Whelen Engineering Company Talon Series User manual

Page 1
©2003 Whelen Engineering Company Inc.
Form No.13766D (111703)
Route 145, Winthrop Road,
Chester, Connecticut 06412
Phone: [phone]
Fax: [phone]
Internet: www.whelen.com
Sales e-mail: [e-mail]
Canadian Sales e-mail: [e-mail]
Customer Service e-mail: [e-mail]
Automotive: Beacons
Installation Guide:
Talon Series LED Dash Lights
Safety First
This document provides all the necessary information to allow your Whelen product to be properly and safely installed.
Before beginning the installation and/or operation of your new product, the installation technician and operator must
read this manual completely. Important information is contained herein that could prevent serious injury or damage.
• Proper installation of this product requires the installer to have a good understanding of automotive
electronics, systems and procedures.
• If mounting this product requires drilling holes, the installer MUST be sure that no vehicle components or
other vital parts could be damaged by the drilling process. Check both sides of the mounting surface
before drilling begins. Also de-burr the holes and remove any metal shards or remnants. Install grommets
into all wire passage holes.
• If this product is mounted with tape or Velcro™, clean the mounting surface with a 50/50 mix of isopropyl
alcohol and water and dry thoroughly.
• Do not install this product or route any wires in the deployment area of your air bag. Equipment mounted
or located in the air bag deployment area will damage or reduce the effectiveness of the air bag, or
become a projectile that could cause serious personal injury or death. Refer to your vehicle owners
manual for the air bag deployment area. The User/Installer assumes full responsibility to determine proper
mounting location, based on providing ultimate safety to all passengers inside the vehicle.
• For this product to operate at optimum efficiency, a good electrical connection to chassis ground must be
made. The recommended procedure requires the product ground wire to be connected directly to the
NEGATIVE (-) battery post (this does not include products that use cigar power cords).
• If this product uses a remote device for activation or control, make sure that this device is located in an
area that allows both the vehicle and the device to be operated safely in any driving condition.
• Do not attempt to activate or control this device in a hazardous driving situation.
• This product contains either strobe light(s), halogen light(s), high-intensity LEDs or a combination of
these lights. Do not stare directly into these lights. Momentary blindness and/or eye damage could result.
• Use only soap and water to clean the outer lens. Use of other chemicals could result in premature lens
cracking (crazing) and discoloration. Lenses in this condition have significantly reduced effectiveness
and should be replaced immediately. Inspect and operate this product regularly to confirm its proper
operation and mounting condition. Do not use a pressure washer to clean this product.
• It is recommended that these instructions be stored in a safe place and referred to when performing
maintenance and/or reinstallation of this product.
• FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS AND INSTRUCTIONS COULD RESULT IN DAMAGE
TO THE PRODUCT OR VEHICLE AND/OR SERIOUS INJURY TO YOU AND YOUR PASSENGERS!
®
ENGINEERING COMPANY INC.

Page 2
Dash Light can be
mounted two ways
for optional deck
mounting.
Mounting (All Talons)...
CAUTION! Nighttime operation of this product may produce
reflected light within the vehicle! Use with caution!
The Talon includes a complete suction cup mounting kit (see your
Whelen dealer for information on other optional mounting
brackets). Refer to the parts diagrams for hardware illustration.
1. Secure the lower
mounting bracket to the
Talon (the Dual Talon
uses two brackets).
2. Slide the suction cups
onto the upper mounting
bracket and secure the
upper mounting bracket
onto the lower mounting
bracket.
3. Attach the reflector tape
to the visor hood. Then
secure the visor hood to
the unit.
4. Apply the suction cups to
the windshield. Do not
locate the Talon in any
location where it will interfere with the drivers ability to
safely operate the vehicle. Refer to the safety warnings
on the cover of this manual.
5. Adjust the angle of the Talon so that the visor hood is in full
contact with the windshield.
There are holes on the upper bracket to be used if permanent
mounting is desired. Using the upper bracket as a template, mark
the areas where the mounting holes are to be drilled. Secure the
unit using the appropriate hardware (customer supplied).
Wiring...
NOTE: Standard Talons use a cigar cord for power
connection and no further wiring is necessary. Sync Talons
are required to be wired as outlined below.
One Sync Talon (single or double)
1. Extend the RED wire to a Single Pole/Single Throw switch.
From this switch, extend a wire to +12VDC. Fuse this wire @
3 Amps.
All customer supplied wires that connect to the Positive (+)
battery terminal must be sized to supply at least 125% of the
maximum operating current and fused “at the battery” to
carry that load.
2. Extend the BLACK wire to chassis ground.
3. The GREY wire is not used. Cut & cap this wire.
Flash Pattern Selection:
To advance to the next flash pattern, press the pattern selection button
for less than 1 second.
To cycle backwards to previous patterns, press the pattern selection
button for more than 1 second.
To reset to the factory default pattern, begin by turning off power to the
lighthead. While pressing the pattern selection button, turn the lighthead
back on. and keep the pattern selection button depressed for more than 5
seconds.
Flash patterns for the Talon are listed on the following 2 pages.
Two (or more) Sync Talons (single or double)
1. Extend the RED wire from one Talon to a Single Pole/Single
Throw switch. From this switch, extend a wire to +12VDC.
Fuse this wire @ 3 Amps. Repeat for the remaining Talon
2. Extend the BLACK wires from each Talon to chassis ground.
3. Butt splice the two GREY wires together.
Synchronizing Single Talons - To sync two or more lightheads,
configure all lightheads to display the same Phase 1 pattern.
When the lightheads are activated, the patterns displayed will be
synchronized. To configure specific lightheads to alternate their
patterns with other lightheads, advance the pattern of the desired
lighthead(s) to the Phase 2 mode of the current pattern (see Sync
pattern table for pattern list).
Synchronizing Dual Talons - The dual Talon has 4 unique
modes for each of the 5 available patterns; Alternating Phase 1,
Alternating Phase 2, Simultaneous Phase 1 and Simultaneous
Phase 2. In Alternating mode, the left lighthead in a dual Talon
alternates with the right lighthead. In Simultaneous mode, the left
and right lighthead in a dual Talon flash simultaneously.
The diagram below shows the relationship between two, dual
synchronized Talons. Keep in mind that all Talons connected by
the Grey wire must be configured to flash the same pattern (as
shown, both Talons are displaying Signal Alert).
Signal Alert Phase 1 (alt.)
Signal Alert Phase 1 (alt.)
Signal Alert Phase 1 (alt.)
Signal Alert Phase 2 (alt.)
Signal Alert Phase 1 (sim.)
Signal Alert Phase 1 (sim.)
Signal Alert Phase 1 (sim.)
Signal Alert Phase 2 (sim.)
RED: +12VDC
GREY: SYNC (Not Used)
BLACK: Ground
(+)
Battery
(-)
Pattern Selection Button
Single TALON shown for reference
SPST switch
(customer supplied)
3 AMP fuse
(customer supplied)
Cut & cap GREY wire
RED: +12VDC
GREY: SYNC
BLACK: Ground
RED: +12VDC
GREY: SYNC
BLACK: Ground
(+) (-)
Pattern Selection ButtonPattern Selection Button
Butt Splice
BATTERY
Single TALON shown for reference
SPST switch
(customer supplied) SPST switch
(customer supplied)
3 AMP fuse
(customer supplied)

Page 3
Single Talon Flash Patterns
Standard Sync
Signal Alert 75
Signal Alert 150
Single Flash 375
Single Flash 150
Single Flash 75
Single Flash 15
Double Flash 150
Double Flash 75
Comet Flash 75
Action Flash
Modu Flash
Com Alert
Action Scan
Signal Alert Steady
Steady
Signal Alert (Phase 1)
Signal Alert (Phase 2)
Comet Flash (Phase 1)
Comet Flash (Phase 2)
Double Flash (Phase 1)
Double Flash (Phase 2)
Single Flash (Phase 1)
Single Flash (Phase 2)
Com Alert (Phase 1)
Com Alert (Phase 2)
3
2
8a 8b
9
45
67
3
2
1
1
11 12 1310
TALON LED DASH LIGHT (SINGLE)
01-0685926- _ S TALON SINGLE LED DASH LIGHT
01-0485926-00
1KIT INSTALLATION DASH LIGHT/
SCREW 6 X 1/2 PPH PLASTI-LOK SS BLACK OXIDE/
15-06521B-080
2
11-463555-000
2HOUSING SINGLE LED DASH LIGHT/
01-0269508-10
A/R SUB ASSY. LINEAR LED DASH LIGHT AMBER/
A/R
A/R
A/R
02-0169576-00
02-0169486-00
A/R
A/R
PCB ASSY / SINGLE TALON (SYNC)
PCB ASSY / SINGLE TALON (STANDARD)
21-31000512-0
1PLUG HOLE RUBBER 5/32 DIA/
01-0269508-20 SUB ASSY. LINEAR LED DASH LIGHT BLUE/
01-0269508-30 SUB ASSY. LINEAR LED DASH LIGHT WHITE/
01-0269508-50 SUB ASSY. LINEAR LED DASH LIGHT RED/
68-3963604-10 LENS AMBER SNAP-ON LED DASH LIGHT/
A/R 68-3963604-20
A/R
LENS BLUE SNAP-ON LED DASH LIGHT/
68-3963604-30
1LENS CLEAR SNAP-ON LED DASH LIGHT/
68-3963604-50
A/R LENS / RED SNAP-ON LED DASH LIGHT
2
3
ITEM PART NUMBER DESCRIPTION
QTY
11
12
13
4
5
6
7
8a
8b
9
10
1
= RED LED / CLEAR LENS
LED-LENS COLOR
01-0685926-50 LED-LENS COLOR
A=
B=
W=
R=
AMBER/AMBER
BLUE/BLUE
WHITE/CLEAR
RED/RED
LED-LENS COLOR
1=
2=
5=
AMBER/CLEAR
BLUE/CLEAR
RED/CLEAR
NOTE:
The Standard Talon uses
a cigar cord as shown here.
Ribbed
(-)
Smooth
(+)
On/Off
Switch
Cigar Cord with
on/off switch &
internal 8A fuse

Page 4
Standard Sync
Dual Talon Flash Patterns
Signal Alert (Alt. / Phase 1)
Signal Alert (Alt. / Phase 2)
Comet Flash (Alt. / Phase 1)
Comet Flash (Alt. / Phase 2)
Double Flash (Alt. / Phase 1)
Double Flash (Alt. / Phase 2)
Single Flash (Alt. / Phase 1)
Single Flash (Alt. / Phase 2)
Com Alert (Sim. / Phase 1)
Com Alert (Sim. / Phase 2)
Signal Alert (Sim. / Phase 1)
Signal Alert (Sim. / Phase 2)
Comet Flash (Sim. / Phase 1)
Comet Flash (Sim. / Phase 2)
Double Flash (Sim. / Phase 1)
Double Flash (Sim. / Phase 2)
Single Flash (Sim. / Phase 1)
Single Flash (Sim. / Phase 2)
Com Alert (Alt. / Phase 1)
Com Alert (Alt. / Phase 2)
Rapid Fire 680
Rapid Fire 240
Rapid Fire 120
Simultaneous Rapid Fire 150
Double Flash 240
Double Flash 120
Simultaneous Double Flash 150
Comet Flash
Simultaneous Comet Flash
Action Flash
Simultaneous Action Flash
ModuFlash
Simultaneous ModuFlash
Signal Alert 120
Simultaneous Signal Alert 80
Scan Flash
Cal. Flash
Cal Steady w/Rapid Fire
Cal. Steady w/Cal. Flash
Cal. Steady w/Comet Flash 120
Cal. Steady w/Action Flash
8a 8b
9
2
45
3
2
3
67
NOTE:
The Standard Talon uses
a cigar cord as shown here.
= RED LED / CLEAR LENS
LED-LENS COLOR
01-0685926-50 LED-LENS COLOR
A=
B=
W=
R=
AMBER/AMBER
BLUE/BLUE
WHITE/CLEAR
RED/RED
LED-LENS COLOR
1=
2=
5=
AMBER/CLEAR
BLUE/CLEAR
RED/CLEAR
TALON LED DASH LIGHT (DUAL)
01-0685925S_ _
01-0485925-00
15-06521B-080
11-483849-000
01-0269508-10
02-0169484-00
02-0169608-00
21-31000512-0
01-0269508-20
01-0269508-30
01-0269508-50
68-3963604-10
68-3963604-20
68-3963604-30
68-3963604-50
1
3
2
A/R
A/R
A/R
A/R
1
1
1
A/R
A/R
2
A/R
1
2
3
4
5
6
7
8a
8b
9
10
11
12
13
TALON DUAL LED DASH LIGHT
KIT INSTALLATION DASH LIGHT/
SCREW 6 X 1/2 PPH PLASTI-LOK SS BLACK OXIDE/
HOUSING DUAL LED DASH LIGHT/
SUB ASSY. LINEAR LED DASH LIGHT AMBER//
PCB ASSY / DUAL TALON (SYNC)
PCB ASSY / DUAL TALON (STANDARD)
PLUG HOLE RUBBER 5/32 DIA/
SUB ASSY. LINEAR LED DASH LIGHT BLUE//
SUB ASSY. LINEAR LED DASH LIGHT WHITE//
SUB ASSY. LINEAR LED DASH LIGHT RED//
LENS AMBER SNAP-ON LED DASH LIGHT/
LENS BLUE SNAP-ON LED DASH LIGHT/
LENS CLEAR SNAP-ON LED DASH LIGHT/
LENS / RED SNAP-ON LED DASH LIGHT
ITEM PART NUMBER DESCRIPTION
QTY
1
1
Ribbed
(-)
Smooth
(+)
On/Off
Switch
Cigar Cord with
on/off switch &
internal 8A fuse
11
12 13
10