Whitewood Furniture TV-34 User manual

ITEM NO.: TV-34
REVISED APR 03, 2020
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
WARNING!
Serious or fatal injuries can occur from furniture tip over. Use tip over restraint
(provided) to secure this product to the wall.
Description
Item No
: 48 IN TV STAND
: TV-34

ITEM NO.: TV-34
REVISED APR 03, 2020
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: TV-34
REVISED APR 03, 2020
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
G
Vertical Panel
(L-R)
2
B
Bottom Panel
1
H
Side Shelf
2
C
Center Shelf
2
I
Center Back
panel (L-R)
2
D
Door (L-R)
2
J
Side Back
panel
2
E
Glass
2
K
H - Connector
1
F
Side Panel
(L-R)
2

ITEM NO.: TV-34
REVISED APR 03, 2020
Printed in Vietnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Bolt
(M6 x 35mm)
16
9
Short Pan head
screw
(M3 x 15mm)
4
2
Spring Washer
(6.5 x 11mm)
16
10
Short Pan head
screw
(M3.5 x 15mm)
10
3
Flat Washer
(6.5 x 19mm)
16
11
Long Screw
(M4 x 25mm)
2
4
Allen key
(M4 x 30mm x 110mm)
1
12
Shelf support
bracket
16
5
Medium Pan head
screw
*Metal knob: (M4x22mm)
*Wooden knob: (M4x25mm)
2
13
Short Screw
(M3.5 x 15mm)
16
6
Wooden Knob
(38 x 30mm)
2
14
Short Pan head
screw
(M4 x 15mm)
2
METAL KNOB
(30 x 30mm)
GOES WITH
FINISHED ITEM
ONLY.
2
15
Long Pan head
screw
(M4 x 50mm)
2
7
Door pin
(5.2/13x1.2mm)
(7x10mm)
4
16
Steel Tip Bracket
4
8
Magnet
2
17
Flat Nylon Tie
2

ITEM NO.: TV-34
REVISED APR 03, 2020
Printed in Vietnam
- 5 -
NOTE: WARNING LABEL (INCLUDED)
STEP 1
Attach glasses (E) to back of doors (D), and lock it.
Attach knobs (6) to doors (D) with pan head screws (5) as shown below. Tighten with a screwdriver.

ITEM NO.: TV-34
REVISED APR 03, 2020
Printed in Vietnam
- 6 -
STEP 2
Attach panels (G) to top (A) and bottom panel (B) with bolts (1), and washers (2) and (3) as shown
below. Tighten with Allen key (4).
Attach doors (D) to top (A) and bottom (B) with door pins (7) as shown below.
Attach magnets (8) to top (A) with pan head screws (9) as shown below. Tighten with a screwdriver.
STEP 3
Attach side panels (F) to the unit with bolts (1), and washers (2) and (3) as shown below. Tighten with
Allen key (4).

ITEM NO.: TV-34
REVISED APR 03, 2020
Printed in Vietnam
- 7 -
STEP 4
Attach connector (K) to the top (A) and bottom panel (B) with screws (11) as shown below. Tighten
with a screwdriver.
Slide back panels (I) and (J) into the grooves as shown below. Then attach back panels to the
bottom panel (B) with pan head screws (10). Tighten with a screwdriver.
TEP 4
STEP 5
Insert brackets (12) into the unit as shown below. Place shelves (C) and (H) on the brackets and
attach with screws (13). Tighten with a screwdriver.

ITEM NO.: TV-34
REVISED APR 03, 2020
Printed in Vietnam
- 8 -
STEP 6
Attach brackets (16) to the back of the unit with screws (14) through the smaller holes in the brackets as
shown below.
Important!
Properly attach the other brackets (16) to the wall in an area of drywall or plaster with a wood stud:
Mark the attachment point(s) with a pencil at the appropriate height positioned over the wood
stud(s) in the wall.
Place the unit into position so both mounting brackets are vertically in line.
Properly attach the other brackets (16) to the wall stud with screws (15) through the smaller holes as
shown below.
Lace the end of flat nylon ties (17) through the larger holes in each mounting bracket. Bring both ends
together and slide the flat ends through the locking ends and draw it through until all slack is removed.
Confirm that the strap is securely laced and locked.