Whittier Wood Furniture McKenzie 1113GAC User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 12/15
Model #
1113GAC;
1113CAF
4-Drawer McKenzie
Nightstand
GAC = Glazed Antique Cherry finish
CAF = Caffè finish
Assembly Instructions
IMPORTANT NOTES:
•For normal household use only. Not recommended for commercial use.
•Do not climb, sit or stand on this piece of furniture.
•Do not overload the drawers.
•Unload items before you move this unit.
•This assembly requires two people.
WARNING
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CUSTOMER SERVICE
If you ever have questions about your furniture, please do not hesitate to contact us. In the unlikely event you need a
replacement part; we can make those parts available through an authorized Whittier Wood Furniture dealer. If you
cannot order replacement parts through your dealer, please contact our customer service department.
Hours: Our friendly customer service staff can be reached:
Monday-Friday 8:00 a.m. to 5:00 p.m. (Pacific Time).
You may leave a message 24 hours a day, seven days a week.
Customer Service: 800-653-3336 • Outside the U.S.: 541-687-0213
Fax: [phone]• Email: [email protected]
Thank you for allowing us to help you furnish your
home. We are certain you will be delighted with
your new furniture for many years to come.

1113GAC; 1113CAF 4-Drawer McKenzie Nightstand
Parts List
1113GAC_1113CAF — Page 2 — 12/15
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
A
Top Assembly (attached)
1
B
Case
1
C
Top Drawer Box (inserted)
2
D
Lower Drawer Box (inserted)
2
E
Top Drawer Face (installed)
2
F
Lower Drawer Face (installed)
2
G
Drawer Slides (pre-installed sets)
4
H
#6 x 3/4" Philtruss Screw (inserted)
24
I
#6 x 1/2" Philtruss Screw (inserted)
24
J
#8 x 1-3/8" Lo-Profile Screw (inserted)
8
K
#8 x 1-1/4" Pan Head Screw (inserted)
10
L
#8 x 7/8" Black Lo-Profile Screw (inserted)
20
M
#8 x 1-1/2" Machine Screw Tuscan (installed)
6
N
Insert Nut (inserted)
4
O
Knob (attached)
6
P
Small Adjustable Glide (installed)
4
TS
Furniture Tipping Restraint (attached)
1 set

1113GAC; 1113CAF 4-Drawer McKenzie Nightstand
Assembly Instructions
1113GAC_1113CAF — Page 3 — 12/15
Tool Required: Phillips Screwdriver, Pencil.
1. Place the unit at its final destination. Rotate the Small Adjustable Glides (P) on the bottoms of
the legs until the unit is level. See Figure 1.
Continued on Page 4
Fig. 1
P
P

1113GAC; 1113CAF 4-Drawer McKenzie Nightstand
Assembly Instructions
1113GAC_1113CAF — Page 4 — 12/15
Furniture Tipping Restraint Instructions
Before you begin this assembly, identify each part and make sure the quantities received match what is on this
list. If you need to replace a part, contact Whittier Wood Furniture customer service and refer to the following
list for its name and letter code.
Part
Description
Quantity
A
Cam Buckle and Short Strap (installed)
1
B
Plastic Bracket (installed)
1
C
1" x 1000mm Long Strap (installed)
1
D
#8 x 3" Pan Head Screw
2
E
#10 x 1" Oval Head Screw (inserted)
1
F
Washer
1
If you have a stone or tile floor or do not wish to drive screws into the corner of the baseboard
and floor see the instruction included inside the tipping restraint kit for an alternate
installation.
2. Decide where you want to place the piece of furniture in your room. Mark the baseboard with a
pencil mark directly behind the location where the tipping restraint is attached to your item.
Move the item away from the wall far enough to allow you to access the spot where the
baseboard meets the floor. Position the straps and Plastic Bracket (B) as shown in Figures 2
and 2a with the angled corners of the Plastic Bracket (B) firmly placed against the seam of the
baseboard and floor. Attach by driving #8 x 3" Pan Head Screws (D) through the holes in the
Plastic Bracket (B) into the seam below the baseboard where it meets the floor. See Figures 2
and 2a.
Fig. 2
D
x 2
Fig. 2a
Wall
Floor
D
Floor
Baseboard

1113GAC; 1113CAF 4-Drawer McKenzie Nightstand
Assembly Instructions
1113GAC_1113CAF — Page 5 — 12/15
3. Move the item back into position against the wall and reach underneath the piece of furniture to
grasp the loop in the free end of the strap. Pull the free end of the strap until portion between
the Cam Buckle (A) and the back apron of the item is tight. See Figures 3 and 3a. If you need
to move the piece of furniture reach beneath and locate the buckle which connects the two
sections of the strap and depress the release lever, then pull on the section of strap that is
between the buckle and the back apron of the furniture until there is enough slack to allow you
to pull the item away from the wall.
Fig. 3a
Fig. 3
C
Wall
Floor