Whittier Wood Furniture 1382AFGACg User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 06/14
Model #
1382AFGACg;
1382AFCAFg
McKenzie Cal-King
Bookcase
Headboard
AFGAC = Glazed Antique Cherry finish
AFCAF = Caffè finish
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended for commercial use.
Unload items before you move this unit.
Before you load or move this unit, tighten all screws and supports.
Do not overload the concealed storage areas.
Do not overload the cubbies.
Before you begin your project, completely read the Assembly
Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement
floor).
Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
This assembly requires two people.
WARNING
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.

1382AFGACg; 1382AFCAFg McKenzie Cal-King Bookcase Headboard
Parts List
1382AFGACg_1382AFCAFg —Page 2 —06/14
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
Ag
Headboard Assembly
1
E
#8 x 1-1/4" Black Screw (inserted)
12
H
1/4" Flat Washer (inserted)
6
R
Assembled Door (attached)
2
Sg
False Bottom
4
XA
Top Assembly (attached)
1
XB
Power Bar and USB (installed)
1
YA
Large Adjustable Glide (installed)
2
YB
#8 x 5/8" Pan Head Screw (inserted)
8
YG
#14 x 1-1/4" Pan Head Screw
6
YJ
#8 x 1-3/8" Lo-Profile Screw (inserted)
10
YL
#8 x 7/8" Black Lo-Profile Screw (inserted)
4
YQ
#6 x 3/4" Flat Head Screw (inserted)
1
YR
#8 Washer (inserted)
1
YS
Wood Dowel (inserted)
2
YT
1/4" x 1-1/2" Hex Bolt (inserted)
6
ZA
Hinge (installed)
6
ZB
Magnetic Plate (installed)
4
ZC
Magnetic Catch (installed)
4
ZE
Door Stay (attached)
2
ZF
#6 x 5/8" Undercut Screw ZN (inserted)
8
ZG
Door Stay Support (attached)
2
ZH
#6 x 1-1/4" Black Pan Head Screw (inserted)
6
ZI
#6 x 5/8" Undercut Screw AB (inserted)
44

1382AFGACg; 1382AFCAFg McKenzie Cal-King Bookcase Headboard
Parts List
1382AFGACg_1382AFCAFg —Page 3 —06/14
Part
Description
Quantity
ZJ
#6 x 5/8" Philtruss Screw (inserted)
16
ZK
Washer
6
ZN
#8 x 1-1/4" Pan Head Screw (inserted)
10
ZO
#8 x 2-1/4" Black Screw (inserted)
6
ZP
#8 x 1" Black Screw (inserted)
16
ZQ
Left Bracket (attached)
2
ZR
Right Bracket (attached)
2
ZS
Wire Clip Screw (attached)
8
ZT
Tack Glide (attached)
4
ZU
1/4" T-Nut (inserted)
6
ZZ
Corner Brace (attached)
2

1382AFGACg; 1382AFCAFg McKenzie Cal-King Bookcase Headboard
Assembly Instructions
1382AFGACg_1382AFCAFg —Page 4 —06/14
Tools Required: Drill, 1/8" bit, Phillips Screwdriver, Slotted Screwdriver.
Optional: 7/16" open end or box end wrench.
NOTE: Use this instruction and hardware kit included with this 1382 McKenzie Cal-King
Bookcase Headboard ONLY if you are using a Hollywood frame.
IF you are using this product with Whittier Wood Furniture Footboard and Pedestal kits,
disregard this instruction and hardware and use what is included with your Footboard kit.
Note: Assembly can be separated into three pieces for ease of maneuvering through narrow
halls and stairways; if you need to perform this process see steps 7 through 11.
1. Remove the metal brackets attached to the Headboard (Ag).
2. Place the Headboard (Ag) against the end brackets of the frame and mark the locations for the
screws. Drill pilot holes approximately 1-1/4" deep. To make sure you don’t drill deeper,
measure 1-1/4" up from the end of the drill bit and wrap a piece of tape around the bit. Stop
drilling when the edge of the tape meets the wood.
3. Position the Headboard (Ag) against the frame and attach using six #14 x 1-1/4" Pan Head
Screws (YG) and six Washers (ZK).
4. Place your bed in its final position. To level the headboard, reach behind the bookcase front legs
and, using a slotted screwdriver, find the Large Adjustable Glide (YA). Using a slotted screw
driver, rotate the Large Adjustable Glides (YA) clockwise until they bear weight.
See Figures 4, 4a and 4b.
This is important if the bookcase headboard sits upon a carpet tack strip.
Fig. 4
Fig. 4a
Fig. 4b
The top of the Large
Adjustable Glide (YA)
is slotted.
YA
ZZ
Hollywood bed frame
removed for illustration
purposes.

1382AFGACg; 1382AFCAFg McKenzie Cal-King Bookcase Headboard
Assembly Instructions
1382AFGACg_1382AFCAFg —Page 5 —06/14
5. Open the Door (R). To adjust the brake tension on the Door Stay (ZE) turn the screw on the
Door Stay Support (ZG) clockwise to loosen or counterclockwise to tighten. See Figures 5 and
5a.
6. Unwrap the False Bottoms (Sg) and place them on top of the rails in the Headboard Assembly
(Ag). Make sure the finger holes face forward as shown in Figure 6. After you have placed your
electronics inside the cubbies, use the Wire Clips (ZS) on the underside of the cubbies to secure
the wires. Close the door tightly making sure the magnetic catches and plates securely touch.
Fig. 6
Ag
R
Sg
Sg
Sg
Sg
ZE
L
o
o
s
e
n
T
i
g
h
t e
n
Fig. 5a
Fig. 5
ZG

1382AFGACg; 1382AFCAFg McKenzie Cal-King Bookcase Headboard
Assembly Instructions
1382AFGACg_1382AFCAFg —Page 6 —06/14
7. To divide this larger unit into three sub-assemblies, start by removing the Top Assembly (XA).
Remove the #6 x 3/4" Flat Head Screw (YQ) and #8 Washer (YR) connecting the Backs to the
Vertical Divider, and the #6 x 5/8" Philtruss Screws (ZJ) connecting the backs to the Top
Assembly. Do not remove the Backs. See Figures 7 and 7a.
8. Figure 8 shows the locations of the screws that need to be removed. You can access these from
the front of the unit. Remove the #8 x 1-3/8" Lo-Profile Screws (YJ) attaching the Sides and
Vertical Dividers to the Top, and #8 x 1-1/4" Pan Head Screws attaching the Front Apron to the
Top. Carefully remove the Top Assembly (XA) from the Case. See Figures 8 and 8a.
Fig. 8
YJ
x 10
ZN
x 8
YJ
ZN
Backs removed for illustration purposes only.
Fig. 8a
XA
Fig. 7
YR
YQ
Fig. 7a
YQ
x 1
YR
x 1
ZJ
x 8
ZJ

1382AFGACg; 1382AFCAFg McKenzie Cal-King Bookcase Headboard
Assembly Instructions
1382AFGACg_1382AFCAFg —Page 7 —06/14
9. Remove the #8 x 1-1/4" Pan Head Screw (ZN) connecting the Top Aprons. Open the Doors and
remove the 1/4" x 1-1/2" Hex Bolts (YT) and 1/4" Flat Washers (H) See Figures 9, 9a and 9b.
10. Carefully separate the two halves of the Case Assembly. See Figures 10 and 10a.
11. After moving the headboard sections into your room reassemble the Headboard by reversing
these steps.
Fig. 9
H
YT
Fig. 9a
ZN
Fig. 9b
H
x 6
YT
x 6
ZN
x 1
Fig. 10
Fig. 10a