Weather Guard ITEMIZER 314 Instruction manual

DANGER
Danger of explosion. Do not use this product for storing or
transportingflammables,explosives,hazardousmaterials,
orhazardouswaste,suchascontainersofgasoline,solvents,
gunpowder,dynamite,propanetanks,acetylenetanksand
cutting torches. This product is only intended and safe for
use in storing and transporting small tools, equipment and
othersimilarmaterials. Any modifications madeto,or unin-
tendeduse ofthis product, could create a hazardous condi-
tion that can cause death, serious personal injury or property
damage.
ASSEMBLY AND INSTALLATION INSTRUCTIONS
ITEMIZER® Aluminum Drawer Units
Models 314 • 316 • 317 • 318 • 326 • 327 • 328
Part No. 24-0300 REV. E ECN 5315 05/13
Figure1.AluminumDrawer
UnitsShownStacked
IMPORTANT
BEFOREYOUBEGIN
Read these instructions and
warnings completely before
installation.
TOOLS REQUIRED
•Drill with 5/16" & 13/32" drill bits
•7/16" Open or Box End Wrench (2)
•9/16" Open or Box End Wrench
BOLT KIT
BoltKit#32-0314is providedwith
your Drawer Unit. Check this bolt
kit to be sure the following parts
areincluded:
Quan. Description
6 1/4-20 x 3/4" Hex Hd. Bolt
4 1/4-20BlindFasteners
10 1/4" Flat Washers
6 1/4" Lock Washer, ext. tooth
1 1/4-20 x 2-1/4" Bolt, blk. ox.
1 InstallationTool
4 1/4-20 Nylon Lock Nuts
PARTS LIST
1-DrawerUnit
2-Mounting Brackets
6-Dividers(perdrawersection)
Approximate Assembly and
Installation Time:
48 min. per unit (0.8 hrs.)
Depending on Van equipment
installation experience.
1

INSTALLATION INSTRUCTIONS 1. Position the lower Drawer Unit in the vehicle, making sure the obround holes in the front skids are on top of the floor ribs (as shown in Figure 2.). Mark the floor through the obround holes. 2. Go to the rear of the drawer unit (see Figure 3.) and place the Mounting Brackets, as shown, with the longest side against the top of the floor rib. Mark through both sets of holes to the floor and the rear skid. 3. Remove the drawer unit, drill the marked locations floor ribs for installation of four Blind Fasteners. Follow Blind Fasteners installation instructions listed on the back page. 4. Drill the marked locations in the rear skid. Install the Mounting Bracket to the rear skid. 5. Replace the drawer unit into the vehicle and fasten. STACKING INSTRUCTIONS 6. Place the upper Drawer Unit on top of the previously installed lower unit. Align with the front of the lower unit (see Figure 2.). Mark through the front skid obround holes to the lower unit. 7. Move the rear of the unit (see Figure 3) and place the long end of the Mounting Bracket into the open end of the rear skid. With the short end facing down, mark through the hole to the side of the lower unit. 8. Remove the upper drawer unit and drill the rear holes in the side of the lower unit. Drill the front skid holes and install Blind Fasteners. 9. Replace the upper unit and fasten.
WARNING
All floor mounting bolts near the gas tank area should be installed from the underside of the vehicle, to guard against the gas tank being punc-tured inthe event ofa collision. This would mean not using Blind Fasteners in this area. Holes drilled in this area should be 5/16".
WARNING
CAUTION
To keep debris out of your eyes when checking the underside of the vehicle, or when drilling, always wear protective eyewear.
Prior to drilling, so as not to cut or puncture fuel tanks, fuel lines, brake lines, electric wires, etc., check under vehicle for locations.
Figure 3. Rear Mounting
1/4-20 Blind Fastener
1/4-20 x 3/4" Hex Hd. Bolt
1/4" External Tooth LockWasher
1/4" Flat Washer
1/4-20 x 3/4" Hex Hd. Bolt 1/4" External Tooth
LockWasher
1/4" Flat Washer
13/32" Hole 13/32" Hole
1/4" External Tooth LockWasher
Mounting Bracket
1/4-20 Blind Fastener
13/32" Hole
5/16" Hole
1/4" Flat Washer
1/4-20 x 3/4" Hex Hd. Bolt
1/4" Flat Washer
1/4-20 x 3/4" Hex Hd. Bolt
1/4"External Tooth Lock Washer
1/4" Flat Washer
1/4-20 Nut
1/4"External Tooth Lock Washer
1/4-20 x 3/4"
Hex Hd. Bolt
1/4" Flat Washer
Mounting Bracket
1/4-20 Blind Fastener
13/32" Hole
Figure 2. Front Mounting
2

If you have any questions, please give us a call. Call Toll Free 1-800-456-7865
WEATHER GUARD® products are protected by one or more of the following trademarks:
U.S.- 842268,1661625, 1663369,1734659,2228051,2362167; Canada- 282725;U.K. -1400720;N.Z.-296049;Aus.- 761964
KNAACKLLC
420E.TERRA COTTA AVENUE - CRYSTAL LAKE, ILLINOIS,USA60014
815-459-6020
©2001KnaackLLC
-NOTICE-
Anymodificationorunintendeduseofthisproductshallimmediately void all manufacturerswarranties.
Manufacturer disclaims all liability for injuries to persons or property resulting from any modification to, or
unintendeduse ofthis product.
WARNING
Prior to drilling, so as not to
cut or puncture fuel tanks, fuel
lines, brake lines, electric
wires,etc., check under vehi-
cle for locations.
NOTE - Becarefulwhendrilling,or in-
stalling Blind Fastener, to ensure that
thereisenoughclearancebehindthe
surface so as not to damage the outer
skinof thevehicle, roofmembers or
vehiclecomponents.
Black
Oxide
Bolt
Flat
Washer
9/16”
Wrench
Installation
Tool
Blind
Fastener
INSTALLATION PROCEDURE
USING BLIND FASTENERS
Place a drop of oil on the black oxide
boltbeforeassembling asshownon
right. Place the Blind Fastener in the
hole and use a 1/2” or 7/16” wrench to
tighten black hex bolt until the blind
fastener is fully seated. When setting
black hex bolt, it will start out hard.
As the Blind Fastener “bulbs” out it
will get easier, until it bottoms out or
sets. Make sure the Blind Fastener
andInstallationTooldonotturnduring
installation.
3Part No. 24-0300 REV. E ECN 5315 05/13