Weber mt CR 9-II Hd E Operating instructions

Operating and
Maintenance Manual
CR 9-II Hd E
CR 9-II Hd CCD
0116830
0116831

2
1
2
3
4
56
1 Designation 2 Type
.................................................... ...................................................
3 Serial no. 4 Year of construction
.................................................... ....................................................
5 Weight 6 Rated power kW
................................................... .....................................................
Attached to the machine is a rating plate. Note down the information given on this plate so that you
can recreate the rating plate should the plate be lost.

3
Contents
1. Introduction..................................................................................................................... 4
2. Description...................................................................................................................... 5
3. Technical data................................................................................................................. 6
4. Safety............................................................................................................................... 7
4.1. Information and safety stickers ........................................................................... 12
5. Operation....................................................................................................................... 13
6. Transport....................................................................................................................... 21
7. Storage .......................................................................................................................... 21
8. Maintenance.................................................................................................................. 22
8.1. Maintenance overview .............................................................................................. 23
8.2. Description of the maintenance operations............................................................ 24
8.2.1. Check the engine oil level ................................................................................ 24
8.2.2. Change the engine oil ...................................................................................... 24
 8.2.3.Changetheengineoillter .............................................................................. 25
 8.2.4.Cleantheairlter............................................................................................. 26
8.2.5. Change the oil in the exciter ............................................................................ 26
8.2.6. Check the hydraulic oil level ............................................................................ 27
8.2.7. Adjust / replace the spark plug......................................................................... 27
8.2.8. Check V-belt..................................................................................................... 28
 8.2.9.Replacethefuellter ....................................................................................... 28
8.2.10. Change the fuses........................................................................................... 29
8.2.11. Use a permanent charger .............................................................................. 29
8.3. Operating uids and ll levels ................................................................................. 30

4
This operating and maintenance manual is designed to help
you become familiar with your soil compactor and enable you
to maintain it and use it for its intended purpose.
The safety and maintenance instructions provided in this
manual will help avoid hazards, reduce repair and downtime
costs and will increase the reliability and operational readiness
of your machine. Follow these instructions precisely.
This operating and maintenance manual must always be kept
at the implementation site of the machine and be available to
the machine operator.
If you require any additional information, turn to your
Weber MT dealer.
Found on the last page of this manual is a QR code. Scan
it to acquire the current contact addresses of all Weber MT
branches.
You can obtain information on the assembled Honda gasoline
engine and the associated operating and maintenance manual
as well as the spare parts list, if needed, at
www.honda-engines-eu.com
You can obtain the current spare parts list of the machine in
the WeberMT Service App or use the link below:
1. Introduction
https://www.webermt.com/DE/deu/ersatzteillistenspare-partscr-6-cr-9/cr-9/

5
2. Description
The machine The machine is a hand-guided, reversible soil compactor.
The machine is composed of a bottom and a top section.
The bottom section houses the exciter, while the top section
contains the engine and the required controls.
An air-cooled Honda gasoline engine makes the exciter vibrate
via a centrifugal clutch. The generated force is transmitted
between top and bottom section via a V-belt.
The engine speed is adjusted between idle speed and
full-throttle speed via a gas lever.
Forward and reverse travel is variably controlled with a handle
via a hydraulic system.

6
3. Technical data
CR 9-II Hd E CR 9-II Hd CCD
Weight
Operating weight CECE [kg] 670 671
Dimensions
Overall length [mm] 1867 1867
Overall width/with attachment plates
[mm] 650/750/900 650/750/900
Height with folded guide bar [mm] 1167 1167
Base plate length [base in mm] 450 450
Pressure surface [mm] 450x750/450x900 450x750/450x900
Drive
Engine manufacturer Honda Honda
Type GX630 GX630
Performance at operating speed in
accordance with ISO 3046-1 [kW] 10.5 10.5
Combustion process 4-stroke gasoline 4-stroke gasoline
Operating speed [1/min] 2900 2900
Operating speed [soil-dependent,
m/min] 28 28
Incline capacity [soil-dependent, %] 35 35
Vibration
System Two-shaft vibrator Two-shaft vibrator
Drive concept mechanical mechanical
Frequency [Hz] 65 65
Centrifugal force [kN] 100 100
Noise emissions in accordance
with 2000/14/EC
Sound pressure level LPA
ascertained in accordance with EN
500, [dB (A)]
91 91
Sound power level LWA ascertained
in accordance with EN ISO 3744
and EN 500, [dB (A)]
109 109
Vibration values
Root-mean-square acceleration
value for hand-arm vibration
ascertained in accordance with EN
500, [m/s²]
2.4 2.4
In accordance with directive
2006/24/EC, complying with the
vibration values is the owner's
responsibility

7
4. Safety
General All safety instructions must be read and complied with, as
non-compliance will result in
- Danger to life and limb of the user,
- Impairments to the machine or other property.
In addition to the operating manual, the accident-prevention
regulations in the country where the appliance is used must be
complied with.
Intended use
Non-intended use
Residual risk There is always an increased risk of accidents in the
immediate danger area around the machine if the operator
fails to notice persons in the vicinity of the machine.
Anyone close to the machine must be made aware of this risk.
The operator must not put the machine into operation unless
everyone in the vicinity of the machine is aware of this risk.
The machine should only be used in technically faultless
condition, as intended, in a safety-conscious and
hazard-conscious manner, and in compliance with the
instructions in the operating manual.
Malfunctions that may impair safety require that you stop
working with the machine immediately. These types of damage
must be reported and corrected without delay.
The machine is designed exclusively for compacting:
- Sand,
- Gravel,
- Crushed rock,
- Low-cohesive mixed material,
- Paved surfaces.
The operator's work position is behind the machine.
The operator must guide the machine safely with both hands
on the handle.
Unless used as intended, the machine involves a risk of
personal injury and property damage. The machine is
expressly not suitable for:
- Compacting frozen subsurfaces,
- Compacting hard soils that cannot be compacted
further,
- Compacting non-bearing material,
- Compacting highly cohesive soils,
- Compacting (ramming) that exerts point loads on the
base plate,
- Crushing and compacting individual rocks.
The responsibility for any damage arising from non-intended
use falls on the owner / operator.
Non-intended use or misuse will void all liability and warranty
claims.

8
Requirements on the operator
Personal protective equipment Personal protective equipment consisting of
- Hard hat,
- Hearing protection,
- Protective gloves,
- Work shoes or boots with toe guard
must be worn during operation and the execution of
maintenance on the machine.
Danger areas The immediate danger area is the direct perimeter around the
machine.Thisareaiso󰀨-limitstothirdparties.
Spare parts, changes and
conversions
Changes and conversions are prohibited unless made with
originalWeberMTspareparts.Ifthemachineismodied
with other accessories without the approval of Weber MT, the
manufacturer will not assume liability for any resulting personal
injury or property damage.
All maintenance and repairs must be carried out with original
WeberMTspareparts.Untestedsparepartsmaya󰀨ectthe
reliability and safety of the machine.
Before starting the machine There is danger of material damage if the machine is
started before necessary maintenance or repairs have been
completed. Make sure every time before starting the machine
that all work on the machine has been completed.
To avoid injuries, the machine must not be started unless the
operator wears the required personal protective equipment.
Objectsplacedontopofthemachinemayfallorbeungo󰀨
during operation or when the machine is started. Therefore,
remove all loose objects or tools before starting the machine.
If the gas cap is open, fuel may escape and ignite on the
engine when the machine is started or while it is operating.
There is a risk of burns. Therefore, do not start the machine
unless the gas cap is closed.
This soil compactor may only be operated by suitable
operators who are 18 years or older. They must be instructed
on how to operate the machine by the owner or by the owner's
assignedpersonnel.Theoperatormustcomplywithtra󰀩c
regulations.
The machine must not be operated by children.

9
Start-up procedure Do not disperse any sprays or other agents into the air intake
while the machine is starting up. They may lead to overheating
in the combustion chamber and result in damage to the
engine.
Thereisdangerofsu󰀨ocationiftheoperatorstartsupthe
machine in closed rooms or in deep and tight trenches.
Operating the machine in closed rooms is prohibited. Provide
for an adequate supply of air before starting the machine.
One electronic start procedure must not last longer than 5
seconds to avoid damage to the engine. Pause for at least 10
seconds before repeating the start procedure.
If the ignition key fails to spring back to position “1” by itself,
the electric starter and the engine may sustain damage. Abort
the start procedure and shut down the machine. Identify and
rectify the cause before the next start attempt.
During operation Monitor the surroundings to avoid injury to third parties or
material damage.
Suspend operation and shut down the machine if detecting
damage on the machine during operation.
Stop operation and shut down the machine if the light
indicators of the start module do not go out shortly after startup
or come on during operation.
The symbol is lit permanently during operation. It signals
that the engine is running. Refer to the section “Operation” for
the exact meaning of the individual light indicators.
Parking the machine Alwaysparkthemachineonalevelsubsurfacewithsu󰀩cient
bearing capacity.
Parked machines presenting an obstacle must be secured in
accordance with statutory regulations, particularly in the area
ofpublictra󰀩csurfaces.
Engine and exhaust heat up during operation and can cause
burns on contact. Therefore, do not touch these components
duringoperationorshortlyafterthemachinewasswitchedo󰀨.
Fueling the machine Spilled fuel may ignite and has a negative impact on the
environment. Therefore, wipe up spilled fuel and make sure
thegascapisrmlytightenedafterfueling.

10
Cleaning work Useclearwaterforcleaning.Donotuseammablesolvents.
The vapors of the solvents may ignite upon contact with hot
components or other sparks.
Perform cleaning tasks only in rooms that are suitable and
have been approved for that purpose. Residual oil and
lubricantsthatmayhavebeenrinsedo󰀨haveanegative
impact on the environment and must be collected by suitable
means (e.g. oil separator).
Safe handling of combustion
engines
Combustion engines pose a particular risk during operation.
Their exhaust emissions contain carbon monoxide, a colorless
and odorless gas that is extremely hazardous, which, if inhaled
evenbriey,cancauseunconsciousnessanddeath.
Therefore, never inhale the exhaust gas.
Inspection The machine must be inspected in accordance with the
corresponding implementation conditions and operating
conditions to ensure its operationally safe status. This
inspection should be performed as needed by an expert
-however,nolessthanonceayear.Thendingsofthe
inspection must be stored in writing until the time of the next
inspection.
When coming into contact with fuels, the rubber-bonded metal
bu󰀨ersofthemachinemaybecomedamagedorine󰀨ective.
Therefore,wipespilledfuelcarefullyo󰀨therubber-bonded
metalbu󰀨ers.
Fuelvaporsareeasilyammable.Donotsmokeandkeep
awayfromopenrewhilerefuelingthemachine.
The machine must not be fueled unless the engine is switched
o󰀨.

11
Safety instructions and
warnings
A variety of safety instructions and warnings are used
throughout this operating manual.
The following explains the meaning of signal words and
symbols.
ATTENTION warns of
the danger of material
damage.
CAUTION warns of the
danger of slight injury.
WARNING warns of a
danger that may lead to
death or serious injury.
DANGER warns of a
danger that will lead to
death or serious injury
unless avoided.
ATTENTION
CAUTION
WARNING
DANGER
The information symbol provides supplemental
information on the operation of the machine and
points to complementary technical information.

12
Sticker Meaning
1
All threaded unions must be
checkedforrmseatonaregular
basis and, particularly, after initial
use.
2The fuel tank may only be fueled
with regular gasoline.
3 Turn the cap to open and close it.
4
Use the designated lifting ring to
lift the machine.
Sound power level 109 dB (A),
Wear ear protection.
5*
When disconnecting the engine
bracket from the base plate,
make sure not to damage the
sensor cable.
The sensor must be detached
from the base plate.
6
Lever in position “0”: Choke is
open.
Lever in position “1”: Choke is
closed.
4.1. Information and safety stickers
*Only units equipped with COMPATROL compaction control.

13
5. Operation
Preparing the machine for
initial use
Remove all packaging material.
Check all components for visible damage. Do not start
the machine if detecting visible damage. Contact the
responsible dealer.
Check if the shipment of the machine and its components is
complete.
Checkthellleveloftheoperatinguidsandtopo󰀨if
necessary.
Set up the machine at its place of use.

14
1
2
3
4
5
6
7
8
910
11
Operating positions on the machine
Overall view CR 9-II Hd
1 Base plate with exciter
2 Mounting bracket
3 Gas lever
4 Handle
5 Guide bar
6 Lifting ring
7 Engine
8 Key switch
9 Start module
10* Compaction control system Compatrol
11 Choke lever
*Only units equipped with COMPATROL compaction control.
Figure 1

15
MS 15
5
1
2
4
3
The start module
1 Operational status indicator
(LED)
This indicator signals that the ignition of the machine is
switched on. It comes on as soon as the key switch (5) is set
to position “1”.
2 Oil pressure indicator (LED) Thisindicatorwarnsofinsu󰀩cientoilpressure.
Shut down the machine immediately when this indicator comes
on.
3 Operating hours counter Thiseldshowstheoperatinghourscompletedbythe
machine.
The counter will show the remaining time until the next
scheduledmaintenancefortherst10secondsafterthe
ignition was switched on (key switch (5) in position “1”).
4 Charge level indicator (LED) This indicator comes on if the charging current supply to the
starterbatteryisinsu󰀩cient.Whileoperationofthemachine
canresume,thecauseoftheinsu󰀩cientchargingcurrent
supplymustbeidentiedandrectied.
5 Key switch The key switch is used to switch the power supply (ignition) to
themachineonoro󰀨.Italsoactuatestheelectricstarterofthe
engine.
Switch in position “1”
The ignition is switched on.
Switch in position “0”
Theignitionisswitchedo󰀨.
Switch in position “2”
The electric starter is actuated.
ATTENTION
Danger of material damage from running electric starter.
The ignition key must spring back from position “2” to position
“1”. Otherwise:
Shut down the machine immediately.
Figure 2

16
1 3
2
The COMPATROL compaction control system
This indicator comes on as soon as the proper operating
frequency has been reached and signals that the compaction
control system is operational.
Iftheindicatorashesconstantly,themachineisoperating
with the wrong operating frequency.
The LEDs 1-7 indicate the achieved level of soil compaction.
The number of lit LEDs increases with the level of compaction.
If no additional LED comes on after another pass over the
same spot, the maximum level of compaction has been
reached.
3 Warning light (Red) The warning light warns of operation on soils that are too hard.
These types of soil cannot be compacted further with the
machine type used and may result in damage to the machine.
Figure 3
1 Operational status indicator
(Green)
2 Compaction indicator
(Yellow)

17
The attainable maximum may vary with the type and composition of the
soil. On sand, the maximum is commonly reached at a low number of lit
LEDs.
Following the compaction of a mix of gravel and crushed rock that is
uniformly graded and contains the proper concentration of water, the
indicator is likely to show six to seven lit LEDs.
It is important to closely monitor the indicator during the last pass. Places
where the number of lit LEDs drops sharply are poorly compacted. In
these places, the soil needs to be compacted again or may even have to
be replaced.
Possible indicator states
Function test of the LEDs A function test of the LEDs is performed when the ignition is
turned on, but the engine has not yet been started.
The operational status indicator (1) and the warning light (3)
light up permanently.
The LEDs of the compaction indicator (2) light up in
succession from left to right and go out in reverse order.
After engine start, before
reaching the operating
frequency
The warning light (3) signals by lighting up permanently that
the compaction indicator is not operational yet.
The LEDs of the compaction indicator (2) are not yet lit.
Theoperationalstatusindicator(1)signalsbyashingthatthe
operating frequency has not been reached yet.
Reaching the operating
frequency, operation
Upon reaching the operating frequency, the operational status
indicator (1) lights up permanently, indicating that the machine
is ready for operation.
The warning light (3) goes out.
The compaction indicator (2) starts lighting up, indicating the
achieved level of soil compaction.
Illumination of the warning
light
The warning light warns of operation on soils that are too hard.
If all LEDs of the compaction indicator (2) are lit together with
the warning light (3), the soil to be compacted is too hard.
Stop operation immediately to avoid damage to the machine.

18
1
2
3
4
Before starting work
Perform the following tasks before starting to work in order to
prevent failures or excessive wear.
Visual inspections Hydraulic line for leaks
Fuel system for leaks
Rubberbu󰀨ersforcrackformation
Other damage
Check and, if necessary,
correct the ll levels
Engine oil
Hydraulic oil
Fuel
Other inspections Checkallthreadedunionsforrmseat
Verify compliance with the maintenance schedule
Figure 4
1 Vandalismap
2 Valve box
3 Set screw guide bar
4 Charging socket

19
Working with the machine
Starting the engine
Adjust the desired work height of the guide bar with the set
screw(position3,gure4).
Openthevandalismap(position1,gure4).
Close the choke lever (slide down to position “I”).
Bring the gas lever into the full-throttle position “ON”.
Turn the ignition key to position “2” and hold it until the
engine turns over.
Release the ignition key as soon as the engine is running.
ATTENTION! Danger of material damage from running
electric starter.
The ignition key must spring back to position “1”
automatically. Otherwise, shut down the machine
immediately.
Set the gas lever to the idle speed “STOP”.
The operational status indicator signals that the machine
is ready for operation.
Allow the engine to warm up for a few minutes.
Open the choke lever (slide up to position “0).
ATTENTION
Risk of engine damage if start procedures take too long.
One start procedure must not be longer than 5 seconds. Pause
for at least 10 seconds before repeating the start procedure.
WARNING
Dangerofsu󰀨ocationfromengineexhaustswhenstartingthe
engine in closed rooms or poorly ventilated work areas.
Start the engine only in well-ventilated environments.
See section “Safety” for operating the machine in trenches.
ATTENTION
Risk of engine damage. The use of starter spray may lead to
overheating in the combustion chamber.
Do not use any starter spray.

20
ATTENTION
Danger of material damage or excessive wear if V-belt slips
through.
Operate the machine only in full-throttle mode, gas lever
position “ON”.
Start the engine.
Bring the gas lever into the full-throttle position “ON”.
Switch between forward and reverse travel by setting the
handle to the corresponding direction.
If the machine is equipped with the COMPATROL
compaction control system, the achieved compaction
of the soil can be read in the display.
The maximum possible compaction has been
reached when no additional LEDs come on after the
completion of another pass.
Switching o󰀨 the engine Bring the gas lever into the idle speed position “STOP”.
Turn the ignition key to position "0".
Pullouttheignitionkeyandclosethevandalismap.
CAUTION
Risk of injury if the machine is guided improperly.
Guide the machine safely with both hands on the handle.
CAUTION
There is a crushing hazard between the machine and the wall
during work in close proximity to walls.
Use extra caution when working close to obstacles
ATTENTION
Risk of damage to the bearings. Never work on soils that
cannot be compacted further. The optional COMPATROL
compaction control system warns of hard soils.
If all LEDs of the compaction indicator light up together with
the warning light, stop operation immediately.
Compacting
The forward and reverse travel of the machine is
innitelyvariable.
The speed of the machine is selected with the
correspondingdeectionofthehandle