Westinghouse WKBE333 User manual

TABLE BLENDER
Instructions
For household use only
¼, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are
trademarks of Westinghouse Electric Corporation, a USA company.
Used under license by Star Glory Limited. All Rights Reserved.
WKBE333 • 07/16
TROUBLESHOOTING
Trouble Solution
No lighting on
button, no function
• Put the jar on the body, plug in
power source.
• Press down the jar again to well start
the safe switch of blender
Lighting on button,
but machine no
function
• Put the jar on the body, plug in
power source.
• Turn the control dial back onto “0”.
Then select the speeds / functions
you need.
Machine stops
after long time
processing
• This is a overload protection to
prevent damage to the motor
• Take off the plug. Cool down the
blender at least 30 mins. and then
plug in again.
Food is not well
processing
• Too much or too large food may be
loaded at one time. Try a smaller
amount, and work in batches if
necessary.
• For best results, ingredients should
be in pieces no larger than 2 cm.
Food sticks to jug
or hard to come
down into blade
working area
• Ingredients may be too large so that
food are jammed by each other. Try
cutting into smaller pieces. For best
results, ingredients should be in
pieces no larger than 2 cm.
• If necessary, set the blender into
min speed and then use the tamper
to press down the food into blade
working area.
• The mixture may be too thick. Try
add more liquid.
Food is Processed
too fine or into
watery
• Try for shorter Processing time.
• Use the PULSE function button for
easy control.
Ice can not well
crushed
• Use smaller size ice (no larger than
2 cm)
• Use the Ice Crush function button
for easy control.
DISPOSAL
Proper disposal of this product.
This label indicates that, in the EU, electronic devices
cannot be disposed of with regular household waste.
Please use the return or collections systems of your
municipality or contact the seller where you purchased this
product.
INFORMATION AND SERVICE
If you have question or concerns about your product,
please visit our website: www.westinghouse-starglory.com,
or contact our oversea ofces/agents.
In line with our policy of continuous product development,
we reserve the right to change product, packaging and
documentation specifications without notice.
5
WKBE333_Table Blender_nIM.indd 1 7/26/2016 5:41:11 PM

Feeder cap
Jar cover
Jar handle
Blade unit
Control dial
Motor unit
Function key
12 3 4
English
INTENDED USE
This device is suitable for ice crushing, blending, pureeing,
and controlled processing only. Any other use may result in
damage to the device or injuries.
IMPORTANT SAFEGUARDS
General
1. Read this manual before rst use thoroughly. It
contains important information for your safety as well
as for the use and maintenance of the equipment. Keep
these instructions for future reference and pass it on
with the device.
2. Pay particular attention to the warnings on the device
and in this instruction manual.
3. Use the device only for its intended purpose. Improper
use may lead to hazards.
4. This device is designed for household use only, not for
staff kitchen areas in shops, offices and other working
environments, farm houses, by clients in hotels, motels
and other residential type environments, bed and
breakfast type environments use. It is not suitable for
commercial use.
5. In the event of improper use or wrong operation, we do
not accept any liability for resulting damages.
6. The use of accessories and components not expressly
recommended by the manufacturer may result in
injuries or damages and voids the warranty.
7. This device is not intended to be used by persons
(including children) with reduced physical, sensory
or mental abilities or lack of experience and / or
lack of knowledge unless they are supervised by a
person responsible for their safety or have received
instructions on how to use the device.
8. Children should be supervised to ensure that they do
not play with the device.
9. Never leave the device unsupervised while it is
switched on.
10. Do not place heavy objects on top of the device.
11. Never immerse electrical parts of the device in water
during cleaning or operation. Never hold the device
under running water.
12. Do not under any circumstances attempt to repair
the device yourself. For servicing and repairs, please
consult an authorised dealer or qualified customer
service centre.
13. This device should not be operated with an external
clock timer or separate remote control system.
Power supply
1. The mains voltage must match the information on the
rating label of the device.
2. The power plug is used as the disconnect device.
Please be sure that the power plug is in operable
condition.
3. Only removing the power plug can separate the device
completely from the mains supply.
4. Avoid damages to the power cord that may be caused
by kinks or contact with sharp corners.
5. Make sure, the device, including power cord and power
plug are not exposed to hot surfaces.
6. Only unplug from the power outlet by the plug itself.
Do not pull on the cord.
7. Disconnect the power plug when the device is not
in use, in case of malfunctions, prior to attaching
accessories and prior to each cleaning.
8. If the power cord or the casing of the device is
damaged or if the device is dropped, the device may
not be used before it is examined by a professional
electrician.
9. A damaged power cord may only be replaced by the
manufacturer or a workshop commissioned by the
manufacturer or by a similarly qualified person in order
to avoid hazards.
Installation location
1. Place the device on a at, sturdy and heat-resistant
surface.
2. Put the device in a place which is out of reach of
children.
3. Do not operate this device near ammable materials
(e.g. curtains, textiles, walls) and never cover it. Ensure
that there is always a sufficient safe distance from
ammable materials.
4. Use this device in dry indoor areas only and never
outdoors.
5. Warning: Do not use this device near water or heavy
moisture; e.g. in a damp basement or beside a
swimming pool or bathtub.
6. In order to reduce the risk of re and electric shock, do
not expose the device to re (replace, grill, candles,
cigarettes and so on) or water (water drops, water
splashes, vases, tubs, ponds and so on).
7. Keep this device away from all heat sources like for
example, ovens, hot plates and other heat-producing
devices/objects.
8. Protect this device from extreme heat (over 35°C) and
cold (under 5°C) as well as from direct sunlight and
dust.
9. Insure clearance above the counter around the
installation to allow for unhampered operation of the
sound reduction cover.
SPECIFIC SAFETY INSTRUCTIONS
1. Only remove accessories from the device after the
motor has come to a complete stop and the plug has
been pulled.
2. Make sure that the motor unit and power cable do not
become wet.
3. Do not operate the device when it is empty in order to
prevent damages.
4. CAUTION: Do not touch any moving parts while the
device is still in operation.
5. CAUTION: Be careful when handling the blade unit. It
has sharp edges.
6. This device may only be used if all original parts are
used together and are not damaged. Do not try to
replace one part with another. If you have to replace a
part, please contact your customer service.
7. Keep hands and utensils out of blender jar while
blending to reduce the risk of severe personal injury
and/or damage to blender.
8. Do not use a broken, chipped or cracked blender jar.
9. Always operate blender with cover in place.
10. The water temperature should not be over 605°C when
cleaning the unit.
11. Do not interfere with the safety switch.
12. Clean the device and other accessories after each use.
Refer to the Chapter CARE AND MAINTENANCE.
Operating time
• Do not use the appliance continuously longer than 3
minutes at a time.
• The in between pauses must be at least 2 minutes.
Safety nursing
• The motor is equipped with protection setting, while
over loading, it will turn off automatically and re-
operate after cooling.
BEFORE FIRST USE
1. Carefully take the device and its accessories out of the
packaging. Retain the packaging in case you would like
to store the device away or transport it at a later date.
If you choose to dispose of the packaging, then please
do so according to the applicable legal regulations.
2. Check the packaging contents for completeness and
damages. Should the contents in the packaging not
be complete or be damaged, do not use the device.
Return it to your retail outlet immediately.
3. Clean the device and other accessories before first use.
Refer to the Chapter CARE AND MAINTENANCE.
USING THE TABLE BENDER
Control dial
• “MODE” CONTROL
Turn the dial to “M” position to select the Pre-set
mode. Mode control buttons (Pulse/Ice crush/
Smoothies) will be illuminated.
• “0” SWITCH CONTROL
This control is to stop the blender or reset the blender
speed.
ATTENTION: The machine will only work when the
switch knob is started from “0” position. Make sure the
mark is at “0” position before or after use.
• “SPEED” CONTROL
Select the speed from 1 to 6 (min. to max.)
Operation:
NOTE: Once plugin, “P” button will be in red light ashing,
it means the machine is ready now.
If the red light is not ashing, please recheck whether the
jar is pressed down well onto the machine body or not.
NORMAL BLENDING
1. Place the Jar onto Blender Motor Base.
2. Put the ingredients into Jar and then cover the lid back
3. Plug into the power source.
4. Make sure the control dial is at “0” position, then
turn the dial to the desire speed (1-6) to start the
processing.
NOTE: The blender only works when the switch knob
is started from “0” position. If blender doesn’t work,
please turn the knob back to “0” position.
5. Ingredients can be added into Jar through feeder cap
in the lid
6. Cut off the power and when motor stop running, take
away the Jar from Blender Motor Base and pour out
the content.
• Example:
Max with 800 g carrot with 1200 mL water, working at
“6” speed for 2 mins. and rest 1 min as 1 cycle. Do not
continue working more than 4 cycles. Cool the motor
for next processing.
PRE-SET MODE:
1. Place the Jar onto Blender Motor Base.
2. Put the ingredients into Jar and then cover the lid back
3. Plug into the power source.
4. Turn the dial to “M” position, the 3 mode buttons will
be illuminated.
5. Press the desire mode button to select between Pulse,
Ice Crush and Smoothies modes.
• “P” Mode – Pulse function
Press and hold for blending, remove to stop.
• “Ice cursh” Mode – Crusher function
Blender under this mode will automatically work: few
seconds on and stop, and repeat the process several
times. Ice crushed under this mode will not spray and
stick onto the jar wall
• “Smoothies” Mode – Smoothies function
Blender under this mode will automatically work: speed
will increase till to max speed, working 2 minutes will
stop by itself.
NOTE: When the blender at “Ice Crush” and
“Smoothies” modes. Only the chosen button will be
illuminated. Press the same button again to cancel the
function and all 3 buttons will be illuminated again.
When using the Pulse function for additional blending.,
the machine will stop at once when your finger is
removed from the button.
6. Cut off the power and when motor stop running, take
away the Jar from Blender Motor Base and pour out
the content.
Using the tamper
1. Take out the Feeder cap from the lid and insert the
Tamper into lid hole.
2. The Tamper is for pushing the food into the blade
blending area .
USING EXTRA DRIVER GEAR SUITS
Product is with 2 extra DRIVER GEAR SUIT in case the
original one is not good after many times heavy duty
usage.
1. Use a tool (such as pliers) to clamp original suit up.
(Pic. A)
2. Press down the new suit. (Pic. B)
3. Make sure the top of new suit is SAME LEVEL as top of
Motor Driver Gear. (Pic, C)
CARE AND MAINTENANCE
WARNING: Do not immerse the motor unit into water or
any liquid.
CAUTION: Never use solvents and abrasives, hard brushes,
metallic or sharp objects for cleaning. Solvents are harmful
to health and attack the plastic parts. Abrasive cleaners
and tools scratch the surface.
1. Do not try to disassemble the blade unit out from the
jar for clean. It will lead to leakage issues.
2. Take the jar out from Blender Motor Base and then
pour / take out the balance food in jar.
ATTENTION: Be careful on the sharp blades.
3. Add a little clean agent with water into jar, and then
use “Smoothies” function to run the jar for 1 cycle.
4. Add pure water into the jar, repeat the operation as
above 2 times.
5. Use a damp cloth to clean the outside of the housing.
6. Allow the parts to dry thoroughly before reassembling
the device.
Tamper
WKBE333_Table Blender_nIM.indd 2 7/26/2016 5:41:11 PM