weBoost DRIVE SLEEK User manual

User Manual
Vehicle Signal Booster Kit
DRIVE SLEEK
A WILSON ELECTRONICS BRAND
NEED HELP? support.weboost.com 866.294.1660

______
Index
Package Contents 1
STEP 1: Mount Outside Antenna 2
STEP 2: Route & Connect Booster 3
STEP 3: Route Cable To Front Of Vehicle 5
STEP 4: Connect System To Power 6
STEP 5: Insert Phone Into Cradle 7
Light Patterns 8
Troubleshooting 9
Safety Guidelines 11
Specifications 12
Warranty 14

DRIVE SLEEK CELL PHONE SIGNAL BOOSTER 1
________
Package
Contents
Sleek
Cradle
Outside
Antenna
Signal
Booster
Power
Supply
Magnetic
Vent Mount
(for cradle)

2CELL PHONE SIGNAL BOOSTER DRIVE SLEEK
______
Step 1: Mount Outside
Magnetic Antenna
NOTE: For roofs that are not metallic, use the included metal disk by peeling
away the adhesive cover and sticking on the clean surface.
6 in. away from windows
(including sunroofs)
WORKS WITH ALL VEHICLES
Identify a location on the top of your vehicle that is:
 Near the center of the roof
 At least 12 inches away from any other antennas
 At least 6 inches away from any windows
(including sunroofs)
Clean the surface where you will place the outside
antenna.
Mount the outside antenna.

DRIVE SLEEK CELL PHONE SIGNAL BOOSTER 3
______
Step 2: Route & Connect
Booster
Route the cable into the vehicle. See examples below.
NOTE: The cable is strong enough that it may be shut in most vehicle doors
without damaging the cable.
Car/Sedan: Cable routed
into rear side door.
SUV/Van/Hatchback: Cable
routed into top of hatchback door.
Truck: Cable routed into
side door.
Identify a location on the top of your vehicle that is:
 Near the center of the roof
 At least 12 inches away from any other antennas
 At least 6 inches away from any windows
(including sunroofs)
Clean the surface where you will place the outside
antenna.
Mount the outside antenna.

4CELL PHONE SIGNAL BOOSTER DRIVE SLEEK
______
(STEP 2 cont.)
Connect the cable from the outside antenna to the booster
port labeled
ANTENNA
by simply pressing the connector in
until you hear a “click”.
ANTENNA
cable from
outside antenna
booster

DRIVE SLEEK CELL PHONE SIGNAL BOOSTER 5
______
Step 3: Route Cable To Front
Of Vehicle
We recommend routing the 15ft. fixed cable from the
booster, under mats and between seats up to the front of
the vehicle where the cradle will be located.
Connect booster cable to cable from cradle.
to front of
vehicle
snap-in
connectors
cradle

6CELL PHONE SIGNAL BOOSTER DRIVE SLEEK
______
Step 4: Connect System To
Power
Connect the power to the 12V CLA port on your vehicle and
route power cable back to the booster.
Connect power cable to booster port labeled .
NOTE: We recommend routing with the same path as the cable going up to
the cradle (under mats and between seats).
NOTE: The booster will be on whenever there is power from the 12V CLA
port. If your vehicle always has power going to this port, you may want to
unplug this when you’re not driving so the booster does not drain your
battery.
ANTENNA
connect power supply
to 12V port
connect
to booster

DRIVE SLEEK CELL PHONE SIGNAL BOOSTER 7
______
Step 5: Insert Your Phone
Into Cradle
Make sure you have plenty of slack in the cable going up
to the cradle (velcro straps included to manage excess
cable). Insert your phone into cradle and watch your signal
increase!
NOTE: Magnetic vent mount included to mount the cradle to your dash.
connect
to booster
cradle extends
insert phone into
cradle to boost signal
magnetic vent mount

8CELL PHONE SIGNAL BOOSTER DRIVE SLEEK
______
Light Patterns
Solid White
This indicates that your booster is functioning properly and at maximum gain.
Light O
Needs power.
NEED HELP? support.weboost.com 866.294.1660