Whelen Engineering Company 900 Series User manual

Page 1
®
ENGINEERING COMPANY INC.
Route 145, Winthrop Road,
Chester, Connecticut 06412
Phone: [phone]
Fax: [phone]
Internet: www.whelen.com
Sales e-mail: [e-mail]
Canadian Sales e-mail: [e-mail]
Customer Service e-mail: [e-mail]
Automotive: Lightheads
Installation Guide: 900 Series Lighthead
Halogen, Brake-Tail-Turn & Strobe
©2001 Whelen Engineering Company Inc.
Form No.13627J (032207)
Safety First
This document provides all the necessary information to allow your Whelen product to be properly and safely installed.
Before beginning the installation and/or operation of your new product, the installation technician and operator must
read this manual completely. Important information is contained herein that could prevent serious injury or damage.
• Proper installation of this product requires the installer to have a good understanding of automotive electronics,
systems and procedures.
• If mounting this product requires drilling holes, the installer MUST be sure that no vehicle components or other
vital parts could be damaged by the drilling process. Check both sides of the mounting surface before drilling
begins. Also de-burr any holes and remove any metal shards or remnants. Install grommets into all wire
passage holes.
• If this manual states that this product may be mounted with tape or Velcro™, clean the mounting surface with a
50/50 mix of isopropyl alcohol and water and dry thoroughly.
• Do not install this product or route any wires in the deployment area of your air bag. Equipment mounted or
located in the air bag deployment area will damage or reduce the effectiveness of the air bag, or become a
projectile that could cause serious personal injury or death. Refer to your vehicle owners manual for the air bag
deployment area. The User/Installer assumes full responsibility to determine proper mounting location, based
on providing ultimate safety to all passengers inside the vehicle.
• For this product to operate at optimum efficiency, a good electrical connection to chassis ground must be
made. The recommended procedure requires the product ground wire to be connected directly to the NEGATIVE
(-) battery post.
• If this product uses a remote device to activate or control this product, make sure that this control is located in
an area that allows both the vehicle and the control to be operated safely in any driving condition.
• Do not attempt to activate or control this device in a hazardous driving situation.
• This product contains either strobe light(s), halogen light(s), high-intensity LEDs or a combination of these
lights. Do not stare directly into these lights. Momentary blindness and/or eye damage could result.
• Use only soap and water to clean the outer lens. Use of other chemicals could result in premature lens cracking
(crazing) and discoloration. Lenses in this condition have significantly reduced effectiveness and should be
replaced immediately. Inspect and operate this product regularly to confirm its proper operation and mounting
condition. Do not use a pressure washer to clean this product.
• It is recommended that these instructions be stored in a safe place and referred to when performing
maintenance and/or reinstallation of this product.
• FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS AND INSTRUCTIONS COULD RESULT IN DAMAGE TO
THE PRODUCT OR VEHICLE AND/OR SERIOUS INJURY TO YOU AND YOUR PASSENGERS!
For warranty information regarding this product, visit www.whelen.com/warranty

Page 2
STYLE
1- WARNING
2
3
4
5
6
- SCENE
-B/T/T
- STROBE
- BACK-UP
- SCENE / 24V
COLOR / LENS TYPE
R- RED
B
G
A
C
- BLUE
- GREEN
- AMBER
- CLEAR
CABLE:
0
1
- AMP no CABLE
- AMP with CABLE
2- DEUTSCH no CABLE
3- DEUTSCH with CABLE
STYLE
PART NUMBER KEY:
BASIC P/N CABLECOLOR
01-0683694___
20
16
21
18
31
1
23 4 5 6
8 9 10 11 12 13
IMPORTANT NOTE: Only use replacement
bulbs of the same specifications.
17
- AMBER ARROW
- GRADIENT SCENE
T
Z
NOTE: Halogen cable shown for reference only and is not included.
28
25
19
B
15
C D
This list includes 900 Series Replacement
Parts Exclusive to Lightheads using the
Any lenses, gaskets,
mounting hardware for
this reflector are listed below.
Max Beam Reflector.
wire harneses or
DIRECTIONAL MAX BEAM REFLECTOR W/ SEAL
C
STOP-TAIL-TURN LAMP #1157
34-0021562-00
1
133-0042829-00
LAMPHOLDER ASSY BAYONET WARNING- AMP / TWIST-IN
B
01-0683692-( )
900 SERIES FINAL ASSY. / AMP
168-5981389-08
A
LAMPHOLDER ASSY BAYONET WARNING- DEUTSCH / TWIST-IN
33-0042829-01
D
1
1
1
900 SERIES FINAL ASSY. / DEUTSCH 01-0683692-( )
PART NUMBER DISCRIPTION
QTY ITEM QTY
AMAX-BEAM
REFLECTOR
MAX-BEAM
REFLECTOR
MAX-BEAM
REFLECTOR
5
*
Y
X
Q
- KKKE RED
- SPLIT
- 13 SCENE
- 26 SCENE
- RED ARROW
º
º
CABLE
0
1
- AMP without CABLE
- AMP with CABLE
- DEUTSCH without CABLE
- DEUTSCH with CABLE
2
3
COLOR
PART NUMBER KEY:
BASIC P/N CABLE REQ.
01-0683692-__
COLOR
R
A
Q
T
- RED
- AMBER
- RED ARROW
- AMBER ARROW
900 Series Lighthead / Replacement Parts
30 32
33
7
26 27
22 23
A/R
A/R
1
4
A/R
1
1
A/R
900 SERIES BACK-UP/
QTY QTY
REFLECTOR 900 STROBE WATERPROOF//
A/R A/R 27
A/R 26
A/R 25
REFLECTOR 900 STROBE METAL with SEAL/// A/R
900 SERIES STROBE/
1
A/R
A/R
A/R
A/R
A/R
A/R
A/R
A/R
4
PART NUMBERITEMQTY DESCRIPTION
#8 X 1 1/2" PHILLIPS PAN HEAD SMS
GASKET
12
1
10
1
CABLE ASSEMBLY
9
A/R
8
7
1
4
LENS RED/
6
A/R
LENS GREEN/
5
A/R
LENS CLEAR/
4
A/R
LENS BLUE/
3
A/R
LENS AMBER/
2
A/R
900 SERIES WARNING LIGHT/
1
15
SNAP-IN LAMP 12V-35H/
SNAP-IN LAMP 12V-60W/
LENS KKKE-SPEC RED//
REFLECTOR / 900 HALOGEN / /
METAL with SEAL
LENS ASSEMBLY SCENELIGHT 26/
LENS ASSEMBLY SCENELIGHT 13/
ARROW LENS AMBER with PAINT LEFT HAND//
ARROW LENS RED with PAINT LEFT HAND//
DUAL FILAMENT LAMP 27W-12W/
LENS ASSY 900 SERIES HALOGEN SPLIT/
QTYQTY
11
13
18
17
16
23
22
21
20
19
A/R
A/R
A/R
900 SERIES SCENE 12V//
900 SERIES / BRAKE-TAIL-TURN
44
A/R
A/R
A/R
A/R
A/R
1
1
1
1
A/RA/R
1
1
A/R
A/R
A/R A/R A/R A/R 28 CABLE ASSY. DEUTSCH/
QTY
900 SERIES SCENE 24V//
4
A/R
A/R
A/R
1
1
A/R
A/R
A/R
QTY
900 SERIES GRADIENT SCENE 12-24V//
4
A/R
A/R
1
1
A/R
A/R
30
SNAP-IN LAMP 12V-27H/
1
4444 31 4
GROMMET
4
132
SNAP-IN LAMP / 28V-35W
4
A/R
SNAP-IN LAMP / 12V-50H
02-0283694-00C
33
A/R
1
01-06836945C___
02-0383678-01
02-0383678-00
01-06836944___
38-0481690-00
68-5983540-02
01-0440624-15
15-081416-240
68-1183542-10
34-0041987-00
34-0041987-07
68-1183542-20
68-1183542-30
68-1183542-40
68-1183542-50
68-1183542E50
02-0361457-26
02-0361457-13
68-1181745L1P
68-1181745L5P
34-0062389-00
02-0363407-**
01-06836943___
01-06836942___
01-06836941___
01-0442199-15
01-06836946___
01-0683694_Z_
34-0041987-03
21-1708080603
34-0041987-02
34-0041987-01
68-1983892-30
LENS GRADIENT SCENE CLEAR//
NOTE: Tie the ring
terminals to the
chassis ground.
(STROBE ONLY)
02-0283694-01C
02-0283694-02C
02-0283694-03C
SUB ASS'Y, 900 REFLECTOR 2 WIRE/3 POS AMP
SUB ASS'Y, 900 REFLECTOR 3 WIRE/3 POS AMP
SUB ASS'Y, 900 REFLECTOR 2 WIRE/3 POS DEUTSCH
SUB ASS'Y, 900 REFLECTOR 3 WIRE/3 POS DEUTSCH
Mounting:
1. Using the mounting diagram on the next page,
mark off the mounting holes and the “cut-out” area.
2. Using a .250 drill bit, drill the mounting holes then
carefully cut and remove the area of the mounting
surface as shown. Do not remove the mounting
surface where the mounting holes are drilled.
3. Insert supplied grommets into the mounting holes.
4. Route the cable through the wiring hole to the
power supply. (For strobe, be sure that both ring
terminals are grounded to the vehicle chassis.)
Plug the cable into the power supply and test the
operation of the lighthead, then position the
Lighthead components onto the mounting surface
and secure them to the vehicle using the four #8 x
1½” sheet metal screws. NOTE: When mounting a
“gradient” scenelight lens (Item 13), the word
“TOP” imprinted on the lens must be located on
top of the lens when mounted.
WARNING! The strobe light power supply is a high
voltage device. Do not remove strobe
tubes or dismantle strobe lightheads in
system while in operation. Wait 10 minutes
after turning off power before working or
troubleshooting.
WARNING! All customer supplied wires that connect
to the positive (+) terminal of the battery,
must be sized to supply at least 125% of
the maximum operating current, and fused
“at the battery” to carry that load.

Page 3
900 SERIES LIGHTHEAD MOUNTING DIAGRAM
NOTE: The dimensions shown in this illustration are shown to the third decimal place. Although the tools capable of cutting this
opening are not usually this accurate, it is absolutely necessary to try and stay as close to these dimensions as possible.
This diagram is not to scale. Before drilling, confirm all dimensions.IMPORTANT:
3.081
3.416
6.831
6.162
2.625
5.250
3.224
6.447
3.625
4.349
7.250
8.698
3.552
1.776
5.012
2.506
CUT-OUT AND REMOVE
THIS AREA
CUT-OUT AND REMOVE
THIS AREA
CUT-OUT AND REMOVE
THIS AREA
.250 (1/4")
MOUNTING
HOLE
.250 (1/4")
MOUNTING
HOLE
.250 (1/4")
MOUNTING
HOLE
.250 (1/4")
MOUNTING
HOLE
8.40"
FLANGE KIT / 900 SERIES
PART NUMBER DESCRIPTIONITEMQTY
FLANGE GASKET
38-0481440-00
11
FLANGE KIT SEALwith 01-0462945-01
*
21
11-783130-002
FLANGE with SEAL
11.28
2
1
OVERALL
FLANGE
DIMENSIONS
(Including Flange Gasket)