Whitewood Furniture SV-39 User manual

ITEM NO.: SV
-
39
REVISED JAN 22, 2013
Printed in Vie
tnam
- 1 -
`
Description
Item No.
: OLDE WORLD SERVER
: SV-39
ASSEMBLY INSTRUCTIONS
THIS ITEM IS PACKED IN 2 CARTONS

ITEM NO.: SV
-
39
REVISED JAN 22, 2013
Printed in Vie
tnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to beginning
assembly, however, make sure all parts and hardware are included and free of obvious defect. If a part is
missing or defective, please contact the store where purchased. If hardware is missing, or you need help with
assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from
being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: SV
-
39
REVISED JAN 22, 2013
Printed in Vie
tnam
- 3 -
PART
LIST
SV
–
39
A
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Q
ty
Sketch
NO
Description
Q
ty
Sketch
A Table top 1 B Bottom panel 1
C Leg 4
PART LIST
SV
–
39
B
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
D
Side panel
(L – R)
2 E
Side
shelf 2
F
Door
( L – R)
2
G
Back
panel 1
I
Center
shelf
1

ITEM NO.: SV
-
39
REVISED JAN 22, 2013
Printed in Vie
tnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Q
ty
Sketch
1
Short bolt
(M6x30mm)
12 2
Long bolt
(M6x50mm)
8
3
Hexagon nut
(M8x7mm)
8 4
Flat washer
(8.5 x 19mm)
8
5
Lock washer
(8.5 x 13mm)
8 6
Flat Washer
(6.5 x19mm)
20
7
Lock Washer
(6.5 x11mm)
20 8 Shelf support
bracket 4
9
Knob
(35x30mm)
6 10
Pan head screw
(M4x30mm)
6
11
Door pin
(5.2/13x1.2mm)
(7x10mm)
4 12 Long screw
(M4x30mm)
1
13 Steel band 1 14
Screw
(M3.5 x15mm)
6
15 Screw
(M3.5 x15mm)
12 16 Warning label 3
17 Allen Key
(4x80mm)
1 18
Wrench
(13mm)
1
NOTE: PACKED IN CARTON SV-39B

ITEM NO.: SV
-
39
REVISED JAN 22, 2013
Printed in Vie
tnam
- 5 -
STEP 1
Attach side panel (D) to top (A) with bolts (1), washers (6) and (7) as shown below. Tighten with allen
key (17).
STEP 2
Attach doors (F) (from STEP 1) to top (A) and bottom (B) with door pins (11).
Attach bottom panel (B) to side panel (D),) with bolts (1) and washers (6) and (7) as shown below.
Tighten with allen key (17).

ITEM NO.: SV
-
39
REVISED JAN 22, 2013
Printed in Vie
tnam
- 6 -
STEP 3
Position the side shelf (E) to side panel (D) as shown below.
Attach legs (C) to top (A) with washers (4) and (5), and nuts (3). Tighten with the wrench (18).
Attach legs (C) to side shelf (E) and bottom panel (B) with bolts (2) and washers (6) and (7) as shown
below. Tighten with allen key (17).
STEP 4
Attach back panel (G) with screws (15). Tighten with a screwdriver.
TEP 4

ITEM NO.: SV
-
39
REVISED JAN 22, 2013
Printed in Vie
tnam
- 7 -
STEP 5
Place the center shelf (I) on the shelf support brackets (8) and secure with screws (14) as shown
below. Tighten with a screwdriver.
STEP 6
Attach knobs (9) to front of drawers and doors (F) with screws (10). Tighten with a screwdriver.
Stick the Warning labels (15) on side of drawers before use.

ITEM NO.: SV
-
39
REVISED JAN 22, 2013
Printed in Vie
tnam
- 8 -
STEP 7
Attach steel band (13) to the unit with screws (14). Then attach the steel band to a wall with screw
(12) as shown below (to secure the product and prevent tipping).