WerkMaster Scarab User manual

!!
WerkMaster Grinders and Sanders Inc.
6932 Greenwood Street, Burnaby, BC V5A 1X8
tel: [phone] | toll free: 1.866.373.WERK | fax: [phone]
www.werkmaster.com | email: [e-mail]
!
!
!
!
!
!
!
!
!
!
!!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
OPERATOR’S MANUAL
IMPORTANT: Read before using your new Scarab™/Gator
© Copyright 2013

!!
LIABILITY LIMITATIONS
The remedies of the user set forth under provisions of warranty outlined at the
end of this manual are the exclusive and total liability of WerkMaster Grinders &
Sanders Inc. with the respect to their sale or the equipment and service furnished
hereunder, in connection with the performance or breach thereof, or from the
sale, delivery, installation, repair or technical direction covered by or furnished
under the sale, whether based on contract, warranty, negligence, indemnity, strict
liability, or otherwise shall not exceed the purchase price of the unit of equipment
upon which such liability is based.
WerkMaster will not in any event be liable to the user, any successors in interest
or any beneficiary or assignee relating to this sale for any consequential,
incidental, indirect, special or punitive damages arising out of this sale or any
breach thereof, or any defects on, or failure of, or malfunction of the equipment
under this sale based upon loss of use, lost profits or revenue, interest, lost
goodwill, work stoppage, impairment of other goods, loss by reason of shutdown
or non-operation, increased expenses of operation of the equipment, cost of
purchase or replacement power of claims of users or customers of the user for
service interruption whether or not such loss or damage is based on contract,
warranty, negligence, indemnity, strict liability, or otherwise.
WerkMaster reserves the right to modify, alter and improve any part or parts
without incurring any obligation to replace any part or parts previously sold
without such modified, altered or improved part or parts.
No person is authorized to give any other warranty or to assume any additional
obligation on WerkMaster’s behalf unless made in writing and signed by an
officer of WerkMaster.
As a condition of these warranties, you are responsible for properly using,
maintaining, and caring for your machine as outlines in this Owner’s Manual.
WerkMaster recommends that you maintain copies of all maintenance records
and receipts for review by WerkMaster.
USE ONLY GENUINE WERKMASTER PARTS AND ACCESSORIES FOR
YOUR OWN SAFETY, THE SAFETY OF OTHERS AND THE LIFE OF YOUR
MACHINE. THIS WARRANTY IS NOT VALID IF YOUR MACHINE HAS BEEN
MODIFIED WITHOUT WERKMASTER’S AUTHORIZATION OR REPAIRED
WITH UNAUTHORIZED REPLACEMENT PARTS.

OPERATOR’S)MANUAL))
Page!III!)
CONTENTS)
INTRODUCTION........................................................................ 1
MACHINE DESCRIPTIONS....................................................... 1
SPECIFICATIONS ..................................................................... 1
SAFETY PRECAUTIONS .......................................................... 2
Personal Safety .............................................................................. 2
Physical and Mental Fitness ......................................................... 2
Safe Operating Distance................................................................ 2
Work Area Safety............................................................................ 3
Safety Rules.................................................................................... 3
Modifications .................................................................................. 3
ATTACHING MACHINE TO DRIVER........................................4
Compatible Variable Speed Polishers.......................................... 4
PRE-OPERATION INSTRUCTIONS.......................................... 6
MACHINE OPERATION ............................................................ 7
Attaching Full Plate Tooling …….…………………………………...7
Attaching Resin Tooling/Sanding Discs……………………………8
Changing to Low Profile Pad Driver………………………………...8
Adjusting the Dust Skirt……………………………………………….9
Attaching the Vacuum………………………………………………..10
Starting the Machine………………………………………………….10
Setting the Speed…...………………………………………………...10)
WATER FEATURE PORT ....................................................... 11
EDGING ................................................................................... 11
!Edging with the Scarab..……………………………………………11
Edging with the Gator .……………………………………………..12
CLEANING AND MAINTENANCE .......................................... 12
STORAGE................................................................................ 12
TROUBLESHOOTING/TECH SUPPORT................................ 12
EXPLODED VIEWS AND PARTS LISTS………………………13
OPTIONAL ACCESSORIES……………………………………..17
WARRANTY ……………………………………………………..18
!
!

OPERATOR’S)MANUAL))
Page!1!)
!
INTRODUCTION
Congratulations on your purchase of a WerkMaster Scarab/Gator. WerkMaster
machines allow professional surface prep, polishing, grinding, edging, buffing
and restoration of virtually any surface material including concrete, terrazzo,
stone, vinyl, and hardwood. This manual is provided to assist you in the
operation and maintenance of your WerkMaster equipment.
MACHINE DESCRIPTION
WerkMaster machines include the SCARAB, GATOR, RASP, THE EDGE,
MIROIR, COBRA, PYTHON, RAZOR, TITAN XT, and COLOSSOS XT models.
To see the complete family of WerkMaster machines visit our website at
www.werkmaster.com.
SCARAB
•Ideal handheld machine for floors, stairs, ledges and countertops
•Edges to 1/8” of the wall and right to the edge of the countertop
•90° head rotation is designed to get into tight places and small spaces
•Grinds, strips, sands, polishes, buffs, burnishes and edges
•Excellent for concrete, stone, terrazzo and vinyl tile
•Works with the Milwaukee, Metabo, DeWalt and Flex variable speed
polishers
•The Octi-Disc™ self-balancing 5 head system is used with our 3” (76 mm)
full plate diamond abrasive metal bond tooling, resins, and buffing pads
•Easily go from dry grinding and polishing to wet polishing and cutting
•Can be easily converted for use on hardwood
GATOR
•Ideal handheld machine for hardwood floors, stairs, ledges and butcher block
countertops
•Gets under 3.5” (89mm) kicks
•Edges up to 1/8” (3mm) of the wall and right to the edge of the countertop
•90° head rotation is designed to get into tight places and small spaces
•Preps, strips, sands, polishes, buffs, burnishes and edges
•Works with the Milwaukee, Metabo, DeWalt and Flex variable speed
polishers
•The Octi-Disc™ self-balancing 5 head system is used with our 3” (76 mm)
full plate diamond abrasive metal bond tooling, resins, and buffing pads
•Can be easily converted for use on concrete, stone, terrazzo and vinyl tile!
SPECIFICATIONS
MODEL
SCARAB
GATOR
Footprint in/cm
12 x 8 x 7 / 31 x 20 x 18
12 x 8 x 3.5 / 31 x 20 x 8.9
Weight lbs/kg
20 / 9.1 w/o polisher
20 / 9.1 w/o polisher
Disc Size in/cm
3 (7.6)
3 (7.6)
Speed Range
RPM
See polisher manual for
speed range
See polisher manual for
speed range

OPERATOR’S)MANUAL))
Page!2!)
!
SAFETY PRECAUTIONS
!
!
!
!
!
Read this manual and all safety precautions before attempting to operate
your WerkMaster Scarab/Gator. Failure to follow the safety precautions
may result in electric shock, fire and/or serious injury. This product is
intended for commercial use.
The term “variable speed grinder/polisher” refers to your main-operated (corded)
power tool or battery operated (cordless) power tool. ALWAYS refer to the
variable speed grinder/polisher manual when using the Scarab/Gator.
!
!
•Wear eye and ear protection at all times when operating WerkMaster
machines. Use only ANSI/OSHA approved safety glasses to help
prevent eye injury.
•Wear appropriate clothing and footwear when operating WerkMaster
machines. Do not wear loose clothing or jewelry that can become
entangled in moving parts.
•Safety equipment such as dust mask, non-skid safety shoes, hard hat,
or hearing protection used for appropriate conditions will reduce
personal injuries.
•Avoid accidental starting. Ensure the switch is in the OFF position before
plugging in. Do not carry power tools with your finger on the switch or
plug in power tools that have the switch on.
•Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may
result in personal injury.
•Do not overreach. Keep proper footing and balance at all times.
•Always use a vacuum.
•Ensure the variable speed grinder/polisher is properly connected to the
Scarab/Gator and follow all operating procedures.
•Keep handles dry, clean and free from oil and grease.
!
•Never operate WerkMaster machines under the influence of drugs or
alcohol, when taking medications that impair the senses or reactions, or
when excessively tired or under stress.
!
•WerkMaster machines are to be operated by one person at a time.
Maintain a safe operating distance from other persons. Keep bystanders
a safe distance away during operation by blocking off the work area in all
directions with roping, safety netting, or other material. Failure to do so
may result in someone being injured by flying debris or being exposed to
harmful dust and noise.
•Maintain a safe operating distance from flammable materials. Sparks
from the cutting action of WerkMaster machines may ignite flammable
materials or vapors.
!
!
Personal Safety
Physical and
Mental Fitness
Safe Operating Distance
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! )WARNING)

OPERATOR’S)MANUAL))
Page!3!)
!
•Keep work area clean and well lit.
•Turn the Scarab/Gator OFF before disconnecting power.
•DO NOT disconnect power by pulling the cord; grasp the plug, not the
cord. To remove twist-lock plugs, push in and turn clockwise to engage,
and turn counter-clockwise and pull to remove.
!
•ALWAYS refer to the variable speed grinder/polisher manual for safe
operation
•DO NOT let comfort or familiarity with this tool (gained from repeated
use) replace strict adherence to polisher safety rules. If you use this tool
unsafely or incorrectly, you may suffer serious personal injury.
•Running accessories over rated speeds may cause injury.
•Firmly secure any loose surface before operating the Scarab/Gator. Do
not use your hand or body to secure loose surfaces.
•Hold the tool firmly with both hands. Do not drop. Be sure to keep
the Scarab/Gator level or flat with the surface, using smooth and
continuous movement. Avoid objects projecting out of the solid surface
you are working on as they may cause damage to the tooling.
•Keep hands away from rotating parts.
•When sanding metallic surfaces, the operator should watch for
flying sparks. Hold the tool so that the sparks fly away from you, other
persons and flammable materials.
•DO NOT leave the tool running.
•DO NOT touch the work surface immediately after operation; it may be
hot.
•Ventilate your work area adequately when operating a Scarab/Gator.
ALWAYS use an appropriate dust collection system.
•Use of this tool to sand or grind could expose user to dust containing
hazardous substances. Use appropriate respiratory protection.
•Risk of Explosion: Sanding can result in an explosive mixture of fine dust
and air. Use sanding machines only in well-ventilated area free from any
flame or match.
!
•DO NOT modify WerkMaster machines. Modifications will void the
warranty and may result in injury to persons and damage to the
machine.
!
!
!
!
!
!
!
!
Work Area Safety
Safety Rules
Modifications

OPERATOR’S)MANUAL))
Page!4!)
!
ATTACHING SCARAB/GATOR TO DRIVER
!
Do not attempt to attach the Scarab/Gator with your variable speed polisher
plugged in.)
!
!
•Milwaukee™ 5540
•Metabo™ PE 12–175
•DeWalt TM!!!DWP849X
•Flex™ LK603VVB
Always refer to the variable speed polisher manual.
When numbers indicated in brackets please refer to Exploded View and Parts
List of Scarab (S) on page 13 and Gator (G) on page 15.
1. Choose the adapter ring that corresponds to your variable speed polisher.
D-DeWalt™ E-Metabo TM F-Flex™ M-Milwaukee™
!
(S-38) (S-22) (S-23) (S-25)
(G-38) (G-19) (G-20) (G-22)
!
!
!
!
2. Position the ring so that the outer lip is away from the polisher.
!
!
!
!
!
!
!
!
!
!
!
!
!
Compatible Variable Speed
Polishers
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! )WARNING)
(S-34)
(G-28)

OPERATOR’S)MANUAL))
Page!5!)
!
3. Depending on whether the arbor on your polisher is Metric or Imperial,
thread the appropriate arbor extension into the Scarab/Gator.
M–Metric (S-5 G-2) or I–Imperial (S-20 G-18) will be stamped on the arbor.
!
!
!
!
!
!
!
!
!
!
!
!
!
!!!!!!!!!NOTE: If using a Milwaukee polisher extension (S-34 G-28) is required.
!
4. Thread the arbor of the variable speed polisher into the arbor extension,
leaving a very small gap between the two.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
5. Place the coupler halves (S-12,13 G-9,10) around the mounting rings. To fit
all the grooves into place you may need to adjust the gap between the arbor
and the arbor extension. Insert and tighten bolts (S-1 G-1) to hold everything
in place.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!

OPERATOR’S)MANUAL))
Page!6!)
!
PRE-OPERATION INSTRUCTIONS
!
1. Choose surface type.
!
!
!
!!!!!Concrete Terrazzo Stone Wood Vinyl
For Concrete ONLY:Test the concrete surface using the MOHS Hardness Test
Kit. Watch the video ‘How to use a MOHS Hardness pick test kit’ under
Videos/Training Videos at www.werkmaster.com.
2. Choose tooling. For a list of tooling options see the Machine Specific Tooling
Guide under Products/Machines/Scarab or Products/Machines/Gator at
www.werkmaster.com.
3. Practice on a test surface is recommended.
!

OPERATOR’S)MANUAL))
Page!7!)
!
MACHINE OPERATION
ALWAYS ensure the variable speed polisher is unplugged when changing
tooling.
SCARAB
1. Tooling can be removed by hand.
2. Firmly grasp the Full Plate tooling, align the two shear pins with the two
corresponding grommets and insert.
NOTE: ALWAYS have compression foam between the pad driver and the
tooling plate.
3. Ensure that each tooling piece is flush with the pad driver.
GATOR
1. Tooling can be removed by hand.
2. Attach the 3” loop backed tools directly onto the GATOR pad driver.
Attaching)Full)Plate)
Tooling)

OPERATOR’S)MANUAL))
Page!8!)
!
ALWAYS ensure the variable speed polisher is unplugged when changing
tooling.
SCARAB
1. Firmly grasp the Full Plate tooling and remove by pulling it out from the rubber
grommets. Select the foam/hook adapter plate and insert the two shear pins into
the corresponding grommets. Center loop-backed resin tooling onto the
foam/hook adapter plate.
NOTE: ALWAYS have compression foam between the pad driver and
Foam/Hook Adapter plate.
GATOR
1. Center the 3” Hook and Loop pad onto the pad driver. Then center the
sanding disc onto Hook and Loop pad.
To Remove simply separate loop-back tooling from hook adapter plate.
SCARAB GATOR
Foam/Hook Adapter Sanding Disc and Hook/Loop Pad
The Low Profile Pad Driver is standard on the Gator.
The Low Profile Pad Driver (sold separately) reduces the height profile of the
Scarab enabling it to get under kicks and other height restricted areas.
If converting the Scarab to Low Profile:
ALWAYS ensure the variable speed polisher is unplugged when changing the
pad driver. !
1. Remove the full plate tooling or the adapter plate and the compression
foam.
2. To remove the pad driver use a 17mm socket wrench. Slip it over the
pad driver bolt and strike the wrench with a soft face mallet in a counter-
clockwise direction to loosen the bolt; then remove the bolt.
Attaching)Resin)
Tooling)/)Sanding)
Disc)
Changing)to)Low)
Profile)Pad)Driver)
on)the)Scarab)

OPERATOR’S)MANUAL))
Page!9!)
!
3. Attach the Low Profile Pad Driver, applying a generous amount of blue
threadlocker compound (Loctite 243) to the bolt and the threaded drive
shaft. Insert the bolt through the hole in the pad driver.
NOTE: Reapply blue threadlocking compound (Loctite 243) every time a
pad driver is removed.
4. Line up the bolt to the threaded end of the shaft and start the first couple
of threads.
5. Once the bolt is engaged, make sure the drive shaft is properly seated
within the pad driver slot before tightening the bolt all the way.
!
!
Failure to seat the pad driver could result in the pad driver slot being damaged,
the threads in the shaft being stripped, the machine leaving heavy tool marks,
and the tooling overheating.
Ensuring the Dust Skirt is level with the tooling helps direct dust particles to the
vacuum port, as well as protect the operator and surrounding objects from harm
or damage from possible projected objects.
1. The Dust Skirt is divided into 3 pieces: left, right and back. All pieces are
held in place by a hook perimeter on the Scarab/Gator and loop on the inside
of the Dust Skirt and 3 outside connecting flaps.
2. Adjust all 3 pieces so that they are level with the height of the tooling. Secure
all 3 pieces with the outside connecting flaps.
NOTE: There will be a gap between the left and right pieces at the front of
the Scarab/Gator. THIS IS NORMAL. The outside flap secures the left and
right pieces. The gap allows the operator to get closer into corners.
3. Remove the left or right piece to get closer to the wall.
!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! ))CAUTION)
Adjusting)the)
Dust)Skirt)

OPERATOR’S)MANUAL))
Page!10!)
!
! !
1. Use a 1½” (38 mm) hose reducer (sold separately) between the vacuum
port to fit a standard 2” (51 mm) vacuum hose.
2. ALWAYS run a vacuum while dry grinding.
NOTE: ALWAYS refer to the vacuum manual.
!
!
1. Set the speed on the polisher to LOW.
2. Securely grip the handle prior to turning variable speed polisher ON.
3. Squeeze trigger to start.
4. Release trigger prior to lifting off surface.
5. Unplug the machine and wait until the tooling plates come to a complete stop
prior to making any adjustments.
NOTE:ALWAYS refer to the variable speed polisher manual.!
!
!!!
!
!
!
TOOLING
SPEED
Metal Bond
Low
Resins
Medium
Polishing
High
Sandpaper
Low
!
!
!
!!!!!!
!
!
Starting)the)
Machine)
Setting)the)
Speed)
Attaching)the)
Vacuum)

OPERATOR’S)MANUAL))
Page!11!)
!
WATER FEATURE PORT
!
!
!
Use extreme caution when working with electricity and water. Severe injury
or death may occur if caution is not used.
NOTE: The Water Feature is sold separately.
1. ALWAYS refer to the variable speed polisher manual prior to using the
water feature
2. Insert water feature plug into the vacuum port.
3. Ensure the blue flow control valve is in the OFF position.
4. Attach a ¾” threaded male hose end to the ¾” female end of the water
feature. To prevent leaks, secure tightly with a new washer.
5. Turn on water supply. Adjust the blue flow control valve as wet grinding
process requires.
EDGING WITH THE SCARAB
The SCARAB edges to within 1/8” (3 mm) of the wall and right to the edge of
countertops.
1. DO NOT run Scarab right off the edge of countertops as the tooling may
eject possibly causing harm or damage.
A video demonstration of the Scarab edging can be viewed at
www.werkmater.com Products/Machines/Scarab.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!)DANGER)

OPERATOR’S)MANUAL))
Page!12!)
!
EDGING WITH THE GATOR
The GATOR edges to within 1/8” (3 mm) of the wall and right to the edge of
butcher block countertops.
1. DO NOT run the Gator over open holes in the floor such as forced air vents.
2. DO NOT run the Gator right off the edge of countertops as the tooling may
eject possibly causing harm or damage.
A video demonstration of the Gator edging can be viewed at
www.werkmater.com Products/Machines/Gator.
CLEANING AND MAINTENANCE
The WerkMaster Scarab/Gator requires minimal maintenance.
1. Remove tooling after each use.
2. Vacuum and wipe clean of any built-up debris.
STORAGE
Store Scarab/Gator and tooling in a dry, non-corrosive environment.
!
!
TROUBLESHOOTING/TECH SUPPORT
!
For technical support, email [email protected], fill out a Request for
Technical Support Form or phone [phone], toll free at 1.866.373.WERK.!
!
!
!
!
!
!
!
!
!
!
!

OPERATOR’S)MANUAL))
Page!13!)
!
EXPLODED VIEWS & PARTS LISTS
!!!!!!!!SCARAB 001-0064-00!
) ) ) ) ) !!!!!!)
!
!
!
!
!
!
!
!
)
!
!
!
!
!
!
!
!
!
!
!

OPERATOR’S)MANUAL))
Page!14!)
!
SCARAB PARTS LIST
ITEM
QTY
PART NUMBER
DESCRIPTION
1
4
590-0198-00
Fastener
2
1
100-0416-01
Handle Grip
3
2
100-0417-01
Handle, Side Plate
4
2
100-0476-00
Handle, Side Plate, DeWalt
5
1
100-0522-01
Coupler, Metric Adapter Shaft (M)
6
1
100-0512-01
Drive Train, Upper Shell
7
1
100-0407-01
Drive Train, Coupler Mount
8
1
100-0513-01
Drive Train, Lower Shell
9
1
520-0034-00
Belt
10
1
580-0257-00
Cord Gasket
11
2
100-0514-01
Drive Train, Idler Pin
12
1
100-0410-01
Coupler, Main Body, Part A
13
1
100-0411-01
Coupler, Main Body, Part B
14
1
110-0046-01
Vacuum Manifold Assembly
15
3
590-0193-00
Fastener
16
4
590-0197-00
Fastener
17
3
590-0209-00
Fastener
18
4
500-0229-00
Bearing
19
10
008-0040-00
Shear Pins
20
1
100-0521-01
Coupler, Imperial Adapter Shaft (I)
21
1
008-0624-00
Velcro Hook
22
1
100-0518-00
Coupler, Metabo Adapter Ring
23
1
100-0519-00
Coupler, Flex Adapter Ring
24
1
590-0211-00
Fastener
25
1
100-0811-01
Coupler, Milwaukee Adapter Ring
26
6
500-0012-00
Bearing
27
6
500-0006-00
Bearing
28
5
500-0230-00
Sprocket, Integrated Drive Shaft
29
1
500-0250-00
Sprocket, Integrated Input Shaft
30
1
580-0203-00
Sticker, Warning
31
1
580-0075-00
Decal
32
1
009-0040-00
Allen Key
33
1
580-0084-00
Serial Plate
34
1
100-0812-01
Coupler, Milwaukee Imperial Adapter Shaft
(EXT)
35
5
008-0279-01
3” Adapter Reinforcement Plate
36
5
008-0244-01
Adapter Plate Foam
37
10
590-0210-00
Fastener
38
1
100-0942-00
Coupler, DeWalt Adapter Ring (2015)
39
2
590-0065-00
Lock Washer
40
2
590-0045-00
Fastener
41
5
008-0259-01
3” Ultra Flex Pad Driver, Thin
42
5
590-0126-00
Fastener
43
10
008-0207-00
Grommet
44
10
008-0208-00
Bumper
45
5
008-0318-00
Suspension Foam
46
1
008-0639-00
Urethane Skirt, 3 pc, 3” W
47
5
008-0273-00
3” Adapter Plate Assembly
48
5
008-0280-00
3” Ultra Flex Pad Driver Assembly w Bolt
NOTE:SCARAB 001-0064-00 comes with Pad Driver #32 and Adapter Plate Assembly #34.
SCARAB 001-0084-00 comes with Pad Driver #35 and Adapter Plate Assembly #36.
NOTE: *Adapter Ring is dependent on make and model of variable speed polisher

OPERATOR’S)MANUAL))
Page!15!)
!
GATOR 001-0084-00

OPERATOR’S)MANUAL))
Page!16!)
!
GATOR PARTS LIST
ITEM
QTY
PART NUMBER
DESCRIPTION
1
4
590-0198-00
Fastener
2
1
100-0522-01
Coupler, Metric Adapter Shaft (M)
3
1
100-0512-01
Drive Train, Upper Shell
4
1
100-0404-01
Drive Train, Coupler Mount
5
1
100-0513-01
Drive Train, Lower Shell
6
1
520-0034-00
Belt
7
1
580-0257-00
Cord Gasket
8
2
100-0514-01
Drive Train, Idler Pin
9
1
100-0410-01
Coupler, Main Body, Part A
10
1
100-0411-01
Coupler, Main Body, Part B
11
1
100-0016-01
Vacuum Manifold Assembly
12
3
590-0193-00
Fastener
13
4
590-0197-00
Fastener
14
3
590-0209-00
Fastener
15
4
500-0229-00
Bearing
16
5
590-0126-00
Fastener
17
1
100-0521-01
Coupler, Imperial Adapter Shaft (I)
18
1
008-0624-00
Velcro Hook
19
1
100-0518-00
Coupler, Metabo Adapter Ring
20
1
100-0519-00
Coupler, Flex Adapter Ring
21
1
590-0211-00
Fastener
22
1
110-0056-02
Coupler, Milwaukee Adapter Ring
23
5
110-0055-02
Drive Shaft Assembly
24
1
100-0067-01
Input Shaft Assembly
25
1
580-0203-00
Sticker, Warning
26
1
009-0040-00
Allen Key
27
1
580-0084-00
Serial Plate
28
1
100-0812-01
Coupler, Milwaukee Imperial Adapter Shaft (EXT)
29
1
130-0056-00
Handle, Grip Assembly
30
5
008-0620-00
Adapter Rubber, Mushroom Hook w Loop
31
10
580-0242-00
Magnet
32
5
008-0612-00
3” Plug N Go Plate, Thick w Recess
33
10
008-0040-02
Shear Pins
34
5
008-0613-00
3” Plug N Go Plate, Tick w Recess Assembly
35
5
008-0611-00
3” Low Profile Pad Driver
36
5
008-0610-01
3” Pad Plate
37
1
580-0502-00
Decal
38
1
100-0942-00
Coupler, DeWalt Adapter Ring (2015)
39
1
008-0640-00
Urethane Skirt, 3 pc, 2.5” W
40
5
008-0609-00
Pad Driver Foam

OPERATOR’S)MANUAL))
Page!17!)
!
OPTIONAL ACCESSORIES
)))))))))PART NO. ITEM
008-0273-00 Foam/Velcro Adapter Plate, 3”
008-0620-00 Sanding Disc Adapter Plate, 3“
008-0318-00 Compression foam, 3” X ¼”
007-0006-00 MOHS Hardness Test Kit
!
!
!
!
!
005-0080-00 Universal Hose Adapter
!
!
010-0018-00 Water Feature!
!
!
!
!
008-0114-00 Scarab Shear Pin Assembly
008-0618-00 Gator Shear Pin Assembly