Whitewood Furniture H-4 User manual

ITEM NO.: H-4
REVISED DEC 29, 2015
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: HUTCH W/4 DOORS
: H-4

ITEM NO.: H-4
REVISED DEC 29, 2015
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: H-4
REVISED DEC 29, 2015
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Crown
1
B
Front frame
with doors
1
C
Base frame
1
D
Back rail
1
E
Side panel
(L&R)
2
F
Adjustable
frame
2
G
Bottom
shelf
1
H
Top back
panel
2
I
Bottom
back panel
1
J
Vertical rail
1
K
Glass (Shelf)
2
L
Glass (Door)
4
M
Light
(light-
connector)
2

ITEM NO.: H-4
REVISED DEC 29, 2015
Printed in Vietnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Short bolt
( M6x35mm)
4
2
Long Pan head
screw
(M4 x 30mm)
4
3
Short screw
( M3.5x15mm)
30
4
Medium screw
(M4 x 30mm)
18
5
L-Bracket
3
6
Bracket
8
7
Short Pan head
Screw
(M5 x 20mm)
6
8
Flat Washer
(ɸ6.5x13mm)
4
9
Lock Washer
(ɸ6.5x11mm)
4
10
Metal plate
2
11
Steel band
2
12
Allen key
(M4X80mm)
1
13
Knob
4
14
Long bolt
( M6x45mm)
2
15
Long screw
(M4 x 40mm)
4

ITEM NO.: H-4
REVISED DEC 29, 2015
Printed in Vietnam
- 5 -
STEP 1
Attach Lights (M) to Crown (A) with screws (3). Tighten with a screwdriver.
STEP 2
Attach glass sections (L) to back of front frame with doors (B), and lock it.
Attach knobs (13) to doors with pan head screws (2) as shown below. Tighten with a screwdriver.

ITEM NO.: H-4
REVISED DEC 29, 2015
Printed in Vietnam
- 6 -
STEP 3
Attach Back rail (D), Bottom shelf (G), and Vertical rail (J) with Bolts (14). Tighten with Allen key (12).
Then slide Top back panels (H) into groove as shown below.
STEP 4
Attach side panels (E) to back rail (D) with pan head screws (7) as shown below. Tighten with a
screwdriver.
Attach side panels (E) to bottom shelf (G) with bolts (1), and washers (8) and (9) as shown below.
Tighten with Allen key (12).

ITEM NO.: H-4
REVISED DEC 29, 2015
Printed in Vietnam
- 7 -
STEP 5
Attach front frame with doors (B) to unit with pan head screws (7) as shown below. Tighten with a
screwdriver.
ST
STEP 6
Attach L-brackets (5) with screws (3) as shown below. Tighten with a screwdriver.

ITEM NO.: H-4
REVISED DEC 29, 2015
Printed in Vietnam
- 8 -
STEP 7
Slide bottom back panel (I) into grooves as shown below.
STEP 8
Attach base frame (C) to unit with screws (4) as shown below. Tighten with a screwdriver.

ITEM NO.: H-4
REVISED DEC 29, 2015
Printed in Vietnam
- 9 -
STEP 9
Insert brackets (6) into the unit. Place the frame (F) on the brackets and attach with screws (3).
Tighten with a screwdriver.
Place glass shelves (K) on the frame (F) as shown below.
STEP 10
Attach crown (A) to the unit with screws (4) as shown below. Tighten with a screwdriver.

ITEM NO.: H-4
REVISED DEC 29, 2015
Printed in Vietnam
- 10 -
STEP 11
Attach connectors (M) to the unit with screws (15), as shown below. Tighten with a screwdriver.
Attach metal plate (10) to unit with screws (3) as shown below. Attach metal plate (10) to Buffet or
Server (to secure the product and prevent tipping). Tighten with a screwdriver.
Attach steel band (11) to unit with screws (3) and attach steel band (11) to the wall with screws (4)
as shown below (to secure the product and prevent tipping). Tighten with a screwdriver.