Whittier Wood Furniture Addison 1242DUET User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 02/18
Model #
1242DUET
Addison
Upholstered
Bench
Duet = Natural finish
Assembly Instructions
IMPORTANT NOTES:
•For normal household use only. Not recommended for commercial use.
•Do not climb or stand on or in this piece of furniture.
•This assembly requires two people.
WARNING
Drilling, sawing, sanding or machining wood products can expose you to
wood dust, a substance known to the state of California to cause cancer.
Avoid inhaling wood dust or use a dust mask or other safeguards for
personal protection.
For more information go to: www.p65warnings.ca.gov/wood
This product can expose you to chemicals, including formaldehyde,
which are known to the State of California to cause cancer.
For more information go to: www.p65warnings.ca.gov/furniture
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CUSTOMER SERVICE
If you ever have questions about your furniture, please do not hesitate to contact us. In the unlikely event you need a
replacement part; we can make those parts available through an authorized Whittier Wood Furniture dealer. If you
cannot order replacement parts through your dealer, please contact our customer service department.
Hours: Our friendly customer service staff can be reached:
Monday-Friday 8:00 a.m. to 5:00 p.m. (Pacific Time).
You may leave a message 24 hours a day, seven days a week.
Customer Service: 800-653-3336 • Outside the U.S.: 541-687-0213
Fax: [phone]• Email: [email protected]
Thank you for allowing us to help you furnish your
home. We are certain you will be delighted with
your new furniture for many years to come.

1242DUET Addison Upholstered Bench
Parts List
1242DUET — Page 2 — 02/18
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter(s) and part name.
Part
Description
Quantity
A
Upholstered Seat
1
B
Leg Frame Assembly
2
C
Side Apron Assembly
2
D
Center Seat Support
1
E
#8 x 1-3/4" Pan Head Screw
29
(16 inserted)
F
5/16" Flat Washer
8
G
3/8" x 1" Insert Nut (inserted)
8
H
3/8" x 2-1/2" Hex Bolt
8
I
1/4" x 20mm Insert Nut (inserted)
4
J
1/2" x 2-1/4" Wood Dowel (inserted)
4
K
3/8" x 1-1/2" Wood Dowel (inserted)
2
L
Adjustable Glide (installed in Legs)
4

1242DUET Addison Upholstered Bench
Assembly Instructions
1242DUET — Page 3 — 02/18
Tools Required: Phillips Screwdriver, 9/16" or Adjustable Wrench, Mallet or Padded Hammer.
1. Lay one Leg Frame Assembly (B) face down on a clean, protected surface. Insert the Apron
Assemblies (C) using the dowel and dowel hole in the Frame Assembly for alignment. Secure
with 3/8" X 2-1/2" Hex Bolts (H) and 5/16" Washers (F). See Figures 1 and 1a.
2. Insert the Center Seat Support (D) using the dowel and the dowel hole at the center of the Side
Frame Assembly (B) as shown in Figure 2a. Secure with a #8 X 1-3/4" Pan Head Screw (E).
See Figures 2 and 2a.
Fig. 2
D
B
E
Fig. 2a
E
x 1
D
E
B
F
Fig. 1a
F
H
x 4
x 4
C
B
Fig. 1
H
C

1242DUET Addison Upholstered Bench
Assembly Instructions
1242DUET — Page 4 — 02/18
3. Lay the remaining Leg Frame Assembly (B) face down on a clean, protected surface. Flip the
assembled pieces from step 2 over and align the dowels in that assembly to the dowel holes in
the Leg Frame Assembly as shown in Figure 3. Insert the dowels into the holes and secure
using 3/8" X 2-1/2" Hex Bolts (H) with 5/16" Washers (F) and #8 X 1-3/4" Pan Head Screw (E).
See Figure 3.
4. Using the pocket holes as guides, secure the Leg Frame Assembly to the Upholstered Seat (A)
with eleven #8 x 1-3/4" Pan Head Screws (E). See Figure 4.
Fig. 4
A
E
E
x 11
Fig. 3
B
F
H
x 4
x 4
E
x 1
C
C
D
E
F
H

1242DUET Addison Upholstered Bench
Assembly Instructions
1242DUET — Page 5 — 02/18
5. Turn the bench upright.
Place the bench at its final destination. Rotate the Adjustable Glides (L) on the bottoms of the
legs until the unit is level. See Figure 5.
Fig. 5
L
L