WE-EF FLD121 User manual

WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Bracket Mounted Projector
FLD121 #4 LED
FLD131 #4 LED
Surge Protection
This product features built-in surge protection circuitry in compliance with
applicable standards.
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and secondary
(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained in this
document for details.

1
IP66, Class I, ta = 40°C
Projector
FLD121 #4
FLD131 #4
Weight kg
for FLD121 #4 4.5
for FLD131 #4 5.2

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
E\DVXLWDEO\TXDOLƂHGDQGWUDLQHGSURIHVVLRQDO
Warning: Do not open luminaire while mains supply is switched on.

3
Installation Procedure
1) Switch off mains electrical supply.
 5HPRYHPRXQWLQJƃDQJHAby loosening screws B.
Detach terminal connector C.
3) 'HWHUPLQHSRVLWLRQIRUƂ[LQJVFUHZVD.
Drill relevant holes Eand insert nylon plugs F.
Warning: Ensure not to damage any electrical cable,
water pipe or other items drilling holes.
4) Feed mains supply cable G(and second cable H
for through wiring, if required) through membrane
spout(s) IZKLOHVHWWLQJPRXQWLQJƃDQJHAin
position.
 7RƂ[PRXQWLQJƃDQJHA, pierce through nylon
plugs Jby inserting and tightening screws D.
Attention: Nylon plugs Jmust remain in position to
provide sealing.
6) Check that rating shown on luminaire label conforms
with mains electrical supply.
7) Connect mains supply cable Gleads to respective
terminals in terminal connector K:
a) ON/OFF (L = Phase, N = Neutral, = Earthing)
b) 1-10 V/DALI (L = Phase, N = Neutral,
= Earthing, DA/DA = DALI control line,
D–/D+ = 1-10 V control line).
8) Ensure that all surfaces are clean and dry. Position
OXPLQDLUHRYHUPRXQWLQJƃDQJHAand attach termi-
nal connector C. Tighten screws B.
9) Loosen screws Mand Nslightly. Aim luminaire in
desired direction, retighten screws Mand N.
Attention: The luminaire is pre-assembled for
downward lighting applications as illustrated.
To aim upwards, loosen screws Pand rotate head
assembly 180 degrees. Then retighten screws.
Installation
The product must be installed and maintained by a
VXLWDEO\TXDOLƂHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW
building/construction and/or electrical regulations and
relevant legislation.
Warning: Switch off mains electrical supply prior to
installing and connecting the luminaire.
Notice:,IWKHOXPLQDLUHLVPRGLƂHGE\DQ\ERG\RWKHU
than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-
sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation
and/or application, and the consequences thereof, are
excluded.

4

5
Individual wiring
Individual wiring
Through wiring
Through wiring

TO9215W0617 © WE-EF 2017
7HFKQLFDOVSHFLƂFDWLRQVDUH
subject to change.
www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United Kingdom
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
LQIRDVLDSDFLƂF#ZHHIFRP
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]