Whitewood Furniture T-42110XXA User manual

ITEM NO.: T-42110XXA AND T-42110XXB
ISSUED JUL 24, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: 42 X 110 DINING TABLE
:
T-42110XXA AND T-42110XXB

ITEM NO.: T-42110XXA AND T-42110XXB
ISSUED JUL 24, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws, bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
-Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your table. Protect the surface of the table with cloth if you are using any product
with rubber feet or base.

ITEM NO.: T-42110XXA AND T-42110XXB
ISSUED JUL 24, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 3 -
PART LIST T-42110XXA
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
A
Top 1
PART LIST T-42110XXB
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
B
Base 2
C
Cross Bar
1
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NOTE: HARDWARE IS PACKED IN CARTON T-42110XXB.
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Long bolt
(M8 x 70mm) 10
2
Lock Washer
(F8.5 x 13mm) 8
3
Flat Washer
(2 x F8.5 x 19mm) 8
4
U –Washer
M8 2
5
Allen Key
(M4 x 30mm x 110mm)
1

ITEM NO.: T-42110XXA AND T-42110XXB
ISSUED JUL 24, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 4 -
STEP 1
Use the Allen key (5) to loosen the bolts and washers, and then remove support rails from bottom of
the table top (A) as shown below.
Take out two table leaves from the carton box, then re-attach support rails to the table top as shown
below.

ITEM NO.: T-42110XXA AND T-42110XXB
ISSUED JUL 24, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 5 -
STEP 2
Insert crossbar (C) into the bases (B), and then attach with bolts (1) and u-washers (4) as shown
below. Tighten with Allen key (5).
STEP 3
Attach bases (B) to top (A) with bolts (1), and washers (2) and (3) as shown below. Tighten with Allen key (5).

ITEM NO.: T-42110XXA AND T-42110XXB
ISSUED JUL 24, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 6 -
STEP 4
Unlock the table top (A) from both sides underneath the top as shown below.
Pull the two parts of the table top apart.
STEP 5
Fold two aprons of the center leaves and put them underneath the table top as shown below.

ITEM NO.: T-42110XXA AND T-42110XXB
ISSUED JUL 24, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 7 -
STEP 6
Push the table top closed. Lock the mechanism underneath two sides of the table top as shown below.
STEP 7
Unlock the table top from both sides underneath the top as shown below. Pull the two parts of the
table top apart.
Unfold two aprons of the center leaves as shown below.
Place the leaves in the center of the open table top. Push the table top closed. Lock the mechanism
underneath two sides of the table top as shown below.