weBoost Drive 4G-M User manual

•
. :: weboost®
Drive 4G-M™
Quick Install Guide
For more information refer to full Install Guide at:
www.weboost.com/us/installguide/drive4G-M

Package Contents
Drive 4G-M Signal Booster
Mini-Mag Mount Antenna Slim Low Profile Antenna
DC Power Supply
Quick Install Diagram
Connect Cables to Drive 4G-M I Power Supply Cord
Connect Power Supply

1 Outside Antenna Installation
Select a location
on
top of the vehicle
to
mountthe Mini-Mag
Mount Antenna that
is:
• Near the center ofthe vehicle's
roof.
• At least 12 inches from any
other antennas.
Mini-Mag MountAntenna
• Free of obstructions.
• At least 6 inches from any
windows (including sunroofs).

2 Running Antenna Cable
Run the Outside Antenna cable into the car. The cable is strong
enough that it may be shut in most vehicle doors without damaging
the cable. For a cleaner look, carefully pull
down
the
door
seal, run
the cable underthe seal, and push the seal back into place. This
method reduces wear on the cable as the
door
opens and closes.
i
l
1
I
I'
if
l /
//
\ ,f
\
·'

3 Inside Antenna Installation
Identify a place on the side of the seat
to
mount the Slim Low
Profile Antenna. The location should be at least 18 inches but
no
more than 36 inches from where the cellular device will be used.
Peel
off the backing of the Velcro® and attach
to
seat.

4 Connect Coax Cables
to
Drive 4G-M
Select a location for the Drive 4G-M that is free from excessive
heat, direct sunlight and moisture and that has properventilation.
Good locations include underneath a seat or underthe dashboard.
Connect the cable from the Mini-Mag Mount Antenna
to
the port
labeled "Outside Antenna" on the Drive 4G-M and connect the
cable from the Slim Low Profile Antenna
to
the port labeled "Inside
Antenna" on the booster.
Slim
Low
ProfileAntenna Mini-Mag MountAntenna

5 Connect Power
Supply
to
Drive 4G-M
Connectthe power supply cord
to
the end
of
the Drive 4G-M
labeled "Power." NOTE: Do NOT connect the power
to
the Signal
Booster until you have connected both the Inside and Outside
Antennas.
0
0
0
0
Power
Supply

6 Connect
to Power Supply
Plug the power adapter into vehicle's 12V DC power supply. Power
up your Drive 4G-M by flipping the switch on the back of the DC
power adapter on. If your Drive 4G-M is working correctly, the
lights will be green.
NOTE: Iflights are not green on your weBoost booster, please refer
to the full install guide online
or contact customer support at
1-866-294-1660
or email at [email protected].

How It Works
Your cell phone
is an essential part of your life. weBoost is here to
ensure you have seamless connections on all your cellular devices.
The Drive 4G-M cellular signal booster
is a effective solution to all
those times you have lost a call while driving your vehicle due to a
weak cell signal. Installation
is simple and can be completed with
minimal tools.
\ Outside Antenna
\
\~·~';:)
\
-- \
' \
i Power Supply
)
S1gnal Received and
Transmitted

Note:
THE
ALUMINUM
CASING
OF
YOUR
SIGNAL
BOOSTER
WILL
ADJUST
TO
THE
TEMPERATURE
OF
ITS
ENVIRONMENT,
BUT
IS
DESIGNED
TO
PROTECT
THE
SIGNAL
BOOSTER
TECHNOLOGY
FOR
EXAMPLE,
IN
THE
SUMMER,
THE
SIGNAL
BOOSTER
CASE
MAY
BE
AS
HOT
AS
150
DEGREES
INSIDE
YOUR
VEHICLE
.
THESE
HIGH
TEMPERATURES
WILL
NOT
DAMAGE
THE
SIGNAL
BOOSTER
,
NOR
DO
THEY
POSE
A
FIRE
RISK
TO
THE
VEH
I
CLE.
AGAIN,
BE
SURE
TO
PLACE
YOUR
SIGNAL
BOOSTER
IN
A
LOCATION
WITH
ADEQUATE
VENTILATION
AND
AWAY
FROM
DIRECT
SUNLIGHT
OR
MOISTURE
.
THE
DRIVE
4G-M
SIGNAL
BOOSTER
MAY
REMAIN
ON,
IN
VEHICLES
WHOSE
12V
DC
POWER
SOURCES
DO
NOT
AUTOMATICALLY
SHUTDOWN
WHEN
THE
VEHICLE
IS
TURNED
OFF.
THIS
COULD
RESULT
IN
DISCHARGING
THE
VEHICLES
BATTERY
IN
ONE
TO
TWO
DAYS
.