Whittier Wood Furniture 2091AFGSPa User manual

Production Code:
08/11
VN
P.O. Box 2827
Eugene, OR 97402 USA
Before you load or move this unit, tighten all
screws and supports.
.
Before you begin your project, completely read the
Assembly Instructions.
For normal household use only. Not recommended
to use this product in a commercial setting.
Unload items before you move this unit.
This assembly requires two people.
Do not climb, sit or stand on or in this piece of furniture.
Do not overload the drawers or shelves.
Store this item: 1- in its box; 2- in a dry place; 3- in
temperatures that range from 40°F to 90°F (not on
a cold and possibly damp cement floor).
Periodically inspect your furniture for any loose
glue joints, screws or any other problem that might
affect the stability of your furniture. Tighten or
repair as needed.
IMPORTANT NOTES:
Congratulations!
This fine piece of furniture will make a gorgeous
addition to your home. For the best results, read the
Assembly Instructions before you begin your project.
Handle the glass plates with care. Glass is fragile.
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent tip-over:
Correctly installing tipping restraints may
reduce but will not eliminate the risk of tip-over.
Place heaviest items in the bottom drawers.
Unless specifically designed to accommodate,
do not set TVs or other heavy objects on top of
this product.
Never allow children to climb or hang on drawers,
doors or shelves.
Never open more than one drawer at a time.
64"W Pacific
Sound Bar Console
Assembly Instructions
Model #
2091AFGSPa
2091AFCAFa
AFGSP = Glazed Spice finish
AFCAF = Caffè finish
Service Policy: We will replace any part that is
defective, missing or damaged during assembly.
For a replacement part, contact Whittier Wood
Products customer service department by phone,
fax, mail or email.
To Order: Provide the finish and furniture model number
(upper left corner of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one
or two business days from the time we receive your
request. Please allow five to ten business days for delivery.
CALL US FIRST! Do not return this item to the store.
800-653-3336 • Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Hours: Our friendly customer service staff can be
reached Monday-Friday 7:00 a.m. to 5:00 p.m.
(Pacific Time). You may leave a message
24 hours a day, seven days a week.

2091AFGSPa_2091AFCAFa — Page 2 — 08/11
2091AFGSPa; 2091AFCAFa
64"W Pacific Sound Bar Console — Parts List
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and model number.
Part Description Quantity
ATop (attached) 1
BAdjustable Shelf (attached)
Case
4
Ca
Speaker Door (attached)
1
D Removable Back (installed) 2
EDoor Frame (installed) 2
FDoor Glass (installed) 2
Ga 1
Small Drawer Box (installed)
H2
Small Drawer Face (installed)
I2
Large Drawer Box (installed)
J3
Large Drawer Face (installed)
K 3
LGlass Retainer (inserted) 1
M Shelf Bracket (attached) 16
N #6 x 1/2" Undercut Screw (inserted) 16
P Butler Hinge (attached) 2
Q Magnetic Push Lock (attached) 2
R #5 x 5/8" Flat Head Screw (inserted) 12 (AFGSP)
0 (AFCAF)
4 (AFGSP)
16 (AFCAF)
S Magnetic Plate (attached) 2
T #6 x 5/8" Undercut Screw (inserted)
U Drawer Slides (installed) 5 sets
V #6 x 3/4" Philtruss Screw (inserted) 30
W #6 x 1/2" Philtruss Screw (inserted) 34
XAssembled Foot (attached) 2
ZB Small Adjustable Glide (installed) 6

2091AFGSPa_2091AFCAFa — Page 3 — 08/11
2091AFGSPa; 2091AFCAFa
64"W Pacific Sound Bar Console — Parts List continued
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and model number.
ZC #8 x 2" Black Screw (inserted) 4
ZG Knob (attached) 2
ZH #8 x 1-1/4" Machine Screw (installed) 2
ZI Handle (attched) 5
ZJ M4 x 41mm Machine Screw (installed) 10
ZD Hinge (attached) 4
ZE Hinge Plate (attached) 4
ZF #6 x 3/4" P.O. Screw 16
ZK Drawer Stop (attached) 4
Turn Button (attached)
ZL 8
ZM #6 x 5/8" Philtruss Screw (inserted) 30
ZN #8 x 1-1/4" Pan Head Screw (inserted) 34
ZO #8 x 1-3/16" Pan Head Screw (inserted) 6
ZP #8 x 1-1/4" Black Screw (inserted) 41
ZQ #8 x 1" LoProfile Screw (inserted) 20
ZR Flat Washer (inserted) 2
ZS Hex Bumper (attached) 2
ZT Fitted Back (attached) 1
ZW Chain (attached) 2
ZU Speaker Spacer 2
ZV Pad Strip (attached) 4
TR Tipping Restraint 2 sets
YA
ZX Cleat (attached) 1
ZY Push Plate 2
ZZ 1/2" Dark Antique Brad 4
8
#8 x 1-1/8" LoProfile Screw (inserted)
YB 43mm x 12mm Pan Head Screw (inserted)
YC 6 Insert Nut (inserted)

2091AFGSPa_2091AFCAFa — Page 4 — 08/11
Fig. 2
ZY
ZZ
2. Remove the Speaker Door (Ga) and place it face-up on a clean protected surface. Center a
Push Plate (ZY) over the right Magnetic Plate (S) and attach with two 1/2" Dark Antique
Brads (ZZ). Repeat for the left side. See Figure 2. Attach the Door.
x 2ZY
x 4ZZ
ZY
Ga
ZZ
(back view)
S
S
Step two is optional: Attach the Push Plates (ZY) if the console will be
placed in a high-use area such as a retail sales floor where the Sound
Bar Speaker Door will be opened and closed often.
2091AFGSPa; 2091AFCAFa 64"W Pacific Sound Bar Console
Assembly Instructions
Tools Required: Phillips Screwdriver, Hammer
1. Place the console at its final destination. Rotate the Small Adjustable Glides (ZB) on
the bottoms of the legs until the unit is level. See Figure 3.
Fig. 3
3. To open the Speaker Door (Ga), simultaneously press the Push Plates or both corners until the
magnets release. Gently grasp the middle of the door and pull it open. To shut the door, push
gently but firmly on the Speaker Door (Ga) until the two Magnetic Plates (S) make secure contact
with the Magnetic Push Locks (Q).
If you did not install the Push Plates, gently press on both corners until the magnets release.
See Figure 3.
If you need to install your sound bar from the back, remove the #6 x 1/2" Philtruss Screws (W) and
pull away the fitted back (ZT). After installing the component, replace the Fitted Back and attach
with the #6 x 1/2" Philtruss Screws.
Q
S
Q
S
ZB ZB
ZB
X
ZT
Ga

2091AFGSPa_2091AFCAFa — Page 5 — 08/11
Fig. 4
4.
Fig. 4a
ZU
ZU
ZU
If your center sound bar needs to sit above the edge of the speaker door, place the two Speaker
Spacers (ZK) into the sound compartment so the Pad Strips (ZL) face down. Place the speaker
on top of the Spacers. See Figures 4 and 4a.
Fig. 5a
Fig. 5
Locked
ZK
ZL
To insert your media components and access wires into the console more easily, remove
the Removable Backs (D). To do so, unlock the Turn Buttons (ZL) as shown in
Figures 5 and 5b. Slide the Backs away and place them off to the side. After inserting your
components, fit the Backs behind the Drawer Stops (ZK) and lock the Turn Buttons. See
Figures 5, 5a and 5b.
5.
ZK
ZL
D
ZT
D
Fig. 5b
Unlocked

2091AFGSPa_2091AFCAFa — Page 6 — 08/11
6. Determine where you want to place the Adjustable Shelves (B). To support each shelf, tap the
Shelf Brackets (M) into the four holes with the flat side down. Insert the shelf as shown in
Figure 6. You may fasten the brackets to the shelf by inserting a #6 x 1/2" Undercut Screw (C).
Repeat for each shelf. See Figures 6 and 6a.
Fig. 6a
Fig. 6
N
M
Doors removed for illustration purposes.
B
B
X
7. If you need to adjust the doors, follow the above instructions.
Fig. 7 Fig. 7a
Hinge
Arm ZD
ZE
2
Door
3
2
3
1
Side adjustment 4mm (5/32")
To move the door towards the side
panel, loosen screw ‘1’ and tighten
screw ‘2’. To move the door away
from the side panel, loosen screw
‘2’ and tighten screw ‘1’.
Depth Adjustment 4mm (5/32")
Loosen screw ‘2’ (just one turn),
adjust the door to the desired position
and re-tighten the screw.
Height Adjustment 4mm (5/32")
Loosen screw ‘3’, adjust the door to
the desired position and re-tighten
the screw.

2091AFGSPa_2091AFCAFa — Page 7 — 08/11
Fig. 8b
T4
T1
T2
T1
T1
T3
T3
T4
Fig. 8c
Fig. 8a
Fig. 8d
Tighten the Nylon Restraint
Strap (T2) so there is no slack.
Pull tight
8. Position the unit at the desired location. Locate two studs in the wall behind the unit. Attach a
Clip (T1) to one wall stud with two #8 x 2" Black Screws (T3). See Figure 8a. Attach a second
clip to the unit with two #8 x 1" Pan head Screws (T4). See Figure 8b. Connect the two clips with
the Nylon Restraint Strap (T2). Pull the Nylon Restraint Strap (T2) tight so there is no slack. See
Figures 8c and 8d. Repeat this procedure to attach the second tipping restraint. If you cannot locate
two studs, purchase the proper wall attachment hardware for your type of wall and secure the unit.
Tipping restraint: