Whitewood Furniture BD-8005 User manual

ITEM NO: BD-8005
REVISED APR 07, 2015
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
:5DRAWERCHESTRTA
: BD-8005

ITEM NO: BD-8005
REVISED APR 07, 2015
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish
of your product. Protect the surface of the product with cloth if you are using any product
with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO: BD-8005
REVISED APR 07, 2015
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO Description Qty Sketch NO Description Qty Sketch
A Top
1
B
Side panel 2 (L-
R)
C Bottom panel
1
D
Center panel 1
E Back rail
2
F
Back panel 3
G
Drawer front
5
H
Drawer side 10
(L-R)
I Drawer back
5
J
Drawer bottom 5
K Support bar
5

ITEM NO: BD-8005
REVISED APR 07, 2015
Printed in Vietnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO Description Qty Sketch NO Description Qty Sketch
1 Allen key
(M4x80mm) 1
2 Bolt
(M6 X 30mm) 12
3 Spring washer
(6.5x11mm) 12
4 Flat Washer
(6.5x13mm) 12
5 Screw
(M4 X 35mm) 65
6
Pan head
screw
(M4 x 30mm)
10
7
Knob
(30x30mm) 10
8 Screw
(M4 X 30mm) 10
9 Steel band 1
10 Warning label 5
11 Screw
(M3 X 15mm) 2

ITEM NO: BD-8005
REVISED APR 07, 2015
Printed in Vietnam
- 5 -
STEP 1
Attach top (A), center panel (D), and bottom panel (C) to a side panel (B) with bolts (2) and washers
(3) and (4) .Tighten with Allen key (1).
Slide back panel (F), and back rail (E) into the groove as shown below.
STEP 2
Attach bottom panel (C), center panel (D), and top (A) to the other side panel (B) with bolts (2), and
washers (3) and (4) .Tighten with Allen key (1).

ITEM NO: BD-8005
REVISED APR 07, 2015
Printed in Vietnam
- 6 -
STEP 3
Attach back rail (E) to side panels (B) with screws (5) .Tighten with a screwdriver.
Attach the steel band (9) to Chest with screws (11) as shown below.
STEP 4
Attach drawer sides (H) to drawer front (G) with screws (5). Tighten with a screwdriver
Insert drawer bottom (J) into the grooves at bottom of drawer sides (H), and drawer front (G) as shown
below.

ITEM NO: BD-8005
REVISED APR 07, 2015
Printed in Vietnam
- 7 -
STEP 5
Attach drawer back (I) to drawer sides (H) with screws (5) as shown below. Tighten with a screwdriver.
STEP 6
Attach support bars (K) to bottom of drawers with screws (8) as shown below. Tighten with the
screwdriver.

ITEM NO: BD-8005
REVISED APR 07, 2015
Printed in Vietnam
- 8 -
Attach knobs (7) to front of drawers with screws (6). Tighten with the screwdriver.
Stick the warning labels (10) inside the drawers before use
Attach the steel band (9) to the wall with screws (5) as shown below (to secure the product and
prevent tipping).
STEP 7
STEP 8