Wenger Legacy Classic User manual

Assembly Instructions
-
/
!''$)'(!!!
$( Please read and understand these Assembly Instructions for the Legacy Classic Acoustical
Shell before assembling the parts.
$( Refer to the illustrations on the following pages. If you need additional information, write or
telephone Wenger Corporation at the number below.
contents
©Wenger Corporation 2011 Printed in USA 10/11 Part #186H191-01
#&$&%$&($# 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
Questions? Call.....USA: 800-4WENGER (493-6437) • Worldwide: 1-507-455-4100 • www.wengercorp.com
Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . .2
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Before Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

2
The Legacy Classic Acoustical Shell is guaranteed free of defects in materials and workmanship for five
full years.
Our guarantee assures you of either a full refund or repair or replacement of the defective materials or
workmanship without charge, at the discretion of our Customer Service Department. Just call a
Customer Service Representative at 1-800-887-7145 and state the reason you are dissatisfied. If a
product return is necessary, your representative will issue a return authorization. This is your sole
remedy for breach of this warranty.
Should you have a question or problem with any Wenger product, don’t hesitate to call, even if the
product is past warranty. It’s important to us that all our customers be satisfied.
This is the sole warranty made by Wenger. Wenger disclaims all other warranties, including the
warranties of merchantability and fitness for a particular purpose, as well as all liability for incidental,
consequential, special, and indirect damage. Wenger liability for direct damages shall be limited to the
amount you paid for the product involved. Wenger reserves the right to make product changes without
obligation to incorporate such changes into products previously sold.
Some states do not allow the exclusion or limitation of damages or warranties, so the above may not
apply to you. This warranty gives you specific legal rights. You may also have other rights which vary
from state to state.
WArrAnty
importAnt user informAtion

Copyright © 2010 by Wenger Corporation
All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted in
any form or by any means including graphic, electronic, or mechanical methods or photocopying,
recording, or information storage and retrieval systems without the written permission of the publisher,
unless it is for the purchaser's personal use.
Printed and bound in the United States of America.
The information in this manual is subject to change without notice and does not represent a commitment
on the part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any
errors that may appear in this manual.
In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for
direct, indirect, special, incidental, or consequential damages resulting from the use or defect of this
manual.
The information in this document is not intended to cover all possible conditions and situations that might
occur. The end user must exercise caution and common sense when assembling or installing Wenger
Corporation products. If any questions or problems arise, call Wenger Corporation at 1-800-733-0393.

The Legacy Classic Acoustical Shell is manufactured by:
Wenger Corporation
555 Park Drive
Owatonna, MN 55060
1-507-455-4100 • 1-800-733-0393
www.wengercorp.com
 
•This product is designed to be an acoustical reflector for vocal or instrumental groups. Towers may
also be used as a backdrop or as a screen for other functions such as speeches and ceremonies.
•This product is intended for indoor use in normal ambient temperature and humidity conditions.
•This product is intended to be assembled only as described in these instructions.

3
1. Remove the Hardware Box and check the contents.
It should contain the following:
Assembly
&+&
$,
2 Casters with 4" Wheels
85/16-18” Hex Nuts
85/16-18 x 3/4" Carriage Bolts
10 3/8-16 Hex Nuts
43/8-16 x 1" Carriage Bolts
63/8-16 x 2-1/4" Carriage Bolts
Do not remove the crate or Counterweight Assembly until instructed to do so.
Units should be assembled indoors, in a well-lighted space with a level floor. Choose an area
close to the performance space - a backstage scene shop is ideal. Make sure units will fit through
any doors between the assembly area and the performance space.
It is recommended that two people are used in the assembly process. Assemblers must be strong
enough to position the components for assembly.
before Assembly
The following tools are required to assemble the Legacy Classic Acoustical Shell:
required tools
•1/2" Wrench
•9/16" Wrench
•Cordless Drill with Phillips Head Bit
•Utility nife (to cut plastic wrap)
•Saw (to cut pallet).
sAfety precAutions
Make su e that anyone
wo king on the Legacy
Classic Acoustical Shell
has ead and unde stands
this manual.
!cAution
Failu e to comply with
Wa nings and Cautions in
this document can esult in
damage to p ope ty o
se ious inju y.
!cAution
Always obse ve and comply
with the Wa nings and
Cautions posted on the
system equipment.
!cAution
Throughout this manual you will find cautions and warnings which are defined as follows.
.  means that failure to follow the instruction may result in serious injury or death.
.  means that failure to follow the instruction may result in serious injury or damage to property.
Read all of these safety instructions before setting up the Legacy Acoustical Shell components.

4
2. Remove and discard the large piece of protective
cardboard from the Main Assembly.
3. Remove and discard the Support Bracket attached
to each Frame Upright.
Each Support Bracket is attached to the Frame
with a Lag Screw, a Fiber Washer, a Flat Washer
and a Lock Nut.
Assembly continued
)%%$&(
& ('
'(#&'
&$((*
&$&
Do not unband the Main
Assembly until it is
completely assembled and
the pallet is emoved.
!cAution

5
4. Remove the two Side Frames from the Counterweight Assembly
by cutting the bands securing them.
Discard the banding and foam padding.
5. Attach the Side Frames to the Counterweight Assembly
using two 3/8-16 x 1" Carriage Bolts and two 3/8-16 Hex Nuts
in each.
Assembly continued
&&
$!('
,
)('
)(
#'

&"'
&&
$!('

6
6. Using assistance, lift the Counterweight Assembly off
of the crate and down to the floor.
7. Move the Counterweight Assembly to
the back side of the shell.
A lift jack may be used if available.
8. Attach the Counterweight Assembly to the Frame
using three 3/8-16 x 2-1/4" Carriage Bolts and
three 3/8-16 Hex Nuts on both sides.
NOTE: The Carriage Bolts are to be inserted from
the outside of the Frame with the threaded
end toward the Counterweight Assembly.
&&
$!('
,
)('
&&
$!('
Counte weight Assembly is
heavy. Do not attempt to lift
without assistance.
!cAution
Assembly continued

7
9. Use a saw to make a single cut through the pallet as shown below.
10. Remove the four screws securing the Frame to the cut-away
section of the pallet.
11. Remove the cut-away section of the pallet.
12. Attach a Caster to the Frame as shown using four 5/16-18 x 3/4"
Carriage Bolts and four Hex Nuts.
NOTE: Be sure the Hex Nuts are installed on the
underside of the Caster.
Assembly continued
+)(
(
)(+-
($#$
!!(
"$*
&+'
'(&
,)('
&&
$!('

8
13. Repeat steps #9 through #12 for the other side of the shell.
14. Remove the remaining center pallet section.
15. Remove any remaining plastic wrapping, banding, tape or packing.
Assembly continued
'(&
,)('
&&
$!('