Whittier Wood Furniture Pacific 2089AFGSP User manual

Production Code:
09/10
VN
P.O. Box 2827
Eugene, OR 97402 USA
Before you load or move this unit, check to make
sure all screws and supports are tight.
.
Before you begin your project, completely read the
Assembly Instructions.
For normal household use only. Not recommended
for commercial use.
Unload items before you move this unit.
This Assembly requires two people.
Do not climb, sit or stand on this piece of furniture.
Do not not overload the shelves on this unit.
Store this item: 1- in its box; 2- in a dry place; 3- in
temperatures that range from 40°F to 90°F (not on
a cold and possibly damp cement floor).
Periodically inspect your furniture for any loose
glue joints, screws or any other problem that might
affect the stability of your furniture. Tighten or
repair as needed.
IMPORTANT NOTES:
45"W Pacific
Sound Bar Console
Congratulations!
This fine piece of furniture will make a gorgeous
addition to your home. For the best results, read the
Assembly Instructions before you begin your project.
Handle the glass plates with care. Glass is fragile.
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent tip-over:
Use of tip-over restraints may only reduce
but not eliminate the risk of tip-over.
Place heaviest items in the bottom drawers.
Unless specifically designed to accommodate,
do not set TVs or other heavy objects on top of
this product.
Never allow children to climb or hang on drawers,
doors or shelves.
Never open more than one drawer at a time.
Assembly Instructions
Model #
2089AFGSP;
2089AFCAF
AFGAC = Glazed Spice finish
AFCAF = Caffè finish
Service Policy: We will replace any part that is
defective, missing or damaged during assembly.
For a replacement part, directly contact Whittier
Wood Products customer service department by
phone, fax, mail or email.
To Order: Provide the furniture model number (found
above the illustration of this unit), the part letter,
production code, quantity needed, reason for replacement,
and your full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one
or two business days from the time we receive your
request. Please allow five to ten business days for delivery.
CALL US FIRST! Do not return this item to the store.
800-653-3336 • Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Hours: Our friendly customer service staff can be
reached Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific
Time). You may leave a message 24 hours a day,
seven days a week.

2089AFGSP_2089AFCAF — Page 2 — 09/10
2089AFGSP; 2089AFCAF 45"W Pacific
Sound Bar Console — Parts List
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and model number.
Part Description Quantity
ATop (attached) 1
BAdjustable Shelf
Case only
2
C
Speaker Door (attached)
1
DRemovable Back (installed) 2
EDoor Frame (installed) 2
FDoor Glass (installed) 2
G1
HGlass Retainer (inserted) 1
L Shelf Bracket (attached) 8
M #6 x 1/2" Undercut Screw (inserted) 8
O Butler Hinge (attached) 2
P Magnetic Push Lock (attached) 2
Q #5 x 5/8" Flat Head Screw (inserted) 16 (AFGSP)
4 (AFCAF)
R Magnetic Plate (attached) 2
S #6 x 5/8" Undercut Screw (inserted) 4 (AFGSP)
16 (AFCAF)
T Hinge (attached) 4
U Hinge Plate (attached) 4
V#6 x 3/4" P.O. Screw 16
W Drawer Stop (attached) 4

2089AFGSP_2089AFCAF — Page 3 — 09/10
2089AFGSP; 2089AFCAF 45"W Pacific Sound Bar Console
— Parts List continued
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and model number.
Part Description Quantity
Turn Button (attached)
X
T-Nut (inserted)
8
Y#6x5/8" Philtruss Screw (inserted) 28
ZN #6x1/2" Philtruss Screw (inserted) 4
ZA Knob (attached) 2
ZB #8 x 1-1/4" Machine Screw (installed) 2
ZC 4
ZD Small Adjustable Glide (installed) 4
ZE #8x1-1/4" Pan Head Screw (inserted) 14
ZF #8x1-3/16" Pan Head Screw (inserted) 34
ZG #8 x 1-1/4" Black Screw (inserted) 26
ZH Flat Washer (inserted) 2
ZI Hex Bumper (attached) 2
ZJ Fitted Back (attached) 1
ZM Chain (attached) 2
ZK Speaker Spacer 2
ZL Pad Strip (attached) 4
TR Tipping Restraint 2 sets

2089AFGSP_2089AFCAF — Page 4 — 09/10
2089AFGSP; 2089AFCAF 45"W Pacific Sound Bar Console
Assembly Instructions
Tool Required: Phillips Screwdriver
Place the console at its final destination. Rotate the Small Adjustable Glides (ZD) found on
the bottoms of the legs until the unit is level.
Fig. 2
2. To open the Speaker Door (G), press both corners until the magnets release. Gently grasp the
middle of the door and pull it open. To shut the door, gently but firmly push on the Speaker Door (G)
until the two Magnetic Plates (R) make secure contact with the Magnetic Push Locks (P). See Figure 2.
If you need to install your sound bar from the back, remove the 16 #6 x 5/8" Philtruss Screws (Y) and
pull away the Fitted Back (ZJ). After installing the component, replace the Fitted Back (ZJ) and attach
with the 16 #6 x 5/8" Philtruss Screws (Y).
1.
P
P
RR
G
ZJ
If your sound bar speaker needs to sit up off the base of the storage compartment, place the two
Speaker Spacers (ZK) into the drawer so the Pad Strips (ZL) face down. Place the sound bar
speaker on top of the Spacers. See Figures 3 and 3a.
3.
Fig. 3
Fig. 3a
ZK
G
ZK
ZK

2089AFGSP_2089AFCAF — Page 5 — 09/10
Fig. 4a
Fig. 4b
Fig. 4
Locked Position
Unlocked Position
W
X
W
X
ZJ
DD
To insert your media components and access wires into the console more easily, you may want to
remove the Removable Backs (D). To do so, unlock the Turn Buttons (X) as shown in Figures 4 and 4b.
Slide the Backs away and place them off to the side. To put them back into place, slide the Backs
behind the Drawer Stops (W) and position the Turn Buttons so that they are locked. See Figures
4, 4a and 4b.
4.
5. To move the Adjustable Shelves (B), remove the #6 x 1/2" Undercut Screws (M) and the Shelves
(B). Reposition the Shelf Brackets (L) to the desired positions, replace the shelf and insert the screws.
See Figures 5 and 5a.
Fig. 5a
Fig. 5
M
L
Doors removed for illustration purposes.
B

2089AFGSP_2089AFCAF — Page 6 — 09/10
6. If you need to adjust the doors, please follow the above instructions.
Fig. 6 Fig. 6a
Hinge
Arm G
H
2
Door
3
2
3
1
Side adjustment 4mm (5/32")
To move the door towards the side
panel, loosen screw ‘1’ and tighten
screw ‘2’. To move the door away
from the side panel, loosen screw
‘2’ and tighten screw ‘1’.
Depth Adjustment 4mm (5/32")
Loosen screw ‘2’ (just one turn),
adjust the door to the desired position
and re-tighten the screw.
Height Adjustment 4mm (5/32")
Loosen screw ‘3’, adjust the door to
the desired position and re-tighten
the screw.
Fig. 7b
T4
T1
T2
T1
T1
T3
T3
T4
Fig. 7c
Fig. 7a
Fig. 7d
Tighten the Nylon Restraint
Strap (T2) so there is no slack.
Pull tight
7. Locate two studs in the wall behind the unit. Attach a Clip (T1) to one wall stud with two #8 x 2" Black
Screws (T3). See Figure 7a. Attach a second clip to the unit with two #8 x 1" Pan Head Screws (T4).
See Figure 7b. Connect the two clips with the Nylon Restraint Strap (T2). Pull the Nylon Restraint
Strap (T2) tight so there is no slack. See Figures 7c and 7d. Repeat this procedure to attach the
second tipping restraint. If you cannot locate two studs, purchase the proper wall attachment hardware
for your type of wall and secure the unit.
Tipping restraint: