Weslo pursuit 360R WLEX1476.0 User manual

Serial Number
Decal
USERʼS MANUAL
www.weslo.com
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
Model No. WLEX1476.0
Serial No.
Write the serial number in the
space above for reference.
QUESTIONS?
If you have questions, or if parts are
damaged or missing, DO NOT
CONTACT THE STORE; please
contact Customer Care.
IMPORTANT: Please register this
product (see the limited warranty
on the back cover of this manual)
before contacting Customer Care.
CALL TOLL-FREE:
1-866-699-3756
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
www.wesloservice.com

2
TABLE OF CONTENTS
WARNINGDECA P ACEMENT ..............................................................2
IMPORTANTPRECAUTIONS ................................................................3
BEFOREYOUBEGIN ......................................................................4
ASSEMB Y ...............................................................................5
HOWTOUSETHEEXERCISECYC E .......................................................10
MAINTENANCEANDTROUB ESHOOTING ...................................................14
EXERCISEGUIDE INES ...................................................................15
PART IST ..............................................................................18
EXP ODEDDRAWING ....................................................................19
ORDERINGREP ACEMENTPARTS ..................................................BackCover
IMITEDWARRANTY ..............................................................BackCover
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the
warning decal(s). If a decal is missing or
illegible, see the back cover of this
manual and request a free replacement
decal. Apply the decal in the location
shown. Note: The decal(s) may not be
shown at actual size.
WES O is a registered trademark of ICON IP, Inc.

3
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your exercise cycle before using your exercise
cycle. ICON assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or per-
sons with pre-existing health problems.
2. Use the exercise cycle only as described in
this manual.
3. It is the responsibility of the owner to ensure
that all users of the exercise cycle are ade-
quately informed of all precautions.
4. The exercise cycle is intended for home use
only. Do not use the exercise cycle in a com-
mercial, rental, or institutional setting.
5. Keep the exercise cycle indoors, away from
moisture and dust. Place the exercise cycle
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is at least 2 ft. (0.6 m) of clearance
around your exercise cycle.
6. Inspect and properly tighten all parts regular-
ly. Replace any worn parts immediately.
7. Keep children under age 12 and pets away
from the exercise cycle at all times.
8. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the exercise cycle. Always wear
athletic shoes for foot protection.
9. The exercise cycle should not be used by
persons weighing more than 250 lbs.
(113 kg).
10. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
11. The exercise cycle does not have a free
wheel; the pedals will continue to move until
the flywheel stops.
12. Always keep your back straight while using
the exercise cycle; do not arch your back.
13. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
IMPORTANT PRECAUTIONS

4
Resistance Knob
Seat
Seat Handle
Adjustment Knob
Pedal/Strap
Console
Backrest
Seat Frame
Handlebar
Thumb Pulse Sensor
BEFORE YOU BEGIN
Thank you for selecting the new WES O®PURSUIT
360R exercise cycle. Cycling is an effective exercise
for increasing cardiovascular fitness, building
endurance, and toning the body. The PURSUIT 360R
exercise cycle provides a selection of features
designed to make your workouts at home more effec-
tive and enjoyable.
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
tions after reading this manual, please see the front
cover of this manual. To help us assist you, note the
product model number and serial number before con-
tacting us. The model number and the location of the
serial number decal are shown on the front cover of
this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.

5
ASSEMBLY
To hire an authorized service technician to assemble the exercise cycle, call 1-800-445-2480.
Assembly requires two persons. Place all parts of the exercise cycle in a cleared area and remove the pack-
ing materials. Do not dispose of the packing materials until assembly is completed.
In addition to the included tool(s), assembly requires a Phillips screwdriver , two adjustable
wrenches , and pliers .
Use the drawings below to identify the small parts used in assembly. The number in parentheses below each
drawing is the key number of the part, from the PART IST near the end of this manual. The number following
the parentheses is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if
it has been preassembled.
M10 Locknut
(65)–2
M8 Locknut
(10)–2
M8 Split
Washer (42)–3
M8 Washer
(54)–4
M6 Washer
(68)–8
M6 Locknut
(63)–4
M4 x 5mm
Self-tapping
Screw (66)–2
M4 x 8mm
Screw (29)–2
M6 x 35mm Button
Screw (61)–8
M10 x 75mm Carriage Bolt (30)–2
M10 x 60mm Button Screw (33)–2
M8 x 20mm Button
Screw (34)–3
M6 Curved
Washer (69)–4
M4 Washer
(70)–2
M6 x 15mm Button
Screw (46)–4
M6 x 30mm Button
Bolt (64)–4
M8 x 125mm Bolt (62)–2

6
3. Insert the end of the Seat Frame (5) into the
Frame (1).
Firmly press the Frame Bushing (56) into the
Frame (1). Attach the Frame Bushing to the
Frame with two M4 x 5mm Self-tapping Screws
(66).
Then, tighten the Adjustment Knob (9) into the
Frame (1).
Carefully tip the exercise cycle onto its side.
Attach the two Bumpers (57) to the Frame (1)
with two M4 x 8mm Screws (29) and two M4
Washers (70).
Then, tip the exercise cycle upright.
5
66
57
29
70
70
66
9
56
1
1.
Turn the Front Stabilizer (2) so that the large
holes are facing the Frame (1).
Attach the Front Stabilizer (2) to the Frame (1)
with two M10 x 60mm Button Screws (33).
2
33
arge
Holes 1
1
2. Attach the Rear Stabilizer (6) to the Seat Frame
(5) with two M10 x 75mm Carriage Bolts (30)
and two M10 ocknuts (65).
30
6
5
2
65
65
3
To make assembly easier, read the
information on page 5 before you begin.

7
6
61
61
68
68
68
15
14
60
6. Attach the Backrest (60) to the Seat Brackets
(14, 15) with four M6 x 35mm Button Screws
(61) and four M6 Washers (68).
See step 4. Tighten the two M8 ocknuts (10).
14 15
64
69
63
59
59
5
5. Attach a Seat Handle (59) to the round tube on
the eft Seat Bracket (14) with two M6 x 30mm
Button Bolts (64), two M6 Curved Washers (69),
and two M6 ocknuts (63).
Attach the other Seat Handle (59) to the
Right Seat Frame (15) in the same way.
4. Attach the eft and Right Seat Brackets (14, 15)
to the Seat Frame (5) with two M8 x 125mm
Bolts (62), four M8 Washers (54), and two M8
ocknuts (10) as shown. Do not tighten the
Locknuts yet.
4
5
54
54
14
54 54
10 10
15
62

8
8. While another person holds the Upright (13) in
the position shown, connect the Extension Wire
(52) to the Reed Switch Wire (43).
Next, connect the Resistance Cable (19) to the
ower Cable (45) in the following way:
•See drawing A. Pull upward on the metal
bracket on the ower Cable (45), and insert
the tip of the Resistance Cable (19) into the
wire clip inside the metal bracket as shown.
•See drawing B. Firmly pull the Resistance
Cable (19) upward and slide it into the top of
the metal bracket as shown.
•See drawing C. Using pliers, squeeze the
prongs on the upper end of the metal bracket
together.
Push the excess wire and cable downward into
the Frame (1), and insert the Upright (13) into
the Frame.
Tip: Avoid pinching the wires and cables.
Attach the Upright (13) to the Frame (1) with
three M8 x 20mm Button Screws (34) and three
M8 Split Washers (42).
ABC
45
19 19 Metal
Bracket
Metal
Bracket
45
1
13
45
19
52
34
34
42
42
8
43
7. Attach the Seat (12) to the Seat Brackets (14,
15) with four M6 x 35mm Button Screws (61)
and four M6 Washers (68).
7
12
68
61
68
68
15
14
61
Avoid pinching
the wires

9
11. Identify the eft Pedal (24), which is marked
with an “ ” sticker.
Using an adjustable wrench, firmly tighten the
eft Pedal (24) counterclockwise into the left
arm of the Crank (21).
Tighten the Right Pedal (not shown) clockwise
into the right arm of the Crank (21).
IMPORTANT: Tighten both pedals as firmly
as possible. After using the exercise cycle
for one week, retighten the pedals. For best
performance, keep the pedals tightened.
Adjust the left Pedal Strap (53) to the desired
position, and press the end of the Pedal Strap
onto the tab on the eft Pedal (24). Adjust the
right Pedal Strap (not shown) in the same
way.
24
Tab
53
21
11
12. Make sure that all parts are properly tightened before you use the exercise cycle. After assembly is com-
pleted, some extra parts may be left over. Place a mat under the exercise cycle to protect the floor.
10. While another person holds the Console (16)
near the Upright (13), connect the console wire
to the Extension Wire (52).
Then, insert the wires downward into the
Upright (13).
Tip: Avoid pinching the wires. Attach the
Console (16) to the Upright (13) with four M6 x
15mm Button Screws (46).
9
10
52
13
46
46
Console
Wire
16
16
Batteries
Battery
Cover
9. The Console (16) requires four AA batteries (not
included); alkaline batteries are recommended.
IMPORTANT: If the exercise cycle has been
exposed to cold temperatures, allow it to
warm to room temperature before inserting
batteries into the Console. If you do not do
this, the console displays or other electronic
components may become damaged. Remove
the battery cover and insert four batteries into
the Console as shown. Make sure that the bat-
teries are oriented as shown by the diagram
inside the Console. Then, reattach the battery
cover.
Avoid pinching
the wires

10
HOW TO USE THE EXERCISE CYCLE
HOW TO AD UST THE SEAT FRAME
For effective exer-
cise, the seat should
be in the proper
position. As you
pedal, there should
be a slight bend in
your knees when the
pedals are in the
most forward posi-
tion.
To adjust the seat
frame, first loosen
the adjustment knob
on the frame. Slide
the seat frame for-
ward or backward to
the desired position.
Then, retighten the
adjustment knob.
HOW TO AD UST THE PEDALING RESISTANCE
To increase the
resistance of the
pedals, turn the
resistance knob
clockwise; to
decrease the resis-
tance, turn the knob
counterclockwise.
IMPORTANT: Stop
turning the knob
when turning
becomes difficult,
or damage may
result.
Knob
Seat
Frame
Resistance
Knob