Weslo Body Flex User manual

QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts,
please call:
08457 089 009
Or write:
ICON Health & Fitness, Ltd.
Unit 4
Revie Road Industrial Estate
Revie Road
Beeston
Leeds
LS11 8JG
UK
[email protected]
Model No. WLEMBE14020
Serial No.
Write the serial number in the
space above for future reference.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
USER’S MANUAL
Part No.192762 R0605A Printed in China ©2004 ICON IP, Inc.
Serial Number Decal
www.iconeurope.com
Visit our website at
ORDERING REPLACEMENT PARTS
If you encounter any problems with this product, or if you need to order replacement parts, contact the ICON
Health & Fitness, Ltd. office, or write:
ICON Health & Fitness, Ltd.
Customer Service Department
Unit 4
Revie Road Industrial Estate
Revie Road
Beeston
Leeds
LS11 8JG
UK
Tel:
Outside the UK: 0 (044) 113 387 7133
Fax: [phone]
When ordering parts, please be prepared to give the following information:
• the MODEL NUMBER of the product (WLEMBE14020)
• the NAME of the product (WESLO®BODY FLEX)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see the PARTLIST and the EXPLODED DRAWING on
pages 10 and 11)
08457 089 009

112
33
34
34
18
18
13
13
5
16
16
15
15
32
32
45
45
33
35
36
46
20
32
43
43
42
35
10
10
9
8
11
7
35
35
32
6
36
48
11
31
47
19
11
4
19
35
32
32
44
11
3
26
1
41
39
39
12
12
21
22 23
25
12
22
39
49
30
29
28
27
24
26
25
12
17
14
38
39
40
37
21
22 23
37
37
38
40
37 14
2
40
38
21
23
39
41
39
41
39
39
41
40
38
12
21
22
23
39
39
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
EXPLODED DRAWING—Model No. WLEMBE14020 R0604A
WESLO is a registered trademark of ICON IP, Inc.

310
11 Seat
2 1 Seat Bracket
3 1 Rail
4 1 Stabiliser
5 1 Upper Bar
6 1 Support Leg
7 1 Adjustment Foot
8 1 Adjustment Leg
9 1 Adjustment Bracket
10 2 Adjustment Bushing
11 4 60mm Round Outer Cap
12 10 M8 Nylon Locknut
13 2 Foam Pad
14 2 25mm x 50mm Inner Cap
15 2 Large Pulley
16 2 Pulley Housing
17 2 Small Pulley
18 2 Round End Cap
19 2 Bumper
20 1 Support Leg Isolator
21 4 Wheel
22 4 Small Bushing
23 4 Large Bushing
24 1 Handlebar
25 2Inner Cap
26 2 Handgrip
27 1 Knob
28 2 Handle
29 2 Clip
30 1 Cord
31 1 M6 x 138mm Bolt
32 7 M10 Nylon Locknut
33 2 M10 Nylon Locknut (Bright Zinc)
34 2 M10 Washer (Bright Zinc)
35 8 M10 Washer
36 4 M10 x 25mm Bolt
37 4 M6 x 16mm Screw
38 6 M8 x 42mm Bolt
39 12 M8 Washer
40 4 M8 x 32mm Bolt
41 4 M8 Large Washer
42 2 M10 x 55mm Bolt
43 2 M10 x 75mm Bolt
44 1 M10 x 90mm Bolt
45 2 M10 x 30mm Bolt
46 1 M4 x 20mm Self-tapping Screw
47 1 M6 Nylon Locknut
48 2 M6 x 25mm Screw
49 2 Plastic Knob
# 1 User’s Manual
# 1 Workout Chart
Note: “#” Indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
for information on ordering replacement parts.
PART LIST—Model No. WLEMBE14020 R0604A
WARNING: To reduce the risk of serious injury, read the following important precau-
tions before using the weight training system.
IMPORTANT PRECAUTIONS
1. Read all instructions in this manual before
using the weight training system.
2. It is the responsibility of the owner to ensure
that all users of the weight training system
are adequately informed of all precautions.
3. Use the weight training system only as
described in this manual.
4. Use the weight training system only on a
level surface. Cover the floor beneath the
weight training system to protect the floor.
5. Inspect and properly tighten all parts each
time you use the weight training system.
Replace any worn parts immediately.
6. Keep hands and feet away from moving parts.
7. Always tie back long hair to prevent it from
becoming caught.
8. Keep children under 12 years old and pets
away from the weight training system at all
times.
9. The weight training system should not be
used by persons weighing more than 115 kg
(250 lbs).
10. Always wear athletic shoes for foot protec-
tion whilst exercising.
11. If you feel pain or dizziness whilst exercis-
ing, stop immediately and cool down.
12. The weight training system is intended for
home use only. Do not use the weight train-
ing system in any commercial, rental, or
institutional setting.
13. The decal shown here has been placed on
the weight training system. If the decal is
missing or illegible, call our Customer
Service Department at 08457 089 009 and
order a free replacement decal. Apply the
replacement decal in the location shown.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
Key No. Qty. Description Key No. Qty. Description

4 9
ADJUSTING THE INCLINE
The incline of the weight training system can be adjust-
ed to change the resistance level of your workout.
To adjust the incline, lift the Rail (3) until the knob on
the Adjustment Bracket (9) can be pulled from the
adjustment hole in the Adjustment Leg (8). Raise or
lower the Frame to the desired incline and insert the
knob into an adjustment hole in the Adjustment Leg.
Note: Be sure that the knob on the Adjustment
Bracket is fully inserted into an adjustment hole in
the Adjustment Leg.
SECURING THE CORD
When storing the weight training system, or performing
exercises that do not require the use of the Handles
(not shown), secure the Cord (30) by wrapping it
around the Plastic Knobs (49) on the Stabiliser (4).
ADJUSTMENTS
The weight training system is designed to use your own body weight as resistance. The steps below explain
how the weight training system can be adjusted and folded for storage. Refer to the accompanying exercise
guide to see the correct form for each exercise.
Inspect and tighten all parts each time you use the weight training system. Replace any worn parts immediately.
The weight training system can be cleaned with a damp cloth and mild, non-abrasive detergent; never use
solvents.
9
Knob
8Adjustment
Holes
3
30
4
49
ATTACHING THE HANDLEBAR
For some exercises, the Handlebar (24) must be
attached to the weight training system. Slide the
Handlebar into the Upper Bar (5) and secure it with the
Knob (27). Turn the Knob clockwise until it is tight.
24
27
5
BEFORE YOU BEGIN
Thank you for selecting the WESLO®BODY FLEX
weight training system. The versatile BODY FLEX is
designed to help you develop every major muscle group
of the body. Whether your goal is a shapely figure, dra-
matic muscle size and strength, or a healthier cardiovas-
cular system, the BODY FLEX weight training system
will help you to achieve the specific results you want.
For your benefit, read this manual carefully before
using the WESLO®BODY FLEX weight training sys-
tem. If you have additional questions, please call our
Customer Service Department at 08457 089 009. To
help us assist you, please note the product model num-
ber and serial number before calling. The model num-
ber is WLEMBE14020. The serial number can be found
on a decal attached to the weight training system (see
the front cover of this manual).
Before reading further, please review the drawing
below and familiarise yourself with the parts that are
labelled.
Stabiliser
Rail
Handle
Handgrip
Support Leg
Adjustment Bracket
Adjustment Leg
Adjustment Foot
Seat
CAUTION: Remove the Handlebar
(24) when performing an exercise that does not
require it.

8
6. Remove the Large Pulley (15) from one of the
Pulley Housings (16).
Wrap one end of the Cord (30) around the Large
Pulley (15). Reattach the Large Pulley inside the
Pulley Housing (16) with the M10 x 30mm Bolt (45)
and the M10 Nylon Locknut (32). Note: Do not
overtighten the Bolt; the Pulley should be able
to turn easily.
Repeat this step with the other Pulley Housing (16).
Attach a Handle (28) to each end of the Cord (30)
with the two Clips (29).
7. Make sure all parts are properly tightened before you use the weight training system. The use of the
remaining parts will be explained in ADJUSTMENTS, on page 9.
6
15
16
16
15
32
32
45
45
30
28
28
29
29
5
PART IDENTIFICATION CHART
M10 Nylon Locknut (32, 33)
M10 x 90mm Bolt (44)
M10 x 75mm Bolt (43)
M10 x 55mm Bolt (42)
M10 x 30mm Bolt (45)
M10 x 25mm Bolt (36)
M6 x 138mm Bolt (31)
M8 x 42mm Bolt (38)
M8 x 32mm Bolt (40)
M6 x 25mm Screw (48)
M6 Nylon Locknut (47)
M8 Washer (39)
M4 x 20mm Self-tapping Screw (46)
M8 Large Washer (41)
M6 x 16mm Screw (37)
M8 Nylon Locknut (12)
M10 Washer (34, 35)
This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below
each part refers to the key number of the part, from the PART LIST on page 10. Important: Some parts may
have been pre-assembled for shipping purposes. If you cannot find a part in the parts bags, check to
see if it has been pre-assembled.

Before beginning assembly, carefully read the
following information and instructions:
•Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
•Tighten all parts as you assemble them, unless
instructed to do otherwise.
•As you assemble the weight training system,
make sure all parts are oriented as shown in the
drawings.
•Assembly requires two people.
•For help identifying small parts, use the PART
IDENTIFICATION CHART on page 5.
The following tools (not included) are required
for assembly:
• Two adjustable spanners
• One standard screwdriver
• One Phillips screwdriver
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end span-
ners, or a set of ratchet spanners. If further assis-
tance is needed, please call our Customer
Service Department at 08457-089009.
Make Assembly Easier for Yourself.
Everything in this manual is designed to ensure
that the weight training system can be assem-
bled successfully by anyone. Before beginning
assembly, make sure to read the information
on this page; this brief introduction will save
you much more time than it takes to read it.
6
1. Attach the Stabiliser (4) to the Rail (3) with two M10
x 25mm Bolts (36) and two M10 Washers (35).
2. Attach the Adjustment Foot (7) to the Adjustment
Leg (8) with two M10 x 55mm Bolts (42), four M10
Washers (35), and two M10 Nylon Locknuts (32).
1
ASSEMBLY
7
35
35
2
36
35
35
4
42
8
32
35
35
3
7
3. Note: The following steps require two people.
Attach the Adjustment Leg (8) to the Rail (3) with an
M10 x 90mm Bolt (44) and an M10 Nylon Locknut
(32).
Attach the Support Leg (6) to the Rail (3) with an
M10 x 75mm Bolt (43) and an M10 Nylon Locknut
(32).
Note: Do not overtighten the Locknuts (32); the
Adjustment Leg (8) and the Support Leg (6)
must pivot easily.
4. Have a second person hold the ends of the Cord
(30) above the Seat (1). See the inset drawing.
Slide the Seat Bracket (2) onto the Rail (3). Be sure
that the Wheels (21) are on top of the Rail and
that the Large Bushings (23) are below the Rail.
5. Attach the Upper Bar (5) to the Rail (3) with two
M10 Washers (35) and two M10 x 25mm Bolts (36).
4
5
3
1
30
Decal
3
323
23
21
21 2
3
6
8
43
44
32
36
35
35
3
5
CAUTION: Be sure the Seat (1)
is oriented as shown in the drawing.