Whittier Wood Furniture McKenzie 2400AFGACd User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 12/13
Model #
2400AFGACd;
2400AFCAFd
McKenzie
3-Drawer Desk
AFGAC = Glazed Antique Cherry finish
AFCAF = Caffè finish
Assembly
Instructions
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended for commercial use.
Do not climb, sit or stand on this piece of furniture.
Use a protective pad when you use the top of this piece as a writing
surface.
Do not overload the drawers.
Unload items before you move this unit.
Before you load or move this unit, tighten all screws and supports.
Before you begin your project, completely read the Assembly
Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement
floor).
Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
This assembly requires two people.
WARNING
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.

2400AFGACd; 2400AFCAFd McKenzie 3-Drawer Desk
Parts List
2400AFGACd_2400AFCAFd —Page 2 —12/13
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
Ac
Case Assembly
1
B
Top Assembly (attached)
1
C
Left Side Assembly
1
D
Leg
2
E
Drawer (inserted)
2
F
Drawer Face (installed)
2
G
Keyboard Tray Box (inserted)
1
H
Keyboard Tray Face (installed)
1
Ic
Pull-out (installed)
1
J
Drawer Slides (pre-installed set)
3
K
#6 x 3/4" Philtruss Screw (inserted)
18
L
#6 x 1/2" Philtruss Screw (inserted)
18
M
Roller Catch Kit (pre-installed set)
1
N
Left Keyboard Hinge (attached)
1
O
Right Keyboard Hinge (attached)
1
Q
Knob (attached)
2
Rd
#8 x 1-1/2" Machine Screw Tuscan (installed)
2
S
Small Knob (attached)
2
T
4 x 35mm Machine Screw (installed)
2
Ub
Twin Push Latch (attached)
1
Vd
#8 x 7/8" Black Lo-Profile Screw (inserted)
8
W
#8 x 1-1/4" Pan Head Screw (inserted)
34
X
#8 x 1-3/4" Pan Head Screw (inserted)
14
(13 inserted)

2400AFGACd; 2400AFCAFd McKenzie 3-Drawer Desk
Parts List
2400AFGACd_2400AFCAFd —Page 3 —12/13
Part
Description
Quantity
Y
#12 x 2-1/2" Pan Head Screw (inserted)
5
ZA
#8 x 1-1/4" Black Screw (inserted)
13
ZB
#8 x 2" Black Screw (inserted)
2
ZC F
Wood Dowel (inserted)
1
ZD
3/8" x 1" Insert Nut (inserted)
8
ZE
5/16" Flat Washer
8
ZF
3/8" x 2-1/2" Hex Bolt
8
ZG
Adjustable Glide (installed)
4
ZI
#6 x 1/2" Undercut Screw (inserted)
8
ZJ
3mm x 12mm Pan Head Screw (inserted)
2
ZK
1/4" x 20mm Insert Nut (inserted)
4
ZL
#8 x 1-3/8" Lo-Profile Screw (inserted)
3

2400AFGACd; 2400AFCAFd McKenzie 3-Drawer Desk
Assembly Instructions
2400AFGACd_2400AFCAFd —Page 4 —12/13
Tool Required: Phillips Screwdriver, 9/16" or Adjustable Wrench, Mallet or Padded Hammer
1. Remove the drawers from the Case Assembly (Ac). To do that, pull up on the left Drawer
Release Lever while pushing down on the right Drawer Release Lever and pull out the drawer.
See Figure 1a. Note where each drawer came from to make sure you place them back into their
correct positions.
2. Turn the Case Assembly (Ac) upside-down on a clean protected surface. Be careful not to
engage the touch-latch on the pull-out writing/working surface. Place a Leg (D) into the right
front and back corners, making sure the drilled portions of the legs face the corner blocks. Insert
four 3/8" x 2-1/2" Hex Bolts (ZF) with four 5/16" Flat Washers (ZE) through the corner blocks
and into the Legs (D). Fasten securely. See Figures 2 and 2a.
Fig. 1
Drawer Release Lever
Fig. 1a
Fig. 2a
ZE
ZF
x 4
x 4
ZE
ZF
ZF
ZE
D
Ac
Fig. 2

2400AFGACd; 2400AFCAFd McKenzie 3-Drawer Desk
Assembly Instructions
2400AFGACd_2400AFCAFd —Page 5 —12/13
3. Attach the Left Side Assembly (C) to the drawer side of the case assembly with four 3/8"x 2-1/2"
Hex Bolts (ZF) and four 5/16" Flat Washers (ZE). Fasten securely. Make sure the dowel is
correctly seated in place by tapping the Left Side Assembly with a rubber mallet. See Figure 3.
4. Using the pocket drilled hole as a guide, secure the back leg of the Left Side Assembly to the
case assembly with one #8 x 1-3/4" Pan Head Screw. See Figures 4 and 4a.
Fig. 3
Tap this area with
a rubber mallet.
ZE
ZF
x 4
x 4
ZE
ZF
C
Fig. 4
X
x 1
X
X
Fig. 4a

2400AFGACd; 2400AFCAFd McKenzie 3-Drawer Desk
Assembly Instructions
2400AFGACd_2400AFCAFd —Page 6 —12/13
5. Turn the table upright and insert the Drawers.
6. This desk features a Pull-out (Ic) that is above the two drawers on the right side. To access this
feature, push firmly on the end of the pull-out. This releases the Push Lock. Grab on to the
underside hand groove and gently pull. See Figures 6 and 6a.
Fig. 5
Fig. 6
Fig. 6a
Ic
Ic

2400AFGACd; 2400AFCAFd McKenzie 3-Drawer Desk
Assembly Instructions
2400AFGACd_2400AFCAFd —Page 7 —12/13
7. The center drawer (G) can be used as a keyboard tray or utility drawer. To use it as a keyboard
tray, open the drawer and pull down on the front. This unlocks the roller catches. To lock it back
into place, push up on the drawer front. See Figure 7.
The shortened drawer back allows easy cord access.
8. Place the desk at its final destination. To level the unit, rotate the Adjustable Glides
(ZG) found on the bottoms of the legs. See Figure 7.
9. Use a protective pad when you use the top of this piece as a writing surface.
Fig. 7
G
ZG
ZG