position to
lock the cable (Fig.I).
7) Connect the cable C to the matching Control Gear
Box (CGB) as per the supplied instructions.
8) Loosen screws N and O slightly. Then aim
luminaire in desired direction and tighten screws N
and O.
Installation –&ROXPQƂWWHU
6XLWDEOHIRUFROXPQGLDPHWHUŰPP
1) Switch off and isolate the mains electrical supply.
 'HWHUPLQHSRVLWLRQIRUƂ[LQJVFUHZVDand cable
entry hole F. Drill relevant holes Eand F on column
X. Ensure cable entry hole FKDVVXIƂFLHQWGLDPHWHU
to feed cable Cfrom luminaire A.
 6HWDQGƂ[FROXPQƂWWHUBin position. Insert and
tighten screws D.
4) Feed cable Cfrom luminaire Athrough pivot I and
cable entry hole Fon column X, while connecting
luminaire AZLWKFROXPQƂWWHUBE\VOLGLQJVOLSƂWWHU
Hover pivot I. Turn luminaire Atowards object to
EHLOOXPLQDWHG(QVXUHWKHVOLSƂWWHUHis properly
seated on pivot I, then tighten screw M.
5) Check that rating shown on luminaire label con-
forms with mains electrical supply.
6) Connect the cable C to the matching Control Gear
Box (CGB) as per the supplied instructions.
7) Loosen screws N and O slightly. Then aim luminaire
in desired direction and tighten screws N and O.

4
Fig. I Strain relief clip locking
)ODWVXUIDFHƂWWHU

5
&ROXPQƂWWHU

6

www.we-ef.com
TO9210W0817 © WE-EF 2018
7HFKQLFDOVSHFLƂFDWLRQVDUH
subject to change.
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United Kingdom
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
LQIRDVLDSDFLƂF#ZHHIFRP
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]
INSTALLER
HOTLINE
[phone]
7am – 7pm AEST