Whittier Wood Furniture 3460AFCAFa User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 03/14
Stayton Media
Tables
AFCAF = Caffè finish
Assembly Instructions
Model #
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended for commercial use.
Do not climb, sit or stand on this piece of furniture.
Unload items before you move this unit.
Do not overload the drawer or shelves.
Before you load or move this unit, tighten all screws and supports.
Before you begin your project, completely read the Assembly
Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement
floor).
Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
This assembly requires two people.
WARNING
Serious or fatal crushing injuries can occur from furniture tip-over. Use of
tip-over restraints may only reduce but not eliminate the risk of tip-over.
To help prevent tip-over:
Place heaviest items in the bottom drawers.
Unless specifically designed to accommodate, do not set TVs or other
heavy objects on top of this product.
Never allow children to climb or hang on drawers, doors or shelves.
Never open more than one drawer at a time.
Warning: At least one tipping restraint kit was included with your piece of
Whittier Wood Furniture. When you receive your furniture, be sure to find
and properly install the tipping restraint(s). If you cannot locate the
restraint(s), please contact us immediately for replacement.
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
3462AFCAFa
Stayton Media
Center
3460AFCAFa
Stayton Media
Console

3460AFCAFa Stayton Media Console;
3462AFCAFa Stayton Media Center
Parts List
3460AFCAFa_3462AFCAFa —Page 2 —03/14
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
3460AFCAFa
3462AFCAFa
A
Top Assembly (attached)
1
1
B
Leg
4
4
C
Lower Shelf Assembly
1
1
D
Upper Shelf Assembly
1
1
E
Back Assembly
1
1
F
Drawer Box (inserted)
1
1
G
Drawer Face (installed)
1
1
H
Drawer Slides (pre-installed sets)
1
1
I
#6 x 3/4" Philtruss Screw (inserted)
4
6
J
#6 x 1/2" Philtruss Screw (inserted)
4
6
K
#6 x 5/8" Philtruss Screw
6
6
M
#8 x 1-1/4" Pan Head Screw
42
(34 inserted)
45
(37 inserted)
Na
#8 x 1-1/2" Machine Screw Tuscan (installed)
4
4
O
#8 Washer (inserted)
18
21
P
5/16" Flat Washer
4
4
Q
3/8" x 1" Insert Nut (inserted)
4
4
R
3/8" x 2-1/2" Hex Bolt
4
4
S
1/4" x 20mm Insert Nut (inserted)
4
4
T
Pull (installed)
2
2
U
Wood Dowel (inserted)
8
8
V
Adjustable Glide (installed)
4
4
W
#8 x 7/8" Black Lo-Profile Screw (inserted)
6
6
TR
Media Zip-Tie Tipping Restraint
2 sets
2 sets
3462 shown in the illustrations.

3460AFCAFa Stayton Media Console;
3462AFCAFa Stayton Media Center
Assembly Instructions
3460AFCAFa_3462AFCAFa —Page 3 —03/14
Tools Required: Phillips Screwdriver, 9/16" or Adjustable Wrench, Rubber Mallet or Padded
Hammer
1. Remove the Drawer (F) from the Top Assembly (A). To remove the drawer, pull up on the left
side of the Drawer Release Lever while pushing down on the right Drawer Release Lever. See
Figure 1a.
2. Turn the Top Assembly (A) upside-down on a clean, protected surface. Place two Legs (B) at
the back of the Top Assembly (A), making sure the drilled corners of the legs face toward the
Corner Blocks. Attach with 5/16" Flat Washers (P) and 3/8" x 2-1/2" Hex Bolts (R). See Figures
2 and 2a.
Fig. 2
B
B
Fig. 2a
A
P
R
x 2
x 2
R
P
Fig. 1
Drawer Release Lever
Fig. 1a

3460AFCAFa Stayton Media Console;
3462AFCAFa Stayton Media Center
Assembly Instructions
3460AFCAFa_3462AFCAFa —Page 4 —03/14
3. Rotate the Top and Leg assembly so that is sets on the back legs. Turn the Lower Shelf
Assembly (C) and the Upper Shelf Assembly (D) bottom-side-down and place the dowels into
the dowel holes in the Legs. See Figure 3.
4. Using the dowels as guides, place the remaining Legs (B) in the remaining two corners making
sure the drilled corners of the Legs face toward the Corner Blocks. See Figures 4 and 4a.
Fig. 4
Fig. 4a
Fig. 3
C
D

3460AFCAFa Stayton Media Console;
3462AFCAFa Stayton Media Center
Assembly Instructions
3460AFCAFa_3462AFCAFa —Page 5 —03/14
5. Attach the legs to the Top Assembly with 5/16" Flat Washers (P) and 3/8" x 2-1/2" Hex Bolts (R)
See Figures 5 and 5a.
6. Turn the unit onto its top and using the pocket holes as guides, secure the Lower Shelf
Assembly (C) and the Upper Shelf Assembly (D) to the Legs (B) with eight #8 x 1-1/4" Pan Head
Screws (M). See Figures 6 and 6a.
Fig. 6
M
x 8
Fig. 6a
M
Fig. 5
Fig. 5a
P
R
x 2
x 2
P
R

3460AFCAFa Stayton Media Console;
3462AFCAFa Stayton Media Center
Assembly Instructions
3460AFCAFa_3462AFCAFa —Page 6 —03/14
7. Lay the unit with the drawer opening face down. The back apron of the Top Assembly has pre-
punched location holes. Place the Back Assembly (E) with the horizontal cleat of the top edge
against the back apron of the Top Assembly. Attach by inserting three #6 x 5/8" Philtruss
Screws (K) through the pre-punched location holes in the Back Apron. Insert three additional #6
x 5/8" Philtruss Screws through the holes in the bottom edge of the Back Assembly into the
Lower Shelf Assembly.
8. Turn the table upright and insert the Drawer. See Figure 8.
9. Place the unit at its final destination. To level the table, rotate the Adjustable Glides (V) found on
the bottoms of the legs. See Figure 8.
Continued on Page 7
Fig. 8
V
V
Fig. 7
K
x 6
E
K
(Front View of
Back Assembly)
Fig. 7a
E
TOP

3460AFCAFa Stayton Media Console;
3462AFCAFa Stayton Media Center
Assembly Instructions
3460AFCAFa_3462AFCAFa —Page 7 —03/14
10. Position the unit at the desired location. Locate a stud in the wall behind the unit near each Leg.
Do not choose a stud that will be located behind the center back panel. A strong small magnet
is helpful to locate the studs in the wall. The magnet will help you find the nails or screws used
to attach the wall to the studs. When you have found a screw you have found a stud. Studs are
usually 16" on center. Attach a Clip (T1) to each wall stud with #8 x 2" Black Screws (T3). See
Figure 10a.
The clips attached to the furniture must penetrate solid wood such as the back apron or a leg.
Do not attach where it will be screwed only into the thin back panel. Attach the second clip from
each kit to the unit with #6 x 5/8" Philtruss Screws (T5). See Figure 10b. Connect the two clips
with the Nylon Zip-Tie (T2). Pull the Nylon Zip-Tie (T2) tight so there is no slack. See
Figures 10c and 10d. We have included an extra Nylon Zip-Tie in each kit; if you should need to
move your furniture cut the Zip-Ties that you are using and replace with the extra Zip-Ties when
the furniture is back in place.
The screws attaching your furniture to the wall must be inserted
into a wall stud. Do not attempt to use wall anchors.
Pull tight
Wood
Stud
Fig. 10c
Pull the Nylon Zip-Tie (T2)
tight so there is no slack.
T1
T2
T5
T3
(Side view)
Fig. 10a
T1
T3
T5
Top
Fig. 10b
Fig. 10d
Wood
Stud
Back