Well Traveled Living Deluxe Patio Heater User manual

Patio Heater
Owner’s Manual
Warning: For OUTDOOR USE only
Deluxe & Standard Models
Residential Applications Only
*** Important Notice ***
[phone]
Do NOT return to place of purchase!
Please contact our Toll Free Hotline for
customer service & warranty issues
Well Traveled Living
716 South 8th Street, Amelia Island, FL 32034 USA

2
TOOLS AND PARTS NEEDED FOR ASSEMBLY
FOR YOUR SAFETY
WARNING
WARNING: For Outdoor Use Only
TOOLS REQUIRED: (not included)
7/16 Wrench
3/8 Open End Wrench
Adjustable Opening Wrench, 8 Long
Philips Head Screwdriver
Leak Detection Solution ( Instructions how to make solution are included in Step 8 )
Estimated time for assembly: 30-45 minutes.
"
"
"
Note: 20 Pound, 5 Gallon LPG Tank is not
supplied
Well Traveled
For questions, replacement parts, service help, or other assistance, please
call Well Traveled Service Hotline at: 1-800-766-9633.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance. The Product is to be used
only in well ventilated areas and not to be used
in a building, tent, cabin, boat, garage or any
other enclosed area.
If stored indoors, detach and leave cylinder
outdoors
your gas supplier
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to appliance.
2. Extinguish any open flame.
3. If odor continues, immediately call
Improper installation, adjustment, alteration,
services or maintenance can cause injury, death
or property damage. Read the installation,
operating and maintenance instructions
thoroughly before installing or servicing this
equipment.

3
PARTS
Well Traveled
15
17 1 Regulator
1 Cylinder (Not Supplied)
1
2
3
4
5
6
7
8
9
10
11
4 Reflector Cap
1 Head Assembly
1 Gas Hose
1 Post
1 Cylinder Cover
1 Cylinder Base
15 M6 Nuts
18 6mm Washers
5 M4 8 Bolts
x
3 Post Mounts
10
12
1 Center Reflector Cap
12 M6 10 Bolts
x
13
15
16
3 M6 x70 double pointed bolts
14
5 4mm Washers
12
13
9
17
16
6 M5 8 Bolts
x
18
6 5mm Washers
11
14
2
4
5
7
6
3
1
8
14
16
17
10
9
15
13

4
PRECAUTIONS
Well Traveled
Do not use the heater in an explosive atmosphere.
Keep the heater away from areas where gasoline or other
flammable liquids or vapors are stored.
Prior to use, check for damaged parts such as hoses,
regulators, pilot or burner.
Always assure there is ample fresh air ventilation.
For outdoor use ONLY.
Never replace or substitute the regulator with any regulator
other than the factory suggested replacement.
Do not clean with cleaners that are combustible
or corrosive.
the heater
Do not paint radiant screen, control panel or top canopy
reflector.
All leak tests should be done with a soapy solution. NEVER
USE AN OPEN FLAME TO CHECK FOR LEAKS.
The LP gas cylinder should be turned off when the
heater is not in use.
At least once a year the unit should be inspected, for the
presence of spiders, spider webs or other insects. Check the
heater immediately if any of the following exist:
1. The smell of gas in conjunction with extreme yellow
colored tips of the burner flames.
2. The heater does not reach temperature.
3. The burner makes popping noise during use (a slight
popping noise is normal when the burner is extinguished
after using).
The propane hose with regulator assembly shall be located
out of pathways where people may trip over it or in areas
where the hose will not be subject to accidental damage.
Children and adults should be aware of the hazards of high
surface temperature and shall stay away to avoid clothing
burn or ignition.
Young children should be carefully supervised when they
are in the area of the heater.
Clothing or other flammable material should not be hung
from the heater, or placed on or near the heater.
Installation and repair should be done by a qualified
service person. The heater should be inspected before
use and cleaning may be required at least once a year, or as
necessary. It is imperative that control compartment, burner
and circulating air passageways of the heater be kept
clean.
Keep the appliance area clear of combustible materials
such as gasoline and other flammable vapors and liquids.
Do not obstruct the flow of combustion and ventilation air.
Keep the ventilation opening of the cylinder enclosure free
and clear of debris.
NOTE: PLEASE READ THE FOLLOWING SAFETY RULES
The appliance shall not be used in basements or below
ground level.
It must always be placed on a solid and level surface.
Read the instructions before use.
This appliance must be installed in
accordance with such regulations as
are in force.
This appliance must only be used outdoors.
Using this product in an enclosed area may cause
injury, death or property damage.
WARNING
Disconnect LPG bottle before moving the heater.
Any guard or other protective device removed for
servicing the heater must be replaced prior to
operating the heater.
Do not attempt to alter unit in any manner.
EXAMPLE: using the heater without the top canopy
reflector or radiant screen.
Do not shorten the burner post assembly.
Save these instructions! Retain in a safe place for future reference.
PRECAUTIONS

5
ASSEMBLY
Well Traveled
Step 1 ----
Step 1
Step 2 ---- Step 2
M5 X 8 bolts (6 pcs) and 5mm washers (6 pcs)
Attach the post to the post mounts using
Attach Post to Base Assembly
7
Attach Cylinder Cover to Post Mounts
Attach the cylinder cover to the post mounts.
7
6
14
11
5
CAUTION:
Read ALL assembly instructions thoroughly
and carefully to insure proper, safe assembly

6
ASSEMBLY
Well Traveled
Step 3
Step 4
Step 3 ---- Attach Head Assembly to Post
3
5
3
13
16
10
12
4
Load head assembly by inserting gas hose
into post.
Insert head assembly into post.
Tighten securely using M4X8Bolts (5 pcs)
and 4mm washers (5 pcs).
Step4 ---- Attach Double Pointed Bolt to
Attach M6 X 70 double pointed bolts (3 pcs) and
6mm washers (3 pcs) to the top of head assembly
and tighten the bolts securely.
Head Assembly
CAUTION:
Read ALL assembly instructions thoroughly
and carefully to insure proper, safe assembly

Step 5 ---- Attach Center Reflector to Reflector
Attach center reflector to the top of reflector (4 pcs)
by M6 X 10 mm screws (12 pcs) ,
Step 5
2
1
15
Step 6
3
6mm washers (12 pcs) and nuts (12 pcs).
Step 6 ---- Attach Center Reflector and Reflector
Load center reflector and reflector to the top
of head assembly by
M6 X 70 double pointed bolts (3 pcs)
to the top of Head Assembly
6mm washers (3 pcs) and nuts (3 pcs)
10
9
10
9
7
Well Traveled
ASSEMBLY
CAUTION:
Read ALL assembly instructions thoroughly
and carefully to insure proper, safe assembly

8
ASSEMBLY
Well Traveled
Step 7
Step 8
Step 7 ---- Connect Gas Line to Cylinder
Step 8 ---- Check for leak
Attach gas hose to regulator.
Attach regulator to cylinder.
Move cylinder to the plate of base assembly.
Your Patio Heater has been checked at all
factory connections for leaks, To check the
Connection of the gas hose/regulator/cylinder.
1) Make leak solution by mixing 1part liquid
dish soap and 3 parts water.
2) Spoon several drops (or use squirt bottle)
of the solution onto the gas hose/regulator
and regulator/cylinder connection.
3) Inspect the connections and look for bubbles.
4) If no bubbles appear, the connection is safe.
5) If bubble appear, there is leak, loosen and
re-tighten this connection.
CAUTION:
Read ALL assembly instructions thoroughly
and carefully to insure proper, safe assembly

9
ASSEMBLY
Well Traveled
Step 9---- Lower Cylinder Cover onto
Cylinder Base
Lower the cylinder cover onto the cylinder base .
Step 9
6
8
CAUTION:
Read ALL assembly instructions thoroughly
and carefully to insure proper, safe assembly

OPERATION
Well Traveled
WARNING:
Do NOT attempt to operate heater until you have
read and understand all precautions.
Failure to do so can result in serious personal injury, death
or property damage.
Before Turning Gas Supply ON
Your heater was designed and approved for OUTDOOR USE ONLY. Do NOT
use it inside a building ,or any other enclosed area.
Make sure surrounding areas are free of combustible materials, gasoline
and other flammable vapors or liquids.
Ensure that there is no obstruction to air ventilation.
Be sure all gas connections are tight and there are no leaks.
Be sure the access panel is clear of debris.
Be sure any component removed during assembly or servicing is replaced
and fastened prior to starting.
Before Lighting
Heater should be thoroughly inspected before each use, and by a qualified
service person at least annually.
If relighting a hot heater, always wait at least 5 minutes.
Our heater is tested for quality assurance.
Ignition attempts should succeed 8 out of 10 attempts.
LIGHTING INSTRUCTIONS
If you experience any ignition problem, turn off the heater and gas
supply, and consult "Troubleshooting" on page 14.
FOR YOUR SAFETY:
If at any time you are unable to light burner
and smell gas, wait 5 minutes to allow gas
to dissipate before attempting to light heater.
If, after 1 minute, you are unable to light
burner, wait 5 minutes and allow flammable
vapors to dissipate before attempting to
light heater again.
WARNING
FOR YOUR SAFETY:
Do NOT touch or move heater for at least 45
minutes after use.
Allow emitter and dome to cool before
touching.
WARNING
P
u
s
h
t
o
t
u
r
n
O
F
F
H
I
G
H
L
O
W
I
G
N
I
T
E
P
I
L
O
T
P
u
s
h
t
o
t
u
r
n
O
F
F
H
I
G
H
L
O
W
I
G
N
I
T
E
P
I
L
O
T
1)Turn the control knob to "OFF" position.
2)Fully open gas valve
3) Push in gas control knob and turn counter clockwise to "IGNITE"
then to "PILOT" position, this will light the pilot.
If needed, keep depressing and turning control knob counter clockwise
until the pilot lights.(You will hear 2 clicking noises)
4) Once the pilot is lit, continue to keep the control knob depressed for at least
30 seconds, After 30 seconds release control knob.
5) If pilot does not stay lit, repeat steps 3 and 4.
6) If pilot still does not stay lit, then:
a) Push in gas control knob and turn counter clockwise to "IGNITE"
then to "PILOT"
b) keep depressing the control knob, put long stem lighter into the
Ignition Hole on the emitter screen to light the pilot.
c) repeat step 4.
7) Push in and turn control knob to "LOW" position,
release knob then turn to low. If you want a higher temperature, push in
the control knob and turn counter clockwise to the "HIGH" position.
counter clockwise
Ignition Hole
Emitter Screen
10
The installation must conform with local codes or, in the absence of local codes, with the most current
version of the National Fuel Gas Code, ANSI Z223.1

OPERATIONOPERATION
Well Traveled
CAUTION :
Avoid inhaling fumes emitted from the heater's
first use. Smoke and odor from the burning of oils used in
manufacturing will appear. Both smoke and odor will
dissipate after approximately 30 minutes. The heater
should NOT produce thick black smoke.
""OW
""OW
NOTE:
When heater is ON:
The burner may be noisy when initially turned on. To eliminate excessive
noise from the burner, turn the Control Knob to the LOW position. Then,
turn the knob to the level of heat desired.
Emitter screen will become bright red due to intense heat. The color is more
visible at night. Burner will display tongues of blue flame. These flames
should not be yellow or produce thick black smoke, indicating an obstruction
of airflow through the burners.
RELIGHT
1)Turn the control knob to OFF position.
2)Wait five (5) minutes before attempting to relight pilot.
3) Repeat steps beginning with step 2 above.
SHUT DOWN INSTRUCTIONS
1) Push in and turn control knob clockwise to "OFF" position.
2) Turn L.P. tank gas valve clockwise to "OFF" position when
heater is not in use
: After use, some discoloration of the emitter screen is normal.Note
WARNING :Heater will be hot after use.
Handle with extreme care.
P
u
s
h
t
o
t
u
r
n
O
F
F
H
I
G
H
L
O
W
I
G
N
I
T
E
P
I
L
O
T
P
u
s
h
t
o
t
u
r
n
O
F
F
H
I
G
H
L
O
W
I
G
N
I
T
E
P
I
L
O
T
The Event of Gas Leakage
""OW
2)Turn LP cylinder to OFF position.
3)Wait 5 minutes to allow gas to dissipate.
4)If odor continues, immediately call gas supplier.
""OW
1)Turn the control knob to OFF position.
If the flame is very small, this is because the supply pressure
is not enough.
Operation Pressure Checked
1)Turn the control knob to "OFF" position and Turn LP cylinder to
"OFF" position.
2)Never leave the patio heater unattended while in use.
Before Leaving
11

12
LOCATING HEADER FOR USE
24"
18"
24"
Figure 1
This heater is primarily used for the
heating of outdoor patios, decks, spas, pool
and open working areas.
Always make sure that adequate fresh air
ventilation is provided. Follow the spacing
tolerances shown in Figure 1.
The minimum clearances, shown in Figure 1,
must be maintained at all times.
The installation must conform to local codes,
or in the absence of local codes, with the
standard for the storage and handling of
liquid petroleum gases, ANSI/NFPA 58-1986,
or most recent addition. For Canada, with the
current CAN1-B149.
This heater must be placed on level, firm
ground.
Never operate in an explosive atmosphere.
Keep away from areas where gasoline or
other flammable liquids or vapors are stored
or used.
Well Traveled
BE CAREFUL: WHEN CERTAIN
MATERIALS OR ITEMS ARE LEFT,
ABOVE, BESIDE OR UNDER THIS
HEATER WHILE IN USE, THEY WILL
BE SUBJECT TO RADIANT HEAT
AND COULD BE SERIOUSLY
DAMAGED.

13
MAINTENANCE/STORAGE
WARNING
DO NOT touch or move heater for at least 45
minutes after use.
Allow all burner elements to cool before
touching.
FOR YOUR SAFETY :
NOTE
In a salt-air environment (such as near an
ocean). corrosion occurs more quickly than
normal. Frequently check for corroded areas
and repair them promptly.
NOTE
Wait until heater is cool before covering.
Well Traveled
CLEANING AND MAINTENANCE :
To enjoy years of outstanding performance from your heater make sure
you perform the following maintenance activities on a regular basis:
Keep exterior surfaces clean.
Use warm soapy water for cleaning. Never use flammable of
corrosive cleaning agents.
While washing your unit, be sure to keep the area around the burner
and pilot assembly dry at all times. If the gas control is exposed to
water in any way, do NOT try to use it. It must be replaced.
Air flow must be unobstructed. Keep controls, burner, and circulating
air passageways clean. Signs of possible blockage include:
Gas odor with extreme yellow tipping of flame.
Heater does NOT reach the desired temperature.
Heater makes popping noises.
Heater glow is excessively uneven.
Spiders and insects can nest in burner or orifices. This dangerous
condition can damage heater and render it unsafe for use. Clean
burner holes by using a heavy-duty pipe cleaner. Compressed air may
help clear away smaller particles.
Carbon deposits may create a fire hazard. Clean dome and engine with
warm soapy water if any carbon deposits develop.
S:TORAGE
Between uses:
During periods of extended inactivity or when transporting;
Turn the control knob to "OFF" position.
Turn LP cylinder to "OFF" position.
Store heater upright in an area sheltered from direct contact with
inclement weather (such as rain, sleet, hail, snow, dust and debris).
If desired, cover heater to protect exterior surfaces and to help prevent
debris in air passages.
Turn the control knob to "OFF" position.
Disconnect LP Cylinder and move to a secure, well-ventilated location
outdoors. Do NOT store in a location that will exceed 125 degrees F.
Store heater upright in an area sheltered from direct contact with
inclement weather (such as rain, sleet, hail, snow, dust and debris).
If desired, cover heater to protect exterior surfaces and to help prevent
debris in air passages.

14
TROUBLESHOOTING
PROBLEM PROBABLE CAUSE SOLUTION
Pilot will not light Gas valve may be OFF Turn the gas valve ON
Orifice blocked Clean or replace Orifice
Air in supply system Purge air from lines
Loose connection Check all fittings
Pilot will not stay on Debris around pilot Clean dirty area
Loose connection Tighten connection
Thermocouple bad Replace Thermocouple
Gas leak in line Check connections
Burner will not light Pressure is low Fuel tank is near empty
Orifice blocked Remove, clean and replace
Control Valve not ON Turn valve to ON
Thermocouple bad Replace Thermocouple
Pilot light assembly bent
or not in correct location
Place pilot in proper
position and retry
Fuel T empty Refill LP gas tankank
Lack of fuel pressure Fuel tank is near empty
Well Traveled

15
WARRANTY
LIMITED PRODUCT WARRANTY:
Well Traveled Living
716 South 8th Street
Amelia Island, FL 32034
USA
1-800-766-9633
Well Traveled
Well Traveled Living
716 South 8 Street
Amelia Island, FL 32034
USA
1-800-766-9633
This manual is printed in China
PatioHeater-WTL Instructns.CDR 06-2004
Our products have been manufactured under the highest
standards of quality and workmanship. We warrant to the
original consumer purchaser that all aspects of this product
will be free of defects in material and workmanship for
one (1) year from the date of purchase. A replacement for any
defective part will be supplied free of charge for installation
by the consumer. Defects or damage caused by the use of
other than genuine parts are not covered by this warranty.
This warranty shall be effective from date of purchase as
shown on the purchasers receipt. Some states do not allow
limitations on how long an implied warranty lasts, so the
above limitation may not apply to you.
This warranty is valid for the original consumer purchaser
only and excludes industrial, commercial or business use of
the product, product damage due to shipment or failure which
result from alteration, product abuse, or product misuse,
whether performed by a contractor, service company, or
consumer. We will not be responsible for labor charges and/or
damage incurred in installation, repair or replacement, nor for
incidental or consequential damage.
This warranty gives you specific legal rights and you may
also have other rights which may vary from state to state,
province to province, and nation to nation. If you are not
satisfied with the performance or the quality of this product,
the valid refund period is 30 days after the date of purchase.
Any return after this period will not be allowed. You may call
us or simply write to us using the address below. Explain the
defect and include proof of purchase and your name, address
and telephone number. We will advise you of the procedure
to follow in making warranty claims.
th