weBoost 470113 User manual

®
TM
Cellular Signal Booster
460101
Need help? www.WilsonElectronics.com Tech Support 866-294-1660
Mon.- Fri. Hours: 7 am to 6 pm MST
ENGLISH FRANÇAIS
Drive 3G-FLEX
Quick Install Guide
Package Contents
Quick Install Diagram
Outside Antenna Installation
Running Antenna Cable
Connect Cable to Drive 3G-FLEX / Power Supply Cord
Connect Power Supply
Mount Dash Bracket
NEED ASSISTANCE? WE CAN HELP!
Contact our U.S.-BASED CUSTOMER SUPPORT:
n Contact our U.S.- based customer support team at
1-800-501-3153 or email at [email protected]
n Go online for how to resolve the most common issues at
n Find a weBoost Installer on our web site at
Installation is simple, but we’re here to make it even easier.
Your cell phone is an essential part of your life. weBoost is here to
ensure you have seamless connections on all your cellular devices.
The Drive 3G-FLEX cellular signal booster is a effective solution to
all those times you have lost a call while driving your vehicle due to
a weak cell signal. Installation is simple and can be completed with
minimal tools.
Note: How It Works
Signal Received and
Transmitted
Power Supply
Outside Antenna
For more information refer to full Install Guide at:
Product Registration
Thank you for purchasing this weBoost product. Please take time to
register your new product at our website:
Registering is quick and easy, it only takes 2-3 minutes to complete.
Your information is secure, we don’t share or sell your information
to other third parties.
TM
Cellular Signal Booster
460101
Need help? www.WilsonElectronics.com Tech Support 866-294-1660
Mon.- Fri. Hours: 7 am to 6 pm MST
ENGLISH FRANÇAIS
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
RF Safety: Any antenna used with this device must be located at least 8 inches from all persons.
FCC ID: PWO460013 IC: 4726A-460013
THE SIGNAL BOOSTER UNIT IS DESIGNED FOR USE IN AN INDOOR, TEMPERATURE-CONTROLLED
ENVIRONMENT (LESS THAN 150 DEGREES FAHRENHEIT). IT IS NOT INTENDED FOR USE IN ATTICS
OR SIMILAR LOCATIONS SUBJECT TO TEMPERATURES IN EXCESS OF 150°F.
IT IS VERY IMPORTANT TO POWER YOUR SIGNAL BOOSTER USING A SURGE PROTECTED AC
POWER STRIP WITH AT LEAST A 1000 JOULE RATING. FAILURE TO DO THIS WILL VOID YOUR
WARRANTY IN THE EVENT OF A POWER SURGE OR LIGHTNING STRIKE.
Drive 3G-FLEX
Drive 3G-FLEX
Mini-Magnet Antenna
AC/DC Power Supply
USB Cable w/Power Adapter
Antenna Window Mount
Dash Mounting Kit
111568_Rev02_01.30.15
https://cellphonesignalbooster.us/
https://cellphonesignalbooster.us/
https://cellphonesignalbooster.us/
https://cellphonesignalbooster.us/

Outside Antenna Installation Running Antenna Cable Connect Coax Cables to Drive 3G-FLEX
Connect Power Supply to Drive 3G-FLEX Connect to Power Supply Mount Dash Bracket (optional).
Select a location on top of the vehicle to mount the Mini-Mag
Mount Antenna that is:
Run the Outside Antenna cable into the car. The cable is strong
enough that it may be shut in most vehicle doors without damaging
the cable. For a cleaner look, carefully pull down the door seal, run
the cable under the seal, and push the seal back into place. This
method reduces wear on the cable as the door opens and closes.
Connect the cable from the Mini-Mag Mount Antenna to the port
labeled “Antenna” on the Drive 3G-FLEX.
Plug the power adapter into vehicle’s 12V DC power supply. If your
Drive 3G-FLEX is working correctly, the lights will be green.
NOTE: If lights are not green, please refer to the full install guide
online or contact customer support at 1-800-501-3153 or email at
[e-mail]
1 2 3
4 5 6
DC Power Adapter
Vehicle’s Power Supply Dash Mount Bracket
Drive 3G-FLEX
Drive 3G-FLEX
nNear the center of the vehicle’s
roof.
nAt least 12 inches from any
other antennas.
nFree of obstructions.
nAt least 6 inches from any
windows (including sunroofs).
Connect the power cable to the mini-USB port on the bottom of the
Drive 3G-FLEX.
Mini-Mag Mount Antenna
Clean the area where the bracket is to be mounted with the alcohol
wipe included. Allow the area to dry. Peel the backing to expose
the adhesive and press the bracket onto the desired location on
the dashboard.