Whispbar K417W Operation and installation manual

K417W
Fitting Kit
EN Fitting Instructions for Basic Carrier
DMontageanleitung für Basisträgersystem
ES Instrucciones de montaje para el sistema de transporte.
FInstructions de montage pour Basic Carrier
NO Monteringsanvisning for takstativ
PT Instruções de Montagem para sistema de transporte.
RU Установочные Инструкции для Поперечных Балок
x 4 x 2
Revision No: 4C 1

Fitting Kit K417W
MAX kgs (lbs)
W/P WHD
Fiat
Punto , 5dr Hatch 99-03 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Punto , 5dr Hatch 99-03 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Punto , 5dr Hatch 99-03 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Punto , 5dr Hatch 99-03 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Punto , 5dr Hatch 99-03 ZA 50 kgs (110 lbs) 50 kgs (110 lbs)
Punto , 5dr Hatch 99-03 ZA 50 kgs (110 lbs) 50 kgs (110 lbs)
Punto , 5dr Hatch 99-03 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Punto , 5dr Hatch 99-03 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
2

Fitting Kit EN
K417W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3

Fitting Kit EN
K417W
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment.
●Ensure each end of the crossbar is
adjusted equally.
4

Fitting Kit EN
K417W
●Remove locking screw.
●Cut grey protective strip in two equal
lengths.
●Apply protective strip as shown.
Trim if required.
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
5

Fitting Kit EN
K417W
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Fit rubber pad (supplied with crossbar) to
foot.
●Make sure the pad fits into the holes
underneath the foot.
6

Fitting Kit EN
K417W
Fitment
●Pull back rubber seal to expose fixed points
on vehicle body.
●Locate vehicle's fixed points.
●Attaches to factory-fitted mounting points
located between rubber seals on door
frame
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Please check the rear of this manual for
information relating specifically to your
vehicle.
7

Fitting Kit EN
K417W
●Slide clamp into the fixed point ensuring
that it is fully engaged.
●When viewed from the top, clamp should
be lined up with the two lugs on both sides.
●Repeat for all four positions.
8

Fitting Kit EN
K417W
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
9

Fitting Kit EN
K417W
●Please take care when closing the doors as
contact can be made with the clamp if it is
not installed correctly. Close the door
slowly upon first inspection.
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10