Whittier Wood Furniture McKenzie 2319GACc User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 10/17
Model #
2319GACc
2319CAFc
2319FSTc
McKenzie King Mantel
Storage Bed
GAC = Glazed Antique Cherry finish
CAF = Caffè finish
FST = Fieldstone finish
Assembly Instructions
IMPORTANT NOTES:
•For normal household use only. Not recommended for commercial use.
•Remove items before you move this unit.
•Do not overload the drawers.
•This assembly requires two people.
WARNING
Drilling, sawing, sanding or machining wood products can expose you to
wood dust, a substance known to the state of California to cause cancer.
Avoid inhaling wood dust or use a dust mask or other safeguards for
personal protection.
For more information go to: www.p65warnings.ca.gov/wood
This product can expose you to chemicals, including formaldehyde,
which are known to the State of California to cause cancer.
For more information go to: www.p65warnings.ca.gov/furniture
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CUSTOMER SERVICE
If you ever have questions about your furniture, please do not hesitate to contact us. In the unlikely event you need a
replacement part; we can make those parts available through an authorized Whittier Wood Furniture dealer. If you
cannot order replacement parts through your dealer, please contact our customer service department.
Hours: Our friendly customer service staff can be reached:
Monday-Friday 8:00 a.m. to 5:00 p.m. (Pacific Time).
You may leave a message 24 hours a day, seven days a week.
Customer Service: 800-653-3336 • Outside the U.S.: 541-687-0213
Fax: [phone]• Email: [email protected]
Thank you for allowing us to help you furnish your
home. We are certain you will be delighted with
your new furniture for many years to come.

2319GACc 2319CAFc 2319FSTc McKenzie King Mantel Storage Bed
Parts List
2319GACc_2319CAFc_2319FSTc — Page 2 — 10/17
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
1318GACe 1318CAFe 1318FSTe Pedestal Kit (x2)
Part
Description
Quantity
E
#8 x 1-1/4" Black Screw (inserted)
30
Id
Pedestal Kit
1
J
Small Drawer Box (assembled)
2
Kd
Large Drawer Box (assembled)
1
L
Small Drawer Face (attached)
2
Md
Large Drawer Face (attached)
1
Ne
#8 x 1-1/2" Machine Screw Tuscan (installed)
3
O
Knob (attached)
3
Pd
Deckboard
1
Q
20" Drawer Slides (installed)
3 sets
T
#8 x 2" Black Screw (inserted)
12
YD
#6 x 1/2" Philtruss Screw (inserted)
18
YE
#6 x 3/4" Philtruss Screw (inserted)
18
YL
#8 x 7/8" Black Lo-Profile Screw (inserted)
20
ZP
#8 x 1" Black Screw (inserted)
16
ZQ
Left Bracket (attached)
2
ZR
Right Bracket (attached)
2
ZX
#8 x 1-5/8" Black Screw (inserted)
16

2319GACc 2319CAFc 2319FSTc McKenzie King Mantel Storage Bed
Parts List
2319GACc_2319CAFc_2319FSTc — Page 3 — 10/17
2320GACa 2320CAFa 2320FSTa
King Mantel Headboard/Footboard Kit (x1)
Part
Description
Quantity
Aa
Headboard Assembly
1
B
Footboard Assembly
1
Rb
Center Deckboard
1
YH
Top Assembly
1
YI
#8 x 1-1/4" Pan Head Screw
6
(4 inserted)
YJ
Cam Connector (inserted)
2
YK
Cam Housing
2
ZP
#8 x 1" Black Screw (inserted)
32
ZQ
Left Bed Bracket (attached)
4
ZR
Right Bed Bracket (attached)
4
ZX
#8 x 1-5/8" Black Screw (inserted)
4

2319GACc 2319CAFc 2319FSTc McKenzie King Mantel Storage Bed
Parts List
2319GACc_2319CAFc_2319FSTc — Page 4 — 10/17
2321Wc
King Mantel Assembly Kit (x1)
Part
Description
Quantity
Da
Trestle With T-Nuts
7
E
#8 x 1-1/4" Black Screw
45
(9 inserted)
F
1/4" x 1-3/4" Hex Bolt
26
Ua
Assembled Foot
3
W
Adjustable Glide (installed)
3
YD
#6 x 1/2" Philtruss Screw
8
YG
90
o
Bracket
2
YM
#10 x 3/4" Pan Head Screw (inserted)
12
YN
18mm Washer
26
ZU
1/4" T-Nut (inserted)
28
ZY
Foot Bracket (attached)
3

2319GACc 2319CAFc 2319FSTc McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319GACc_2319CAFc_2319FSTc — Page 5 — 10/17
Tools Required: Phillips screwdriver, 7/16" open end or box end wrench and Tape measure
1. Remove the Center Deckboard (Rb) from the back of the Headboard (Aa) and place to the side.
See Figure 1.
2. NOTE: READ CAM INSTRUCTIONS NOW BEFORE YOU BEGIN THE FOLLOWING STEP.
Insert Cam Housings (YK) into the two pre-drilled holes on the Headboard Assembly (Aa) as
shown in Figure 2. Lower Top Assembly (YH) so that the Cam Connectors (YJ) fit into the
housings (YK) tighten the cam housings as indicated in the Cam-lock System instructions. See
Figures 2 and 2a.
Fig. 2
Aa
YH
YK
x 2
YK
YK
Fig. 2a
YK
YJ
Fig. 1
Shipping Straps
Rb
Aa

2319GACc 2319CAFc 2319FSTc McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319GACc_2319CAFc_2319FSTc — Page 6 — 10/17
3. Attach the Top Assembly (YH) to the Headboard Assembly (Aa) by inserting two #8x1-1/4" Pan
Head Screws (YI) into the predrilled holes in the block that is attached to the Headboard
Assembly (Aa). See Figures 3 and 3a.
4. Place both Pedestals (Id) approximately 79" apart as shown in Figure 4.
Fig. 4
79"
Id
Id
Fig. 3
YI
x 2
Fig. 3a
YI

2319GACc 2319CAFc 2319FSTc McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319GACc_2319CAFc_2319FSTc — Page 7 — 10/17
5. To attach the Footboard (B) to the Pedestal Assembly (Id), align the Brackets and slide the
Pedestal Assembly down on to the Footboard (B). See Figures 5 and 5a.
6. Repeat step five for the left side.
Fig. 6
Id
Fig. 6a
Fig. 5
Id
B
Fig. 5a

2319GACc 2319CAFc 2319FSTc McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319GACc_2319CAFc_2319FSTc — Page 8 — 10/17
7. Align the Brackets on both sides and slide the Pedestal/Footboard assembly down on to the
Headboard (Aa). See Figure 7.
Fig. 7
Aa

2319GACc 2319CAFc 2319FSTc McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319GACc_2319CAFc_2319FSTc — Page 9 — 10/17
8. Open the drawers. Face the Footboard and stand in between the first and second braces.
Place a Trestle with T-Nuts (Da) on the outside surfaces of the first upper left and right braces
so that the T-Nuts (ZU) sit near the top. See Figure 5a. Line up the upper edges of the trestle
and braces so they are nearly flush. Insert two 1/4" x 1-3/4" Hex Bolts (F) and Washers (YN)
and tighten. Repeat for the second upper brace.
Place a Trestle with T-Nuts (Da) on the outside surface of the second lower brace so that
the T-Nuts (ZU) sit near the bottom. Line up the bottom edges of the trestle and braces so they
are nearly flush. Insert two 1/4" x 1-3/4" Hex Bolts (F) and Washers (YN) and tighten.
See Figures 8 and 8a.
Fig. 8
Da
First brace
Second brace
Da
F
YN
F
YN
x 6
x 6
Footboard
Headboard removed for illustration purposes.
Fig. 8a
YN
F
Brace
Da

2319GACc 2319CAFc 2319FSTc McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319GACc_2319CAFc_2319FSTc — Page 10 — 10/17
9. Face the Headboard and stand in between the third and fourth braces. Place a Trestle with
T-Nuts (Da) on the outside surfaces of the third upper left and right braces so the T-nuts sit
near the top. See Figures 6 and 6a. Line up the upper edges of the trestle and braces so they
are nearly flush. Insert two 1/4" x 1-3/4" Hex Bolts (F) and Washers (YN) and tighten.
Place a Trestle with T-Nuts (Da) on the outside surface of the third left and right lower braces
so that the T-nuts sit near the bottom. Line up the bottom edges of the trestle and braces so
they are nearly flush. Insert two 1/4" x 1-3/4" Hex Bolts (F) and Washers (YN) and tighten.
See Figures 9 and 9a.
Repeat for the fourth braces.
Fig. 9
Fourth brace
Third brace
Da
F
F
YN
x 8
x 8
Fig. 9a
YN
F
Brace
YN
Trestle with T-Nuts (Da)
Da