Weber mt CR 3-II Hd Operating instructions

CR 3-II Hd
0116144
0116145
Operating and
Maintenance Manual

2
1
2
3
4
56
Attached to the machine is a rating plate. Note down the information given on this plate so that
you can recreate the rating plate should the plate be lost.
1 Description 2 Type
.................................................... ...................................................
3 Serial number 4 Year of construction
.................................................... ....................................................
5 Mass [kg] 6 Rated power [kW]
.................................................... ....................................................

3
Contents
1. Introduction..................................................................................................................... 4
2. Description...................................................................................................................... 5
3. Technical data................................................................................................................. 6
4. Safety............................................................................................................................... 7
4.1. Information and safety stickers ........................................................................... 12
5. Operation....................................................................................................................... 13
6. Transport....................................................................................................................... 18
7. Storage .......................................................................................................................... 18
8. Maintenance.................................................................................................................. 19
8.1. Maintenance overview .............................................................................................. 20
8.2. Description of the maintenance operations............................................................ 21
8.2.1. Check the engine oil level ................................................................................ 21
8.2.2. Change the engine oil ...................................................................................... 21
8.2.3. Clean the air lter............................................................................................. 22
8.2.4. Check the hydraulic oil level ............................................................................ 23
8.2.5. Change the oil in the exciter ............................................................................ 23
8.2.6. Check V-belt..................................................................................................... 23
8.2.7. Adjust / replace the spark plug.......................................................................... 24
8.3. Operating uids and ll levels ................................................................................. 25

4
1. Introduction
This operating and maintenance manual is designed to help
you become familiar with your soil compactor and enable you
to maintain it and use it for its intended purpose.
The safety and maintenance instructions provided in this
manual will help avoid hazards, reduce repair and downtime
costs and will increase the reliability and operational readiness
of your machine. Follow these instructions precisely.
This operating and maintenance manual must always be kept
at the implementation site of the machine and be available to
the machine operator.
Enclosed with this manual is a valid declaration of conformity
and a spare parts lists for orders of spare parts. Store these
documents carefully.
If you require any additional information, turn to your
Weber MT dealer.
Found on the last page of this manual is a QR code. Scan it to
acquire the current contact addresses of all Weber MT branches.
You can obtain information on the assembled Honda gasoline
engine and the associated operating and maintenance
manual as well as the spare parts list, if needed,
at www.honda-engines-eu.com

5
The machine is a hand-guided, reversible soil compactor.
The machine is composed of a bottom and a top section.
The bottom section houses the exciter, while the top section
contains the engine and the required controls.
An air-cooled Honda gasoline engine makes the exciter
vibrate via a centrifugal clutch. The generated force is
transmitted between top and bottom section via a V-belt.
The engine speed is adjusted between idle speed and
full-throttle speed via a gas lever.
Forward and reverse travel is variably controlled with
a handle via a hydraulic system.
2. Description
The machine

6
3. Technical data
CR 3-II Hd
Weight
Operating weight CECE [kg] 203
Dimensions
Overall length [mm] 1350
Overall width / with attachment
plates [mm] 500/600/700
Height with folded guide bar [mm] 1060
Base plate length [base in mm] 350
Pressure surface [mm] 500x350
Drive
Engine manufacturer Honda
Type GX 270
Performance at operating speed in
accordance with ISO 3046-1 [kW] 5.1
Combustion process 4-stroke gasoline
Operating speed [1/min] 3000
Operating speed
[soil-dependent, m/min] 20
Incline capacity [soil-dependent, %] 35
Vibration
System Two-shaft vibrator
Drive concept Mechanical
Frequency [Hz] 80
Centrifugal force [kN] 35
Noise emissions in accordance
with 2000/14/EC
Sound pressure level LPA
ascertained in accordance
with EN 500, [dB (A)] 98
Sound power level LWA
ascertained in accordance with
EN ISO 3744 and EN 500, [dB (A)] 108
Vibration values
Root-mean-square acceleration
value for hand-arm vibration
ascertained in accordance with
EN 500, [m/s²] 2.0
In accordance with directive
2006/24/EC, complying with the
vibration values is the owner’s
responsibility

7
4. Safety
General All safety instructions must be read and complied with,
as non-compliance will result in
– danger to life and limb of the user,
– impairments to the machine or other property.
In addition to the operating manual, the accident-prevention
regulations in the country where the appliance is used
must be complied with.
Intended use
Non-intended use
Residual risk There is always an increased risk of accidents in the imme-
diate danger area around the machine if the operator fails to
notice persons in the vicinity of the machine.
Anyone close to the machine must be made aware of this risk.
The operator must not put the machine into operation unless
everyone in the vicinity of the machine is aware of this risk.
The machine should only be used in technically faultless
condition, as intended, in a safety-conscious and hazard-
conscious manner, and in compliance with the instructions
in the operating manual.
Malfunctions that may impair safety require that you stop
working with the machine immediately. These types of
damage must be reported and corrected without delay.
The machine is designed exclusively for compacting:
– sand,
– gravel,
– crushed rock,
– low-cohesive mixed material,
– asphalt,
– paved surfaces.
The operator’s work position is behind the machine.
The operator must guide the machine safely with both
hands on the handle.
Unless used as intended, the machine involves a risk of per-
sonal injury and property damage. The machine is expressly
not suitable for:
– compacting frozen subsurfaces,
– compacting hard soils that cannot be compacted further,
– compacting non-bearing material,
– compacting highly cohesive soils,
– compacting (ramming) that exerts point loads on
the base plate,
– crushing and compacting individual rocks.
The responsibility for any damage arising from non-intended
use falls on the owner / operator.
Non-intended use or misuse will void all liability and warranty
claims.

8
Requirements on the operator
Personal protective equipment Personal protective equipment consisting of
– hard hat,
– hearing protection,
– protective gloves,
– work shoes or boots with toe guard
must be worn during operation and the execution of
maintenance on the machine.
Danger areas The immediate danger area is the direct perimeter around
the machine. This area is o󰀨-limits to third parties.
Spare parts, changes
and conversions
Changes and conversions are prohibited unless made with
original Weber MT spare parts. If the machine is modied
with other accessories without the approval of Weber MT,
the manufacturer will not assume liability for any resulting
personal injury or property damage.
All maintenance and repairs must be carried out with original
Weber MT spare parts. Untested spare parts may a󰀨ect
the reliability and safety of the machine.
Before starting the machine There is danger of material damage if the machine is started
before necessary maintenance or repairs have been completed.
Make sure every time before starting the machine that all work
on the machine has been completed.
To avoid injuries, the machine must not be started unless the
operator wears the required personal protective equipment.
Objects placed on top of the machine may fall or be ung o󰀨
during operation or when the machine is started. Therefore,
remove all loose objects or tools before starting the machine.
If the gas cap is open, fuel may escape and ignite on the
engine when the machine is started or while it is operating.
There is a risk of burns. Therefore, do not start the machine
unless the gas cap is closed.
This soil compactor may only be operated by suitable oper-
ators who are 18 years or older. They must be instructed on
how to operate the machine by the owner or by the owner’s
assigned personnel. The operator must comply with tra󰀩c
regulations.
The machine must not be operated by children.

9
Start-up procedure Do not disperse any sprays or other agents into the air intake
while the machine is starting up. They may lead to overheating
in the combustion chamber and result in damage to the engine.
There is danger of su󰀨ocation if the operator starts up
the machine in closed rooms or in deep and tight trenches.
Operating the machine in closed rooms is prohibited. Provide
for an adequate supply of air before starting the machine.
During operation Monitor the surroundings to avoid injury to third parties
or material damage.
Suspend operation and shut down the machine if detecting
damage on the machine during operation.
Parking the machine Always park the machine on a level subsurface with su󰀩cient
bearing capacity.
Parked machines presenting an obstacle must be secured
in accordance with statutory regulations, particularly in
the area of public tra󰀩c surfaces.
Engine and exhaust heat up during operation and can cause
burns on contact. Therefore, do not touch these components
during operation or shortly after the machine was switched o󰀨.
Fueling the machine Spilled fuel may ignite and has a negative impact on the
environment. Therefore, wipe up spilled fuel and make sure
the gas cap is rmly tightened after fueling.
When coming into contact with fuels, the rubber-bonded metal
bu󰀨ers of the machine may become damaged or ine󰀨ective.
Therefore, wipe spilled fuel carefully o󰀨 the rubber-bonded
metal bu󰀨ers.
Fuel vapors are easily ammable. Do not smoke and
keep away from open re while refueling the machine.
The machine must not be fueled unless the engine is
switched o󰀨.

10
Cleaning work Use clear water for cleaning. Do not use ammable solvents.
The vapors of the solvents may ignite upon contact with hot
components or other sparks.
Perform cleaning tasks only in rooms that are suitable and
have been approved for that purpose. Residual oil and lubri-
cants that may have been rinsed o󰀨 have a negative impact
on the environment and must be collected by suitable means
(e.g. oil separator).
Safe handling of combustion
engines
Combustion engines pose a particular risk during operation.
Their exhaust emissions contain carbon monoxide, a colorless
and odorless gas that is extremely hazardous, which, if inhaled
even briey, can cause unconsciousness and death.
Therefore, never inhale the exhaust gas.
Inspection The machine must be inspected in accordance with the corre-
sponding implementation conditions and operating conditions
to ensure its operationally safe status. This inspection should
be performed as needed by an expert – however, no less than
once a year. The ndings of the inspection must be stored in
writing until the time of the next inspection.

11
Safety instructions
and warnings
A variety of safety instructions and warnings are used
throughout this operating manual.
The following explains the meaning of signal words
and symbols.
ATTENTION warns of
the danger of material
damage.
CAUTION warns of the
danger of slight injury.
WARNING warns of
a danger that may lead to
death or serious injury.
DANGER warns of
a danger that will lead to
death or serious injury
unless avoided.
ATTENTION
CAUTION
WARNING
DANGER
The information symbol provides supplemental
information on the operation of the machine and
points to complementary technical information.

12
4.1. Information and safety stickers
Sticker Meaning
1
All threaded unions must
be checked for rm seat on
a regular basis and, particularly,
after initial use.
2The fuel tank may only be fueled
with regular gasoline.
3
Use the designated lifting
ring to lift the machine.
Sound power level 108 dB (A),
wear ear protection.

13
5. Operation
Preparing the machine
for initial use
Remove all packaging material.
Check all components for visible damage.
Do not start the machine if detecting visible damage.
Contact the responsible dealer.
Check if the shipment of the machine and its components
is complete.
Check the ll level of the operating uids and top o󰀨
if necessary.
Set up the machine at its place of use.

14
1
2
3
4
5
6
7
8
Operating positions on the machine
Overall view CR 3
1 Base plate with exciter
2 Gas lever
3 Handle
4 Lock for the guide bar
5 Lifting ring
6 Engine
7 Reversing starter
8 Carburetor with choke and fuel cock

15
1
2
Before starting work
Perform the following tasks before starting to work in order to
prevent failures or excessive wear.
Visual inspections Hydraulic line for leaks
Fuel system for leaks
Rubber bu󰀨ers for crack formation
Other damage
Check and, if necessary,
correct the ll levels
Engine oil
Hydraulic oil
Fuel
Other inspections Check all threaded unions for rm seat
Verify compliance with the maintenance schedule

16
Working with the machine
Starting the engine
WARNING
Danger of su󰀨ocation from engine exhausts when starting
the engine in closed rooms or poorly ventilated work areas.
Start the engine only in well-ventilated environments.
See section “Safety” for operating the machine in trenches.
ATTENTION
Risk of engine damage. The use of starter spray may lead to
overheating in the combustion chamber.
Do not use any starter spray.
Adjust the desired work height of the guide bar with
the set screw (1).
Set the short-circuit switch (2) to “I”.
Open the fuel cock (slide to the right).
Close the choke lever (slide to the left).
Bring the gas lever into the full-throttle position.
Slowly pull the handle of the reversing starter until
resistance (the compression of the engine) is noticeable.
Allow the handle to glide back into the initial position.
Pull the handle through quickly, forcefully and completely.
Repeat the process if the engine does not start.
Set the gas lever to idle speed.
Allow the engine to warm up for a few minutes.
Open the choke lever (slide to the right).
The machine is ready for operation.

17
ATTENTION
Danger of material damage or excessive wear if V-belt slips
through.
Operate the machine only in full-throttle mode.
CAUTION
Risk of injury if the machine is guided improperly.
Guide the machine safely with both hands on the handle.
CAUTION
There is a crushing hazard between the machine and the wall
during work in close proximity to walls.
Use extra caution when working close to obstacles.
Compacting
Start the engine.
Bring the gas lever into the full-throttle position.
Switch between forward and reverse travel by setting
the handle to the corresponding direction.
Switching o󰀨 the engine
Bring the gas lever into the idle speed position.
Close the fuel cock (slide to the left).
Set the short-circuit switch to “0”.
The forward and reverse travel of the machine is
innitely variable.
The speed of the machine is selected with the
corresponding deection of the handle

18
6. Transport
Lifting the machine The machine can be lifted for loading onto a vehicle.
CAUTION
Risk of material damage and injuries. The use of defective or
unsuitable lifting gear may cause the machine to fall down.
Use slings that possess the appropriate carrying capacity.
Lock the guide bar in place in the folded position.
Fit the crane hook into the lifting ring and lift the machine up
straight.
Storage for an extended
period
If the machine will not be used for a period longer than
one month, the following measures must be taken:
Clean the entire machine thoroughly.
Check the entire machine for leaks. Correct any detected
defects.
Empty fuel and ll the tank with clean fuel.
Check and, if necessary, correct the engine oil level.
Check and clean air and fuel lter. Replace if damaged.
Lightly oil all bare parts, levers and accelerator
control cables.
If the machine is to be stored for longer than six
months, contact the Weber MT’s service organization
to discuss additional measures.
7. Storage
Storage at the
construction site
If stored at the construction site, e.g. over night, the machine
must be secured against theft and unauthorized use.
Parked machines presenting an obstacle must be secured
in accordance with statutory regulations, particularly in
the area of public tra󰀩c surfaces.

19
8. Maintenance
General information The section below contains instructions that need to be
observed for regular maintenance. Read these instructions
carefully and follow them in order to prevent downtimes of the
machine caused by excessive wear or damage to the machine.
Also read the safety instructions relevant to machine
maintenance before you begin with the maintenance work.
They help minimize the risk to maintenance personnel.
Maintenance personnel Maintenance and repairs require specic qualications. These
operations may only be carried out by trained professionals.
Maintenance personnel must be instructed on how to operate
the machine by the owner or by the owner’s assigned
personnel.
Maintenance personnel are required to wear the personal
protective equipment during work (see section “Safety”).
Safety There is an increased risk of injury during maintenance
and repairs, e.g. crushing at moving parts.
Following the conclusion of all maintenance and repairs,
all protective xtures must be retted and placed back
into operation.
Discharged operating uids have a negative impact on the
environment. They must be collected and stored in suitable
containers. Disposal in accordance with environmental
protection regulations.
All maintenance work may only be carried out when the
engine is cold. Safeguard the engine against unauthorized
start attempts.
Before working on the electrical system, disconnect the starter
battery and cover the battery terminals with insulating material.
It is also recommended to disconnect the battery as a means
to safeguard the machine against unauthorized start attempts
during maintenance work.
Before starting the machine after maintenance operations,
make sure that all loose parts (screws, tool, etc.) have been
removed from the machine. They may be drawn in or ung o󰀨
by moving parts.
Keep the entire machine clean. The stickers must always
be clearly legible. Damaged stickers must be replaced.

20
8.1. Maintenance overview
Frequency
Initial maintenance /
after 10 operating
hours
Every 8 operating
hours / daily
Every 50 operating
hours / every six
months
Every 150 operating
hours / every year
See section
Activity
Change the engine oil XX8.2.2
Check the valve play of the
engine, adjust if necessary XHonda instructions
Re-tighten all accessible
threaded connections X
Clean the air lter X8.2.3
Change the fuel lter XHonda
instructions
Check the oil level of
the transmission X X 8.2.4
Change the oil in the exciter X8.2.5
The regulations and the operating and maintenance manuals of the engine
manufacturer must be complied with in addition to the activities specied in
the above maintenance overview.