WE-EF FLC210 LED User manual

Surge Protection
This product features built-in surge protection circuitry in compliance
with applicable standards.
For comprehensive protection of a luminaire installation against lightning
and electrical surges,it is essential to cover mains supply and data input
lines at the distribution board level,by using respective primary (Type 1)
and secondary (Type 2) surge arrestors in compliance with EN61643-11/
IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and
activated prior to luminaire installation.Also,disconnect luminaires
before operatinghigh-power devices such as, for example,electrical
arc welders.
Installation tools
Mounting hardware used on this product
includes fasteners with hexalobular
socket heads (ISO 10664).Installation
requires the use of matching tools.
WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Projector
FLC210 LED
FLC220 LED
FLC230 LED
FLC240 LED
FLC260 LED
FLC210-CC LED
FLC220-CC LED
FLC230-CC LED
FLC240-CC LED
FLC260-CC LED
FLC210-TW LED
FLC220-TW LED
FLC230-TW LED
FLC240-TW LED
FLC260-TW LED

1
IP66, IK07, Class I, ta = 25°C
FLC240
FLC240 [EES] Version
FLC260
FLC260 [EES] Version
FLC230 [EES] Version
FLC240-CC*
FLC240-TW
FLC260-CC*
FLC260-TW
FLC230
185
FLC230-CC*
FLC230-TW
FLC220
FLC210
FLC220-CC*
FLC220-TW
Projector

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces,
no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal
circumstances or at end of life, replacement
PXVWEHFDUULHGRXWE\DVXLWDEO\TXDOLĥHGDQG
trained professional.
Warning: Do not open luminaire while mains supply is switched on.
)RURSHUDWLRQDVFRORXUFKDQJHUWKHĦRRGOLJKWVRIWKH)/&&&VHULHVUHTXLUHD'0;FRQWUROVLJQDO
(DALI on request).The operation without control signal may lead to error.
For operation withTunable White,a DALI DT8 controller is required.
Weight kg
for FLC210 4.0
for FLC220/FLC220-CC/FLC220-TW 4.3/4.3/4.3
for FLC230/FLC230-CC/FLC230-TW 7.6/7.7/7.7
for FLC240/FLC240-CC/FLC240-TW 12.6/13.8/13.8
for FLC260/FLC260-CC/FLC260-TW 17.5/18.0/18.5
Windage area m²
for FLC220 0.030
for FLC230 0.054
for FLC240 0.090
for FLC260 0.116
Tools required
– Screwdriver T-25 / T-30 (provided by WE-EF)
– Screwdriver with blade 3 x 1
Accessories:
Wireless version*
RF for FLC220/230/240/260-CC 430-0018
RF for FLC220/230/240/260-CC 430-0036
ø 5.5 – 12 mm 0.14 – 2.5 mm2
'0;3RZHU
for FLC220-CC
for FLC220-CC
for FLC230/240/260-CC
for FLC230/240/260-CC
For further information refer to separate
72:LQVWUXFWLRQIRUZLUHOHVV'0;
Do not stare at the operating light source.
For eye safety,the following requirement applies to luminaires with a colour
temperature of 4000K in combination with light beam [EE] / [EES]:
The luminaire should be positioned so that prolonged staring into the luminaire
at a distance closer than 2.8 m / 3.4 m is not expected.

3
Installation
The product must be installed and maintained by
a VXLWDEO\TXDOLĥHGSURIHVVLRQDOLQFRPSOLDQFH
with latest building/construction and/or electrical
regulations and relevant legislation.
Warning:6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\SULRUWR
installing and connecting the luminaire.
Do not stare at the operating light source.
For eye safety,the following requirement applies to
luminaires with a colour temperature of 4000 K in
combination with light beam [EE] / [EES]:
The luminaire should be positioned so that prolonged
staring into the luminaire at a distance closer than
2.8 m / 3.4 m is not expected.
Notice:,IWKHOXPLQDLUHLVPRGLĥHGE\DQ\ERG\
other than the original manufacturer,then the war-
ranty will no longer be valid and shall become the
full responsibility of the modifying person/
organisation.Claims based on defects attributable
to improper installation and/or application, and the
consequences thereof,are excluded.
The installation on site must comply with local and/
or national health and safety regulations.
Installation Procedure
 6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\1) Prior to electrical connection, proceed with
mechanical installation by securing stirrup A
to optional mounting accessory or directly
to a suitable surface.Aim luminaire in the
desired direction.
Warning: Ensure not to damage any electric
cable, water pipe or other devices while
drilling holes.
A

4
Installation Procedure
6) Connect leads of mains supply cable D(and second cable Ifor through wiring,
if required) to respective terminals in terminal block F:
a) ON/OFF or wireless version (L= Phase, N = Neutral, = Earthing)
b) 1-10 V/DALI (L = Phase,N = Neutral, = Earthing,
DA/DA = DALI control line, Dŝ/D+ = 1-10V control line).
F'0;/ 3KDVH1 1HXWUDO = Earthing, ŝ '0;FRQWUROOLQH6 6KLHOG
Tighten cable gland E.
For operation withTunable White,a DALI DT8 controller is required.
6.1))RU'0;RQO\,IWKURXJKZLULQJGDLV\FKDLQIRUWKH'0;VLJQDOLVUHTXLUHGUHPRYHUHVLVWRUR
EHWZHHQ'0;LQDQG'0;LQŅRIWHUPLQDOKDQGFRQQHFWRXWJRLQJ'0;ZLUHVLQVWHDG'RQRW
remove resistor RLIQRWKURXJKZLULQJIRUWKH'0;VLJQDOLVUHTXLUHG0LJKWFKDQJHSDFNLQJULQJLQ
FDEOHJODQGLQRUGHUWREHVXLWDEOHIRUVLQJOH'0;FDEOH
ON–OFF
1–10 V
DALI D D L1 N
L1 N
L1 N
FEI
D
Maximum luminaires per DMX bus: max.
FLC220-CC 32
FLC230-CC 32
FLC240-CC 16
FLC260-CC 10
If in any case more luminaires are required,the booster box (on request) has to be used.

5
4) Check that rating shown on luminaire label
conforms with mains electrical supply.
(example)
FLC230-LED 220-240V/50-60 Hz
;;;; 62(;;;;;;;
/('.: LWHPQR;;;
11/18 IP66
3) Remove gear box cover Bby releasing screws Cusing a Torx T-25 / T-30 tool (provided by WE-EF).
)RUZLUHOHVVYHUVLRQ3XOORĪFRQQHFWRUXof receiver Y.Do not stress the cables.
For wireless version
5) Feed mains supply cable Dthrough
cable gland E. See Fig I.
Fig I.Feed mains supply cable
through cable gland

6
For wireless version
For FLC220-CC For FLC230/240/260-CC
8) Loosen two screws Gby insert screw driver into hole J.Aim luminaire (see illustration),tighten
screws Gfirmly (max. 100 Nm).
In addition, tighten screw H(max. 6 Nm) using a Torx T-30 tool (provided by WE-EF) to secure
orientation of luminaire (not necessary for FLC220).
9) )RUZLUHOHVV'0;VROXWLRQZLWKG%DQWHQQD$WWDFKDQWHQQDWROXPLQDLUHDQGWLJKWHQZLWK
max. 1 Nm.
7) Reposition gear box cover Band retighten screws C.
For wireless version: Reconnect connector X.Ensure that the connection is tightly snapped into place.
When closing the cover, do not jam any cables.
Torque
Screw Torque
M4 max. 2.0 Nm
M5 max. 4.0 Nm
M6 max. 6.0 Nm
M8 max. 15.0 Nm
M16 max.100.0 Nm
*
*
*1 Nm

TO9255W0722 © WE-EF 2022
Technical specifications are
subject to change.
www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[email protected]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[email protected]
WE-EF SWITZERLAND
Switzerland
Tel [phone]
Fax [phone]
[email protected]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
[email protected]
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[email protected]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[email protected]