weBoost Basic Home User manual

NEED HELP? support.weboost.com 866.294.1660
Installation Guide
Cell Signal Booster
Basic Home
A WILSON ELECTRONICS BRAND

Package Contents 1
Preparation 2
STEP 1-A & B: Connect Inside Antenna To Booster 3
STEP 2-A: Point Outside Antenna Toward Nearest Cell Tower 4
STEP 2-B: Mount Bracket To Outside Antenna 5
STEP 3: Route & Connect Cable To System 7
STEP 4: Power Up The Booster 8
Measuring Booster Performance 9
Light Patterns 11
Troubleshooting 12
Safety Guidelines 15
Specifications 16
Warranty 17
______
Index

1
BASIC HOME CELL PHONE SIGNAL BOOSTER
______
Package
Contents
Basic
Home
Inside
Antenna
Outside
Antenna
Cable
Connector
Window
Entry Cable
Roof/Pole
Mount
Bracket
Wall Mount
Bracket
Power
Supply
2-30’
Cables

2CELL PHONE SIGNAL BOOSTER BASIC HOME
______
Preparation
NOTE: These instructions will walk you through a “soft” install process to find
the optimal locations for the inside and outside antennas, then through the
process of the permanent installation.
You Will Need (tools not included)
Make sure the following materials are prepared and ready for your
installation.
o Ladder
o Phillips-head screwdriver
o 10mm open-end wrench or adjustable wrench
o Drill (if routing cable through wall)
o 1.25”-2” diameter pole existing pole (or order #901117)
o Recommended: Power Strip with surge protection
1 to 2 hours
2 people (a person to help with antenna calibration)

3
BASIC HOME CELL PHONE SIGNAL BOOSTER
NOTE: Do not connect booster to power until the system is fully installed.
______
Step 1-A & B: Connect Inside
Antenna To Booster
Connect Inside Antenna cable to the bottom port on Basic Home booster
labeled ‘INSIDE’ and place Inside Antenna in weak signal area at least 18
inches away from booster.
Inside
Antenna
Booster
finger tighten
only

4CELL PHONE SIGNAL BOOSTER BASIC HOME
______
Step 2-A: Point Outside
Antenna Toward Nearest
Cell Tower
Point the Outside Antenna toward the nearest cell phone tower. To find the
nearest tower, use an app such as ‘Open Signal’. This is the most critical step
of the installation process because it will determine the overall performance
of the booster system.
Cell Tower
Outside Antenna
NOTE: The Outside Antenna must be at least
50 feet horizontal or 20 feet vertical from the Inside
Antenna for best performance. Make sure the Inside
Antenna and Outside Antennas are setup so they are
facing away from each other.
f
a
c
i
n
g
a
w
a
y

5
BASIC HOME CELL PHONE SIGNAL BOOSTER
______
Step 2-B: Mount Bracket To
Outside Antenna
Pole Mounting and Wall Mounting Options are included. The pole mounting
option is preferred because it would be easier to adjust to the direction
of the cell tower.
Attach the L-Bracket to the Outside Antenna and use the U-Bolts/Pole Bracket
to attach the L-Bracket to a pole.
NOTE: Mounting on existing roof exhaust pipe would
be a good time-saver option.
Cell Tower
Outside Antenna
Pole
(1.25”-2.0”dia.)
U-bolt &
Pole Bracket
L-Bracket
Pole Mounting Option

6CELL PHONE SIGNAL BOOSTER BASIC HOME
______
(STEP 2-B cont.)
Drill holes using
3/16 inch bit
Tap anchors in
Fasten bracket to back
of Outside Antenna Secure bracket to wall
mounting
Outside Antenna
on wall bracket
sideview
Wall Mounting Option

7
BASIC HOME CELL PHONE SIGNAL BOOSTER
______
Step 3: Route & Connect
Cable To System
Connect the white RG-6 Cable to Outside Antenna and route cable
into the home. All connections should be finger tightened only.
A Window Entry Cable is provided to help make cable entry easier.
Route cable to the Basic Home booster and connect to top port
labeled ‘OUTSIDE’.
Outside
Antenna
Inside
Antenna
Outside
Antenna
Cell
Tower
Inside
Antenna
RG-6 Cable RG-6 Cable
Window
Entry Cable
Booster
Window Entry Cable
Booster

8CELL PHONE SIGNAL BOOSTER BASIC HOME
______
Step 4: Power Up The
Booster
5
0
F
E
E
T
H
O
R
I
Z
O
N
T
A
L
O
R
2
0
F
E
E
T
V
E
R
T
I
C
A
L
D
I
S
T
A
N
C
E
5
0
F
E
E
T
H
O
R
I
Z
O
N
T
A
L
O
R
2
0
F
E
E
T
V
E
R
T
I
C
A
L
D
I
S
T
A
N
C
E
Plug the Power Supply into wall outlet then connect to Basic Home
booster and enjoy your boosted cell signal!
Outside
Antenna
Outside
Antenna
Cell
Tower
Inside
Antenna
RG-6 Cable RG-6 Cable
Window
Entry Cable
Booster
to power
Inside
Antenna
Power Supply
Window Entry Cable
Booster

9
BASIC HOME CELL PHONE SIGNAL BOOSTER
______
Measuring Booster
Performance
Settings > About Phone > Status or Network > Signal Strength
or Network Type and Strength (exact options/wording
depends on phone model).
Android™
iPhone is a registered trademark of Apple Inc. Android is a trademark of Google Inc.
iOS 11 and later no longer displays the decibel (dBm) reading
in ‘Field Test Mode’. Tip: Using the dot signal strength indicator
on your cell phone and/or data speed tests can assist you in
finding the strongest signal direction as well as placing calls
in dierent locations. For changes/updates on this issue,
periodically go to weboost.com/signalstrength.
iPhone®
How To Get Signal Strength As A Number
All Other Phones & Alternate Methods
Go to www.weboost.com/test-mode-instructions/

10 CELL PHONE SIGNAL BOOSTER BASIC HOME
EXCELLENT GOOD FAIR POOR DEAD ZONE
3G/1x
4G/LTE
-70dBm
-90dBm
-71 to -85dBm
-91 to -105dBm
-86 to -100dBm
-106 to -110dBm
-101 to -109dBm
-111 to -119dBm
-110dBm
-120dBm
SIGNAL
STRENGTH
EXCELLENT GOOD FAIR POOR DEAD ZONE
3G/1x
4G/LTE
-70dBm
-90dBm
-71 to -85dBm
-91 to -105dBm
-86 to -100dBm
-106 to -110dBm
-101 to -109dBm
-111 to -119dBm
-110dBm
-120dBm
SIGNAL
STRENGTH
Having an accurate measurement of signal strength in decibels (dBm) is crucial when
installing your system. Decibels accurately measure the signal strength you are receiving.
DID YOU KNOW a signal increase of just 3dB is 2
times the power and signal amplification!
Compare Results
______
(MEASURING BOOSTER PERFORMANCE cont.)
Signal Strength without Booster
Note here:
Signal Strength with Booster
Note here:

11
BASIC HOME CELL PHONE SIGNAL BOOSTER
______
Light Patterns
Solid Green
This indicates that your booster is
functioning properly and there are no
issues with installation.
Blinking Green, Then Red
Band has reduced gain. This indicates that one or more of the booster bands has reduced
power due to a feedback loop condition called oscillation. This is a built in safety feature
to prevent harmful interference with a nearby cell tower. If you are already experiencing
the desired signal boost, then no further adjustments are necessary. If you are not
experiencing the desired boost in coverage then refer to the Troubleshooting section.
Solid Red
Band has shutoff. This is due to a feedback loop condition called oscillation.
This is a built in safety feature that causes a band to shut off to prevent harmful
interference with a nearby cell tower. Refer to Troubleshooting section.
Blinking Green, Orange
Band has reduced gain. This indicates that one or more of the booster bands has reduced
power due to overload from nearby cell tower. This is a built in safety feature to
prevent harmful interference with a nearby cell tower. If you are already experiencing
the desired signal boost, then no further adjustments are necessary. If you are not
experiencing the desired boost in coverage then refer to the Troubleshooting section.
Solid Orange
Band has shutoff due to overload from nearby cell tower. Outside Antenna must be
adjusted. Refer to Troubleshooting section.
Light O
If the Signal Booster’s light is off, verify your power supply has power.

12 CELL PHONE SIGNAL BOOSTER BASIC HOME
______
Troubleshooting
FIXING ANY RED LIGHT ISSUES
FIXING ANY ORANGE LIGHT ISSUES
1
2
3
Verify Outside Antenna faces away from the Inside Antenna. Un-plug and re-
plug in power supply.
Verify the Inside Antenna is at least 18” from the Booster and pointed away
from the Booster. Unplug and re-plug in power supply.
Tighten all cable connections (be sure to finger tighten only, do NOT use tools).
You may want to undo and redo the connection completely. Unplug and re-
plug in power supply.
Increase the distance (horizontally or vertically) between the Outside and
Inside antenna. Add included cable if needed. Un-plug and re-plug in
power supply.
Outside Antenna must be adjusted. Wait 10 seconds between adjustments for
the lights to reset.
4
This involves Solid Red & Blinking Green/Red lights.
This involves Solid Orange & Blinking Green/Orange lights.
IF YOU ARE HAPPY WITH THE COVERAGE, THESE LIGHT ISSUES DON’T HAVE TO
BE RESOLVED. YOUR CARRIER’S BAND HAS NOT BEEN AFFECTED.
Pole Mount Option: Rotate the Outside Antenna away from the strongest
cellular signal in small increments (45°) until the light turns green. Unplug
and re-plug power supply.
Wall Mount Option: Change mount location. Move the Outside Antenna
to a wall outside the building to see if the lights turn green. Un-plug and
re-plug power supply.
NEED HELP? support.weboost.com 866.294.1660

13
BASIC HOME CELL PHONE SIGNAL BOOSTER
866.294.1660
______
Antenna Kit Options
Ω
50
50
75
50
75
75
50
50
75
75
75
Antenna Type
Desktop Antenna 700-2100 MHz
Wall Mount Panel Antenna
Wall Mount Panel Antenna
Wall Mount Panel Antenna
Wall Mount Panel Antenna
Wall Mount Panel Antenna
4G Dome Antenna
4G Dome Antenna
4G Dome Antenna
4G Dome Antenna
4G Dome Antenna
Coax Type
RG-174
Wilson-400
Wilson-400
RG-58
RG-6
RG-11
Wilson-400
RG-58
RG-11
RG-174
RG-6
Kit #
301211
311135
311155
311135
311155
311155
304412
304412
304419
304419
304419
Ln(ft)
5
60
60
20
30
50
10
10
10
10
10
FIXED INSIDE ANTENNA KIT OPTIONS

14 CELL PHONE SIGNAL BOOSTER BASIC HOME
Ω
50
50
75
50
50
50
50
50
50
75
75
50
50
75
75
75
75
50
50
50
Antenna Type
Wide Band Directional
Wide Band Directional
Wide Band Directional
Yagi 700/800/900 MHz
Yagi 700/800/900 MHz
Mini-Mag Antenna
Yagi 700/800/900 MHz
Pole Mount Panel Antenna
Pole Mount Panel Antenna
Pole Mount Panel Antenna
Wide Band Directional
Yagi 700/800/900 MHz
Pole Mount Panel Antenna
4G Omni Antenna
4G Omni Antenna
4G Omni Antenna
4G Omni Antenna
4G Omni Plus Antenna
4G Omni Plus Antenna
4G Omni Plus Antenna
Coax Type
Wilson-400
RG-58
RG-6
RG-6
RG-58
LMR-100
RG-11
RG-58
Wilson-400
RG-6
RG-11
Wilson-400
RG-11
RG-11
RG-174
RG-6
RG-58
Wilson-400
RG-58
RG-11
Kit #
314400
314411
314475
301111
301111
301126
301111
314453
314453
314473
314475
301111
314473
304421
304421
304421
304421
304422
304422
304422
Ln(ft)
75
25
30
75
50
10
40
25
75
40
75
170
75
20
10
10
10
20
10
20
FIXED OUTSIDE ANTENNA KIT OPTIONS
______
(ANTENNA KIT OPTIONS cont.)

15
BASIC HOME CELL PHONE SIGNAL BOOSTER
______
Safety Guidelines
To uphold compliance with network protection standards, all active cellular devices
must maintain at least six feet of separation distance from Inside Panel and Dome
antennas and at least four feet of separation distance from desktop Antenna.
Use only the power supply provided in this package. Use of a non-weBoost product
may damage your equipment.
The Signal Booster unit is designed for use in an indoor, temperature-controlled
environment (less than 100 degrees Fahrenheit). It is not intended for use in attics or
similar locations subject to temperatures in excess of that range.
RF Safety Warning: Any antenna used with this device must be located at least 8
inches from all persons.
AWS Warning: The Outside Antenna must be installed no higher than 10 meters (31’9”)
above ground.
FOR MORE INFORMATION ON REGISTERING YOUR SIGNAL BOOSTER WITH YOUR
WIRELESS PROVIDER, PLEASE SEE BELOW:
AT&T: https://securec45.securewebsession.com/attsignalbooster.com/
Verizon Wireless: http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your
provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers
may not consent to the use of this device on their network. If you are unsure, contact your provider.
You MUST operate this device with approved antennas and cables as specified by the
manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person.
You MUST cease operating this device immediately if requested by the FCC or licensed wireless
service provider.
WARNING. E911 location information may not be provided or may be inaccurate for calls served by
using this device.
This device may be operatedONLYin a fixed location for in-building use.

16 CELL PHONE SIGNAL BOOSTER BASIC HOME
______
Specifications
Basic Home
Product Number U471001
Model Number 460020
FCC ID: PWO460020
Connectors SMA-Female on the Inside Antenna / F-Female on the Outside Antenna
Antenna Impedance 50 Ohms / 75 Ohms
Frequency 698-716 MHz, 746-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz
Power output for single cell phone
(Uplink) dBm
700 MHz
Band 12/17
700 MHz
Band 13
1700 MHz
Band 4
23.94 24.19 24.55
Power output for single cell phone
(Downlink) dBm
700 MHz
Band 12/17
700 MHz
Band 13
2100 MHz
Band 4
11.64 11.92 11.9
Noise Figure 5 dB nominal
Isolation > 110 dB
Power Requirements AC / DC 5V, 4A, w/2.5x5.5mm Jack
Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot
be adjusted without factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not
alter incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the
Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected. If a detected signal is
too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically
turn the power o on that band. For a detected oscillation the Signal Booster will automatically resume normal
operation after a minimum of 1 minute. After 5 (five) such automatic restarts, any problematic bands are
permanently shut o until the Signal Booster has been manually restarted by momentarily removing power from
the Signal Booster. Noise power, gain, and linearity are maintained by the Signal Booster’s microprocessor.
The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when
multiple carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output
signal is re-radiated and can cause interference to adjacent band users. This power reduction is to be by
means of input power or gain reduction and not by an attenuator at the output of the device.
This device complies with Part 15 of FCC rules. Operation is subject to two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation. Changes or modifications not expressly approved by weBoost could void
the authority to operate this equipment.

17
BASIC HOME CELL PHONE SIGNAL BOOSTER
2 YEAR WARRANTY
weBoost Signal Boosters are warranted for two (2) years against defects in
workmanship and/or materials. Warranty cases may be resolved by returning the
product directly to the reseller with a dated proof of purchase.
Signal Boosters may also be returned directly to the manufacturer at the
consumer’s expense, with a dated proof of purchase and a Returned Material
Authorization (RMA) number supplied by weoost. weBoost shall, at its option,
either repair or replace the product.
This warranty does not apply to any Signal Boosters determined by weBoost
to have been subjected to misuse, abuse, neglect, or mishandling that alters or
damages physical or electronic properties.
Replacement products may include refurbished weBoost products that have been
recertified to conform with product specifications.
RMA numbers may be obtained by contacting Customer Support
DISCLAIMER: The information provided by weBoost is believed to be complete
and accurate. However, no responsibility is assumed by weBoost for any business
or personal losses arising from its use, or for any infringements of patents or other
rights of third parties that may result from its use.
NEED HELP? support.weboost.com 866.294.1660

3301 East Deseret Drive, St. George, UT
866.294.1660 www.weboost.com support.weboost.com
Copyright © 2019 weBoost. All rights reserved.
weBoost products covered by U.S. patent(s) and pending application(s)
For patents go to: weboost.com/us/patents
NOT AFFILIATED WITH WILSON ANTENNA GDE000186_Rev04_05.12.20