Whitewood Furniture TV-63 User manual

ITEM NO.: TV-63
REVISED AUG 01, 2015
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: 2 DOOR ENTERTAINMENT CENTER
: TV-63

ITEM NO.: TV-63
REVISED AUG 01, 2015
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to beginning
assembly, however, make sure all parts and hardware are included and free of obvious defect. If a part is
missing or defective, please contact the store where purchased. If hardware is missing, or you need help with
assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from
being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish of your
product. Protect the surface of the product with cloth if you are using any product with rubber feet or
base.
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO Description Qty Sketch NO Description Qty Sketch
A Server box 1 B Leg
(L-R) 4
C Bottom shelf 1
D
Side
Adjustable
shelf
2
E
Center
Adjustable
shelf
2
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: TV-63
REVISED AUG 01, 2015
Printed in Vietnam
- 3 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
STEP 1
Attach legs (B) to the server (A) with bolts (1), and washers (2) and (3) as shown below. Tighten with
Allen key (7).
Attach L-brackets (6) to legs (B) with screws (8). Tighten with a screwdriver
Place shelf (C) on L-brackets (6) and attach with screws (8) as shown below. Tighten with a
screwdriver.
NO Description Qty Sketch NO Description Qty Sketch
1 Bolt
(M6 x 60mm) 8
7 Allen key
(4x80mm) 1
2 Spring washer
(6.5x11mm) 8
8 Short screw
(M3.5x15mm) 26
3 Flat washer
(6.5x19mm) 8
9 Shelf support
bracket
16
4 Metal knob
(F32x30mm) 2
10 Steel band
1
5 Pan head screw
(M4 x 20mm) 2
11 Long screw
(M4x30mm) 1
6 L-bracket 4
12 Warning label 2

ITEM NO.: TV-63
REVISED AUG 01, 2015
Printed in Vietnam
- 4 -
STEP 2
Attach knobs (4) to front of doors with screws (5) as shown below. Tighten with a screwdriver.
STEP 3
Stick the warning labels (12) at back side of doors before use.
Attach steel band (10) to the unit with screws (8) as shown below. Tighten with the screwdriver.
Attach the steel band to the wall with screws (11) to secure the product and prevent tipping.
Attach brackets (9) to the unit with screws (8) as shown below. Tighten with the screwdriver.
Put the shelves (D) and shelves (E) on brackets (9).