WE-EF FLC301 User manual

Surge Protection
This product features built-in surge protection circuitry in compliance
with applicable standards.
For comprehensive protection of a luminaire installation against lightning
and electrical surges,it is essential to cover mains supply and data input
lines at the distribution board level,by using respective primary (Type 1)
and secondary (Type 2) surge arrestors in compliance with EN61643-11/
IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and
activated prior to luminaire installation.Also,disconnect luminaires
before operatinghigh-power devices such as, for example,electrical
arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained
in this document for details.
Installation tools
Mounting hardware used on this product
includes fasteners with hexalobular
socket heads (ISO 10664).Installation
requires the use of matching tools.
WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Projector
Spigot mounted
FLC301
FLC311
FLC321

1
Projector
Spigot mounted
FLC301
FLC311
FLC321
IP66, IK08. Class I. Ta= 40°C
Weight kg
for FLC301 Spigot mounted 0.7
for FLC311 Spigot mounted 1.6
for FLC321 Spigot mounted 2.6

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces,no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried
RXWE\DVXLWDEO\TXDOLĥHGDQGWUDLQHGSURIHVVLRQDO
Warning: Do not open luminaire while mains supply is switched on.
Mounting Accessories
)ODWVXUIDFHĥWWHU
SF-FLC1 for FLC301 Spigot mounted 145-9535
&ROXPQĥWWHU
CF-FLC1 for FLC301 Spigot mounted 145-9536
Ground spike
EF1 for FLC301 Spigot mounted 310-9102
Junction box
JB1 with side entry 310-9002
JB1 with wall entry 310-9025

3
Installation
The product must be installed and maintained by a VXLWDEO\TXDOLĥHGSURIHVVLRQDOLQFRPSOLDQFH
with latest building/construction and/or electrical regulations and relevant legislation.
Warning: 6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\SULRUWRLQVWDOOLQJDQGFRQQHFWLQJWKHOXPLQDLUH
Notice:,IWKHOXPLQDLUHLVPRGLĥHGE\DQ\ERG\RWKHUWKDQWKHRULJLQDOPDQXIDFWXUHUWKHQWKHZDUUDQW\
will no longer be valid and shall become the full responsibility of the modifying person/organisation.
Claims based on defects attributable to improper installation and/or application, and the consequences
thereof, are excluded.
The installation on site must comply with local and/or national health and safety regulations.

4
1) 6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\
Installation Procedure
2) Check that rating shown on luminaire label
conforms with mains electrical supply.
(example)
3) Loosen screw A. 4) Place luminaire on one of the following
mounting accessories.
Mounting accessory installation instruction
is available in additional document,
TO9253W.
FLC301-LED 220-240V50-60Hz
145-XXXX SOE XXXXXXX
LED 3000K 4W item no.XXX
10/20 IP66

5
&ROXPQĥWWHU
3ULRUWRLQVWDOODWLRQRIFROXPQĥWWHU
feed cable Bfrom luminaire Cthrough pivot,
cable entry Gand cable gland Dof column
ĥWWHUH.6OLGHVOLSĥWWHUFover pivot.
)ODWVXUIDFHĥWWHU
3ULRUWRLQVWDOODWLRQRIVXUIDFHĥWWHU
feed cable Bfrom luminaire Cthrough pivot G
and cable gland DRIVXUIDFHĥWWHUE. Slide
VOLSĥWWHUFover pivot.
Ground spike
4.3) Feed cable Bfrom luminaire Cthrough
pivot Iand cable gland Dof ground spike K.
6OLGHVOLSĥWWHUFover pivot.
Junction box
4.4) Feed cable Bfrom luminaire Cthrough
pivot and cable entry Lof junction box M.
6OLGHVOLSĥWWHUFover pivot.

6
5) Turn luminaire towards object to be
LOOXPLQDWHG(QVXUHVOLSĥWWHULVSURSHUO\
seated on pivot,then tighten screw A.
6) Loosen screw N. Aim luminaire in desired
direction and tighten screw N.
)RUĦDWVXUIDFHĥWWHUFROXPQĥWWHUDQG
ground spike: Tighten cable gland D.
8) For accessory Linear Spread Lens IO-180:
Turn frame Oto set desired orientation of light.
7) Connect mains supply cable Gleads to
respective terminals in terminal connector C:
For FLC301
a) ON-OFF (L = Phase, N = Neutral,
= Earthing)
b) ON/OFF 24VDC (+ = positive pole,
ŝ= negative pole)
c) DALI 24VDC (+ = positive pole, ŝ= negative
pole, DA/DA= DALI control line,
= Earthing)
For FLC311/321
a) ON-OFF (L = Phase,N = Neutral,
= Earthing)
b) 0-10V 24VDC (+ = positive pole,
ŝ= negative pole,Dŝ/D+ = 0-10V
control line)
c) 1-10V/DALI (L = Phase, N = Neutral,
= Earthing,DA/DA = DALI control line,
Dŝ/D+ = 1-10V control line)
O
Operation with 24VDC is only permitted with a
SELV power supply suited for Class III appliances.

TO9271W0722 © WE-EF 2022
Technical specifications are
subject to change.
www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[email protected]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[email protected]
WE-EF SWITZERLAND
Switzerland
Tel [phone]
Fax [phone]
[email protected]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
[email protected]
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[email protected]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[email protected]

Surge Protection
This product features built-in surge protection circuitry in compliance
with applicable standards.
For comprehensive protection of a luminaire installation against lightning
and electrical surges,it is essential to cover mains supply and data input
lines at the distribution board level,by using respective primary (Type 1)
and secondary (Type 2) surge arrestors in compliance with EN61643-11/
IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and
activated prior to luminaire installation.Also,disconnect luminaires
before operatinghigh-power devices such as, for example,electrical
arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained
in this document for details.
WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Accessories
)ODWVXUIDFHĥWWHU
Ground Spike
&ROXPQĥWWHU
Junction box

1
Accessories
Suitability
1. FLB100 Spigot mounted
2. FLC300 Spigot mounted
3. FLD100 Spigot mounted
)ODWVXUIDFHĥWWHU 145-9535 Ground spike 310-9102
&ROXPQĥWWHU 145-9536 Junction box (Side entry) 310-9002
Junction box (Wall entry) 310-9025

2
Installation
The product must be installed and maintained by a VXLWDEO\TXDOLĥHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW
building/construction and/or electrical regulations and relevant legislation.
Warning:6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\SULRUWRLQVWDOOLQJDQGFRQQHFWLQJWKHOXPLQDLUH
Notice:,IWKHOXPLQDLUHLVPRGLĥHGE\DQ\ERG\RWKHUWKDQWKHRULJLQDOPDQXIDFWXUHUWKHQWKHZDUUDQW\
will no longer be valid and shall become the full responsibility of the modifying person/organisation.
Claims based on defects attributable to improper installation and/or application, and the consequences
thereof, are excluded.
Installation instruction of each luminaire will be separated document.
The installation on site must comply with local and/or national health and safety regulations.

3
1) Feed cable from luminaire through pivot
DQGFDEOHJODQGRIĦDWVXUIDFHĥWWHUA.
Installation Procedure
)ODWVXUIDFHĥWWHU
 'HWHUPLQHSRVLWLRQIRUĥ[LQJVFUHZVD.
Drill relevant holes Eand insert nylon plugs R.
Insert and tighten screws D.After installation
of luminaire, tighten cable gland.
Warning: Ensure not to damage any
electrical cable, water pipe or other items
drilling holes.
1) Drill screw holes Aand cable entry hole Bin
column. Ensure cable entry hole BKDVVXĩFLHQW
diameter to feed cable from luminaire.
 6HWDQGĥ[FROXPQĥWWHUCin position.
Insert and tighten screws D.
&ROXPQĥWWHU

4
2) Place ground spike Hinto the ground.1) Note: It is the responsibility to installer to
ensure the suitability of the ground spike for
VLWHVSHFLĥFFRQGLWLRQV
3) Feed cable from luminaire through pivot and cable gland I.After installation of luminaire, tighten
cable gland I.
Ground Spike

5
1) Loosen screws Kand remove cover Lfrom
body M.
4) Feed cable Sfrom luminaire through pivot of
cover L.Connect cable Rand Sto terminal
block Taccording to wiring shown in separate
luminaire installation instruction.
 'HWHUPLQHSRVLWLRQIRUĥ[LQJVFUHZVN.
Drill relevant holes Oand insert nylon plugs P.
Insert screws Nwith washers Qand tighten.
Warning: Ensure not to damage any electrical
cable, water pipe or other items drilling holes.
Junction box
2) Feed main supply cable Rthrough wall entry
or side entry of body M.
For side entry installations, replace the
pre-installed plugs with provided cable glands
as required.

6
5) After installation of luminaire,place cover Lon body Mand tighten screws K.

TO9253W0722 © WE-EF 2022
Technical specifications are
subject to change.
www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[email protected]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[email protected]
WE-EF SWITZERLAND
Switzerland
Tel [phone]
Fax [phone]
[email protected]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
[email protected]
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[email protected]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[email protected]