Whittier Wood Furniture McKenzie 1382GACh User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 03/20
Model #
1382GACh
1382CAFh
McKenzie Cal-King
Bookcase
Headboard
GAC = Glazed Antique Cherry finish
CAF = Caffè finish
Assembly Instructions
IMPORTANT NOTES:
•For normal household use only. Not recommended for commercial use.
•Unload items before you move this unit.
•Do not overload the concealed storage areas.
•Do not overload the cubbies.
•This assembly requires two people.
WARNING
Drilling, sawing, sanding or machining wood products can expose you to
wood dust, a substance known to the state of California to cause cancer.
Avoid inhaling wood dust or use a dust mask or other safeguards for
personal protection.
For more information go to: www.p65warnings.ca.gov/wood
This product can expose you to chemicals, including formaldehyde,
which are known to the State of California to cause cancer.
For more information go to: www.p65warnings.ca.gov/furniture
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CUSTOMER SERVICE
If you ever have questions about your furniture, please do not hesitate to contact us. In the unlikely event you need a
replacement part; we can make those parts available through an authorized Whittier Wood Furniture dealer. If you
cannot order replacement parts through your dealer, please contact our customer service department.
Hours: Our friendly customer service staff can be reached:
Monday-Friday 8:00 a.m. to 5:00 p.m. (Pacific Time).
You may leave a message 24 hours a day, seven days a week.
Customer Service: 800-653-3336 • Outside the U.S.: 541-687-0213
Fax: [phone]• Email: [email protected]
Thank you for allowing us to help you furnish your
home. We are certain you will be delighted with
your new furniture for many years to come.

1382GACh 1382CAFh McKenzie Cal-King Bookcase Headboard
Parts List
1382GACh_1382CAFh — Page 2 — 03/20
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
Ah
Headboard Assembly
1
E
#8 x 1-1/4" Black Screw (inserted)
12
R
Assembled Door (attached)
2
Sg
False Bottom
4
XA
Top Assembly (attached)
1
XB
Power Bar and USB (installed)
1
YA
Large Adjustable Glide (installed)
2
YB
#8 x 5/8" Pan Head Screw (inserted)
8
YG
#14 x 1-1/4" Pan Head Screw
6
YJ
#8 x 1-3/8" Lo-Profile Screw (inserted)
14
YL
#8 x 7/8" Black Lo-Profile Screw (inserted)
4
YR
#8 Washer (inserted)
1
YS
Wood Dowel (inserted)
2
YT
1/4" x 1-1/2" Hex Bolt (inserted)
6
ZA
Hinge (installed)
6
ZB
Magnetic Plate (installed)
4
ZC
Magnetic Catch (installed)
4
ZE
Door Stay (attached)
2
ZF
#6 x 5/8" Undercut Screw ZN (inserted)
8
ZG
Door Stay Support (attached)
2
ZH
#6 x 1-1/4" Black Pan Head Screw (inserted)
6
ZI
#6 x 5/8" Undercut Screw AB (inserted)
44
ZJ
#6 x 5/8" Philtruss Screw (inserted)
17
ZK
18mm Washer
12
(6 inserted)

1382GACh 1382CAFh McKenzie Cal-King Bookcase Headboard
Parts List
1382GACh_1382CAFh — Page 3 — 03/20
Part
Description
Quantity
ZO
#8 x 2-1/4" Black Screw (inserted)
6
ZP
#8 x 1" Black Screw (inserted)
16
ZQ
Left Bracket (attached)
2
ZR
Right Bracket (attached)
2
ZS
Wire Clip Screw (attached)
8
ZT
Tack Glide (attached)
4
ZU
1/4" T-Nut (inserted)
6
ZZ
Corner Brace (attached)
2

1382GACh 1382CAFh McKenzie Cal-King Bookcase Headboard
Assembly Instructions
1382GACh_1382CAFh — Page 4 — 03/20
Tools Required: Drill, 1/8" bit, Phillips Screwdriver, Slotted Screwdriver.
Optional: 7/16" open end or box end wrench.
NOTE: Use this instruction and hardware kit included with this 1382 McKenzie Cal-King
Bookcase Headboard ONLY if you are using a Hollywood frame.
IF you are using this product with Whittier Wood Furniture Footboard and Pedestal kits,
disregard this instruction and hardware and use what is included with your Footboard kit.
Note: Assembly can be separated into three pieces for ease of maneuvering through narrow
halls and stairways; if you need to perform this process see steps 7 through 11.
1. Remove the metal brackets attached to the Headboard (Ah).
2. Place the Headboard (Ah) against the end brackets of the frame and mark the locations for the
screws. Drill pilot holes approximately 1-1/4" deep. To make sure you don’t drill deeper,
measure 1-1/4" up from the end of the drill bit and wrap a piece of tape around the bit. Stop
drilling when the edge of the tape meets the wood.
3. Position the Headboard (Ah) against the frame and attach using six #14 x 1-1/4" Pan Head
Screws (YG) and six Washers (ZK).
4. Place your bed in its final position. To level the headboard, reach behind the bookcase front legs
and, using a slotted screwdriver, find the Large Adjustable Glide (YA). Using a slotted screw
driver, rotate the Large Adjustable Glides (YA) clockwise until they bear weight.
See Figures 4, 4a and 4b.
This is important if the bookcase headboard sits upon a carpet tack strip.
Fig. 4
Fig. 4a
Fig. 4b
The top of the Large
Adjustable Glide (YA)
is slotted.
YA
ZZ
Hollywood bed frame
removed for illustration
purposes.

1382GACh 1382CAFh McKenzie Cal-King Bookcase Headboard
Assembly Instructions
1382GACh_1382CAFh — Page 5 — 03/20
5. Open the Door (R). To adjust the brake tension on the Door Stay (ZE) turn the screw on the
front of the Door Stay clockwise to loosen or counterclockwise to tighten. See Figures 5 and 5a.
6. Unwrap the False Bottoms (Sg) and place them on top of the rails in the Headboard Assembly
(Ah). Make sure the finger holes face forward as shown in Figure 6. After you have placed your
electronics inside the cubbies, use the Wire Clips (ZS) on the underside of the cubbies to secure
the wires. Close the door tightly making sure the magnetic catches and plates securely touch.
Fig. 6
Ah
R
Sg
Sg
Sg
Sg
ZE
L
o
o
s
e
n
T
i
g
h
t e
n
Fig. 5a
Fig. 5
ZG

1382GACh 1382CAFh McKenzie Cal-King Bookcase Headboard
Assembly Instructions
1382GACh_1382CAFh — Page 6 — 03/20
7. To divide this larger unit into three sub-assemblies, start by removing the Top Assembly (XA).
Remove the #6 x 5/8" Philtruss Screw (ZJ) and #8 Washer (YR) connecting the Backs to the
Vertical Divider, and the #6 x 5/8" Philtruss Screws (ZJ) connecting the backs to the Top
Assembly. Do not remove the Backs. See Figures 7 and 7a.
8. Figure 8 shows the locations of the screws that need to be removed. You can access these from
the front of the unit. Remove the #8 x 1-3/8" Lo-Profile Screws (YJ) attaching the Sides, Vertical
Dividers and Blocks to the Top. Carefully remove the Top Assembly (XA) from the Case. See
Figures 8 and 8a.
Fig. 8
YJ
x 14
YJ
Backs removed for illustration purposes only.
Fig. 8a
XA
Fig. 7
Fig. 7a
YR
x 1
ZJ
x 11
YR
ZJ

1382GACh 1382CAFh McKenzie Cal-King Bookcase Headboard
Assembly Instructions
1382GACh_1382CAFh — Page 7 — 03/20
9. Open the Doors and remove the 1/4" x 1-1/2" Hex Bolts (YT) and 18mm Washers (ZK). See
Figures 9 and 9a.
10. Carefully separate the two halves of the Case Assembly. See Figures 10 and 10a.
11. After moving the headboard sections into your room reassemble the Headboard by reversing
these steps.
Fig. 10
Fig. 10a
Fig. 9
ZK
YT
Fig. 9a
ZK
x 6
YT
x 6