Whittier Wood Furniture McKenzie 2068AFGACf User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 09/13
McKenzie Media
Consoles
AFGAC = Glazed Antique Cherry finish
AFCAF = Caffè finish
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended for commercial use.
Do not climb, sit or stand on this piece of furniture.
Do not overload the drawers or shelves.
Unload items before you move this unit.
Before you load or move this unit, tighten all screws and supports.
Handle the glass plates with care. Glass is fragile.
Before you begin your project, completely read the Assembly
Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement
floor).
Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
This assembly requires two people.
WARNING
Serious or fatal crushing injuries can occur from furniture tip-over. Use of
tip-over restraints may only reduce but not eliminate the risk of tip-over.
To help prevent tip-over:
Place heaviest items in the bottom drawers.
Unless specifically designed to accommodate, do not set TVs or other
heavy objects on top of this product.
Never allow children to climb or hang on drawers, doors or shelves.
Never open more than one drawer at a time.
Warning: At least one tipping restraint kit was included with your piece of
Whittier Wood Furniture. When you receive your furniture, be sure to find
and properly install the tipping restraint(s). If you cannot locate the
restraint(s), please contact us immediately for replacement.
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Model #
2068AFGACf;
2068AFCAFf
54"W McKenzie
Media Console
Model #
2069AFGACf;
2069AFCAFf
64"W McKenzie
Media Console

2068AFGACf; 2068AFCAFf 54"W McKenzie Media Console &
2069AFGACf; 2069AFCAFf 64"W McKenzie Media Console
Parts List
2068AFGACf_2068AFCAFf_2069AFGACf_2069AFCAFf —Page 2 —09/13
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
2068AFGACf
2068AFCAFf
2069AFGACf
2069AFCAFf
A
Top Assembly
1
1
Bb
Adjustable Shelf
2
2
C
Knob (attached)
7
7
D
#8 x 1-1/2" Machine Screw (installed)
7
7
E
Drawer Face (installed)
6
6
F
Drawer Box (inserted)
6
6
G
Drawer Slides (pre-installed sets)
6
6
Ha
Door Frame
1
1
Ia
Door Glass (attached)
1
1
Jd
Case
1
1
L
Shelf Bracket (installed)
8
8
M
#6 x 1/2" Undercut Screw (inserted)
8
8
Nb
Removable Back (attached)
2
2
O
Door Glass Support Rail (attached)
2
2
P
Door Glass Support Stile (attached)
2
2
Q
#6 x 3/4" Flat Head Screw (inserted)
12
12
S
#6 x 5/8" Philtruss Screw (inserted)
16
16
U
Hinge (attached)
2
2
X
Small Adjustable Glide (installed)
4
4
Y
#8 x 7/8" Lo-Profile Screw (inserted)
24
24
ZA
#8 x 1" Pan Head Screw (inserted)
4
4
ZB
#8 x 1-1/4" Pan Head Screw (inserted)
14
16
ZD
#8 x 1-1/4" Black Screw (inserted)
5
6

2068AFGACf; 2068AFCAFf 54"W McKenzie Media Console &
2069AFGACf; 2069AFCAFf 64"W McKenzie Media Console
Parts List
2068AFGACf_2068AFCAFf_2069AFGACf_2069AFCAFf —Page 3 —09/13
Part
Description
Quantity
2068AFGACf
2068AFCAFf
2069AFGACf
2069AFCAFf
ZG
Drawer Stop (attached)
4
4
ZH
Turn Button (attached)
4
4
ZI
#6 x 5/8" Undercut Screw ZN (inserted)
0 (AFGAC)
12 (AFCAF)
0 (AFGAC)
12 (AFCAF)
ZJ
#6 x 1/2" Philtruss Screw (inserted)
36
36
ZK
#6 x 3/4" Philtruss Screw (inserted)
36
36
ZS
Insert Nut (inserted)
4
4
ZT
#8 x 1-3/8" Lo-Profile Screw (inserted)
6
6
ZU
#8 x 20mm Pan Head Screw (inserted)
4
4
ZV
Foot Bracket (attached)
1
1
ZW
Adjustable Glide (installed)
1
1
ZX
Tuscan Magnetic Lock & Plate
(pre-installed sets)
2
2
ZY
#6 x 5/8" Undercut Screw AB (inserted)
16 (AFGAC)
4 (AFCAF)
16 (AFGAC)
4 (AFCAF)
TS
Media Tipping Restraint (attached)
1 set
1 set
2068 shown in the illustrations.

2068AFGACf; 2068AFCAFf 54"W McKenzie Media Console &
2069AFGACf; 2069AFCAFf 64"W McKenzie Media Console
Assembly Instructions
2068AFGACf_2068AFCAFf_2069AFGACf_2069AFCAFf —Page 4 —09/13
Tool Required: Phillips Screwdriver, Pencil.
1. Place the console at its final destination. Rotate the Adjustable Glides (X) found at the corners
of the unit and (ZW) at the bottom of the Center Foot until the unit is level. See Figure 1.
2. You may want to remove the Removable Backs (Nb) so that you can fit your media units into the
console more easily. To do so, unlock the Turn Button (ZH) as shown in Figures 2 and 2b. Slide
the backs away and place them off to the side. To put them back into place, slide the backs
behind the Drawer Stops (ZG) and position the Turn Button so that it is locked. See Figures 2a
and 2b.
ZG
ZH
Locked
Position
Fig. 2
Fig. 2b
Fig. 2a
Nb
Nb
ZH
ZG
Unlocked
Position
Fig. 1
ZW
X
X

2068AFGACf; 2068AFCAFf 54"W McKenzie Media Console &
2069AFGACf; 2069AFCAFf 64"W McKenzie Media Console
Assembly Instructions
2068AFGACf_2068AFCAFf_2069AFGACf_2069AFCAFf —Page 5 —09/13
3. To move the Adjustable Shelves (Bb), remove the #6 x 1/2" Undercut Screws (M) and the
Shelves (Bb). Reposition the Shelf Brackets (L) to the desired positions, replace the shelf and
insert the screws. See Figures 3 and 3a.
Continued on Page 6
Fig. 3
M
L
Fig. 3a
Bb
Door removed for illustration purposes.

2068AFGACf; 2068AFCAFf 54"W McKenzie Media Console &
2069AFGACf; 2069AFCAFf 64"W McKenzie Media Console
Assembly Instructions
2068AFGACf_2068AFCAFf_2069AFGACf_2069AFCAFf —Page 6 —09/13
Furniture Tipping Restraint Instructions
Before you begin this assembly, identify each part and make sure the quantities received match what is on this
list. If you need to replace a part, contact Whittier Wood Furniture customer service and refer to the following
list for its name and letter code.
Part
Description
Quantity
A
Cam Buckle and Short Strap (installed)
1
B
Plastic Bracket (installed)
1
C
1" x 1000mm Long Strap (installed)
1
D
#8 x 3" Pan Head Screw
2
E
#10 x 1" Oval Head Screw (inserted)
1
F
Washer
1
If you have a stone or tile floor or do not wish to drive screws into the corner of the baseboard
and floor see the instruction included inside the tipping restraint kit for an alternate
installation.
4. Decide where you want to place the piece of furniture in your room. Mark the baseboard with a
pencil mark directly behind the location where the tipping restraint is attached to your item.
Move the item away from the wall far enough to allow you to access the spot where the
baseboard meets the floor. Position the straps and Plastic Bracket (B) as shown in Figures 4
and 4a with the angled corners of the Plastic Bracket (B) firmly placed against the seam of the
baseboard and floor. Attach by driving #8 x 3" Pan Head Screws (D) through the holes in the
Plastic Bracket (B) into the seam below the baseboard where it meets the floor. See Figures 4
and 4a.
Fig. 4
Fig. 4a
Wall
Floor
D
Floor
Baseboard
D
x 2

2068AFGACf; 2068AFCAFf 54"W McKenzie Media Console &
2069AFGACf; 2069AFCAFf 64"W McKenzie Media Console
Assembly Instructions
2068AFGACf_2068AFCAFf_2069AFGACf_2069AFCAFf —Page 7 —09/13
5. Move the item back into position against the wall and reach underneath the piece of furniture to
grasp the loop in the free end of the strap. Pull the free end of the strap until portion between
the Cam Buckle (A) and the back apron of the item is tight. See Figures 5 and 5a. If you need
to move the piece of furniture reach beneath and locate the buckle which connects the two
sections of the strap and depress the release lever, then pull on the section of strap that is
between the buckle and the back apron of the furniture until there is enough slack to allow you
to pull the item away from the wall.
Fig. 5a
Fig. 5
C
Wall
Floor