WE-EF FLD121 #1 Manual

WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Projector
FLD121 #1 LED
FLD131 #1 LED
Surge Protection
This product features built-in surge protection circuitry in compliance with
applicable standards.
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and secondary
(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained in this
document for details.

1
Projector
Mounting Accessories
FLD121 #1 FLD131 #1
IP66, Class I, ta = 40°C
CF-FLD1
SF-FLD1
Flat surIace Ƃtter
SF-FLD1 for FLD121/131 #1 145-9535
ColuPn Ƃtter
CF-FLD1 for FLD121/131 #1 145-9536

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
E\DVXLWDEO\TXDOLƂHGDQGWUDLQHGSURIHVVLRQDO
Warning: Do not open luminaire while mains supply is switched on.

3
Installation
The product must be installed and maintained by a
VXLWDEO\TXDOLƂHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW
building/construction and/or electrical regulations and
relevant legislation.
Warning: Switch off mains electrical supply prior to
installing and connecting the luminaire.
Notice:,IWKHOXPLQDLUHLVPRGLƂHGE\DQ\ERG\RWKHU
than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-
sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation
and/or application, and the consequences thereof, are
excluded.
The installation on site must comply with local and/or
national health and safety regulations.

4
1) Switch off mains electrical supply.
Installation Procedure
Installation tFlat surIace Ƃtter
 'HWHUPLQHSRVLWLRQVIRUƂ[LQJVFUHZVD.
Drill relevant holes Q and insert nylon plugs R.
Insert and tighten screws D.
Warning: Ensure not to damage any electrical
cable, water pipe or other items drilling holes.
4) Loosen screw MRQVOLSƂWWHUH(do not turn it
RXWXQWLOVSOLSƂWWHUFDQEHRSHQHG&RQQHFW
luminaire AZLWKƃDWVXUIDFHƂWWHU T by sliding
VOLSƂWWHUHover pivot I, while pulling luminaire
cable Cthrough hole Land turning luminaire A
WRZDUGVREMHFWWREHLOOXPLQDWHG(QVXUHVOLSƂW-
ter His properly seated on pivot I, then tighten
screw M.
2) Detach strain relief clip KIURPƃDWVXUIDFH
ƂWWHUT.
Attention: Keep strain relief clip Kfor
locking cable later (in step 5).
Feed cable Cfrom luminaire Athrough pivot
I and hole LRIƃDWVXUIDFHƂWWHUT.

5
5) Clamp strain relief clip Kon cable Cand press
into hole L RIƃDWVXUIDFHƂWWHUT. Ensure the
strain relief clip Kis properly placed in position
to lock the cable.
7) Connect leads of luminaire cable Cand main
supply cable Gto respective terminals of
socket Sin connecting box J:
a) ON/OFF (L = Phase, N = Neutral,
= Earthing)
b) 1-10 V/DALI (L = Phase, N = Neutral,
= Earthing, DA/DA = DALI control line,
D–/D+ = 1-10 V control line).
Attention: (QVXUHFRQQHFWLQJER[LVƂUPO\
tightened for proper sealing.
6) Check that rating shown on luminaire label
conforms with mains electrical supply.
(example)
FLD121-LED 220-240V50-60/Hz
145-XXXX SOE XXXXXXX
LED 3000K 12W item no. XXX
04/19 IP66
8) Loosen screws Nand Oslightly. Then aim
luminaire in desired direction and tighten
screws Nand O.

6
1) Switch off mains electrical supply.
Installation Procedure
Installation tColuPn Ƃtter
6XLWDEOHIRUFROXPQGLDPHWHUŰPP6HUYLFHGRRURQFROXPQKDVWREHSURYLGHGIRUFDEOHWHUPLQDWLRQ
PD[LPXPPIURPFROXPQƂWWHUPRXQWLQJSRVLWLRQ
 6HWDQGƂ[FROXPQƂWWHUBin position.
Insert and tighten screws D.4) Loosen screws MRQVOLSƂWWHUH(do not turn out) XQWLOWKHVOLSƂWWHUFDQEHRSHQHG
 'HWHUPLQHSRVLWLRQIRUƂ[LQJVFUHZVDand
cable entry hole F. Drill relevant holes Eand F
on column X. Ensure cable entry hole Fhas
VXIƂFLHQWGLDPHWHUWRIHHGFDEOHIURPOXPLQDLUH

7
5) Feed cable Cfrom luminaire Athrough pivot I
on column X, while connecting luminaire A
ZLWKFROXPQƂWWHUBE\VOLGLQJVOLSƂWWHUHover
pivot I. Turn luminaire Atowards object to
EHLOOXPLQDWHG(QVXUHVOLSƂWWHUHis properly
seated on pivot I, then tighten screw M.
7) Connect leads of luminaire cable Cand main
supply cable Gto respective terminals of
socket Sin connecting box J:
a) ON/OFF (L = Phase, N = Neutral,
= Earthing)
b) 1-10 V/DALI (L = Phase, N = Neutral,
= Earthing, DA/DA = DALI control line,
D–/D+ = 1-10 V control line).
Attention: (QVXUHFRQQHFWLQJER[LVƂUPO\
tightened for proper sealing.
8) Loosen screws Nand O slightly. Then aim
luminaire in desired direction and tighten
screws Nand O.
6) Check that rating shown on luminaire label
conforms with mains electrical supply.
(example)
FLD121-LED 220-240V50-60/Hz
145-XXXX SOE XXXXXXX
LED 3000K 12W item no. XXX
04/19 IP66

www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United Kingdom
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
LQIRDVLDSDFLƂF#ZHHIFRP
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]
TO9210W0419 © WE-EF 2019
7HFKQLFDOVSHFLƂFDWLRQVDUH
subject to change.