WE-EF FLC121 User manual

Surge Protection
This product features built-in surge protection circuitry in compliance with
applicable standards.
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and secondary
(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained in this
document for details.
FFLC131 #2 LEDFLC131 #2 Lffdasfdsfadsfdsafasdfdsafdsafasdfe
FLC141 #3 LED
FLC131 #2 LED
FLC121 #2 LED
Projector
Instructions
Installation and Maintenance
WE-EF LEUCHTEN
FLC131 #3 LED
INSTALLER
HOTLINE
[phone]
7am – 7pm AEST

1
Projector
60
300
ø 105
FLC121 #2
FLC131 #2
FLC141 #3 80
ø 180
430
Weight kg
for FLC121 #2 1.7
for FLC131 #2 2.5
for FLC141 #3 4.4
ø 6.5-10.5 mm
407
for FLC131 #3 3.7
FLC131 #3
IP66, Class I/II, ta= 40°C

2
Short Post EM
EM1-2/M8 for FLC100 #2 or 3
Short Post EM
Mounting Accessories
146-0253
200
160 130
9
ESV4 for FLC100#2 or 3
Planted root
300-0461
145
145
130102
8
108
350 400
Planted root
ingress related issues!
landscaped surface and the luminaire is installed directly on the surface, warranty is void for any water
drainage. Otherwise the above mounting accessories can be used. If there is insufficient drainage on the
Note: The luminaire must be installed on an elevated concrete surface in landscape areas with poor

3
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
by a suitably qualiƂed and trained professional.
Warning: Do not open luminaire while mains supply is switched on.

4
Installation
The product must be installed and maintained by a
suitably qualiƂed professional in compliance with latest
building/construction and/or electrical regulations and
relevant legislation.
Warning: Switch off mains electrical supply prior to
installing and connecting the luminaire.
Notice: If the luminaire is modiƂed by anybody other
than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-
sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation
and/or application, and the consequences thereof, are
excluded.
The installation on site must comply with local and/or
national health and safety regulations.

5
Installation Procedure
3) Check that rating shown on luminaire label
conforms with mains electrical supply.
(example)
4) Determine positions for Ƃxing screws D.
Drill relevant holes Eand insert wall plugs F.
Warning: Ensure not to damage any electrical
cable, water pipe or other devices while drilling
holes.
2) Remove mounting ƃange Aby loosening
screws B. Detach terminal connector C.
FLC121-LED 220-240V50-60/Hz
E XXXXXXX145-XXXX SO
LED 3000K 12W item no. XXX
12/17 IP66
Switch off and isolate mains electrical supply.1)

6
6) Connect mains supply cable Gleads to
respective terminals in terminal connector C
(L = Phase, N = Neutral, = Earthing).
8) Loosen screw Mslightly. Aim luminaire in
desired direction, retighten screw M.
I
Tighten screw B.
luminaire towards object to be illuminated.
and attach terminal connector C. Turn
Position luminaire over mounting ƃange A
Ensure that all surfaces are clean and dry. 7)
ring supplied. Then tighten the pressure screw I.
cable (1.5 to 2.5mm), use the auxiliary packing
For larger cable diameters (9 to 12 mm) or TPS
H is suitable for cable diameters 7 to 9.5 mm.
tighten screws D. The pre-installed packing ring
position. To Ƃx mounting ƃange A, insert and
screw I, while setting mounting ƃange A in
Feed mains supply cable G through the pressure 5)

WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
info.asiapaciƂ[e-mail]
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]
www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[email protected]
subject to change.
Technical speciƂcations are
© WE-EF 2021
FLC100TYP23_150221_REV1
TO9206W0519
INSTALLER
HOTLINE
[phone]
7am – 7pm AEST