Whittier Wood Furniture McKenzie Queen 1316AFGACa User manual

P.O. Box 2827
Eugene, OR 97402 USA
Outside U.S. or Canada: 541- 687- 0213Outside U.S. or Canada: 541- 687- 0213
800-653-3336800-653-3336
Fax: [phone] • Fax: [phone] • wwwwww.whittie.whittierrwood.comwood.com
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.AMail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A
For normal household use only.
recommended for commercial use.
Congratulations!
Production Code:
Assembly Instructions
McKenzie
Queen Storage Bed
1316AFGACa
Glazed Antique
Cherry Finish
VN
Service Policy: We will replace parts
which are defective, missing or damaged.
Please contact Whittier Wood Products
customer service department directly (by
phone, fax, mail or E-mail) for replacement
parts.
Hours: Our friendly customer service staff
can be reached Monday-Friday 7:00 a.m. to
5:00 p.m. (Pacific Time). A message can be
left 24 hours a day, 7 days a week.
To Order: Provide the complete furniture
model number, part letter, production code,
quantity needed, reason for replacement
and your full name and address along with
a telephone number in case we need to
contact you.
Parts ship from our Eugene, Oregon factory
within 1 or 2 business days from the time
we receive the request. Please allow 5-10
business days for delivery.
This fine piece of furniture will make a handsome
addition to your home. For the best results, start
by reading the Assembly Instructions before you begin
your project.
Unload items from this unit prior to moving.
Before loading or moving this unit, check all screws
and supports for tightness.
Store the item: 1) in the box; 2) in a dry place; 3) in
temperatures ranging from 40° to 90°. (Not on a cold,
possibly damp, cement floor.)
Inspect your furniture periodically for any loose glue
joints or screws, or any other problem which may be
affecting the stability of your furniture. Tighten or repair
as needed.
This Assembly requires two people.
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
05/21/08

1316AFGACa McKenzie Queen Storage Bed — Parts List
1319AFGACa (x1)
1318AFGACa (x2)
To replace a part, please refer to the following list for its letter and name.
Page 2 — 1316AFGACa — 05/21/08
F — ¼" x 1¾" Hex Bolt
— Qty. 16
G — ¼" x 2½" Hex Bolt
— Qty. 16
E — #8 x 1¼" Black Screw — Qty. 24
H — Washer — Qty. 32
N — #8 x 1½" Machine Screw
— Qty. 3
O — Knob — Qty. 3
I — Pedestal Kit — Qty.1
A — Headboard — Qty.1
B — Footboard — Qty.1
C — Trestle Without T-Nuts — Qty.4
D — Trestle With T-Nuts — Qty.8
P — Deckboard — Qty.1
J — Small Drawer Box — Qty. 2
(pre-assembled)
K — Large Drawer Box — Qty. 1
(pre-assembled)
L — Small Drawer Face — Qty. 2
(pre-attached)
M — Large Drawer Face — Qty. 1
(pre-attached)
Q — Drawer Slides — Qty. 3
(pre-installed sets)
T — #8 x 2" Black Screw — Qt
U — Foot Assembly — Qty. 2
V — Leveler Bracket — Qty. 2
(pre-installed)
W — Adjustable Glide — Qty. 2
(pre-installed)
y. 6

1316AFGACa McKenzie Queen Storage Bed
Assembly Instructions
Page 3 — 1316AFGACa — 05/21/08
TOOLS REQUIRED:
This Assembly Requires Two People
Phillips Screwdriver, 7/16" wrench and tape measure.
Remove the Trestles from the back of the Headboard as seen in Fig. 1
and place them off to the side.
1.
Place both Pedestals (I) approximately 63" apart as shown in Fig. 2.2.
Fig. 1
Fig. 2
Shipping Straps
I
I
63"

Page 4 — 1316AFGACa — 05/21/08
Remove Drawers (J & K) from Pedestal Kits (I). To remove drawers, push up on
the left side of the Drawer Release Lever while pushing down on the right Drawer
Release Lever (see Fig. 3b). Note where each drawer came from to ensure correct
re-installation. (Positions are marked on drawer backs.)
3.
Fig. 3
Fig. 3b
Drawer Release Lever
Place 4
NOTE: DO NOT TIGHTEN BOLTS UNTIL FINAL ASSEMBLY
IN STEP 10 IS COMPLETED.
Trestles with with T-Nuts (D) between Pedestals (I) and insert 1¾" bolt
(F) and washer (H) as shown in Fig. 4b. When installing Trestles (D), make sure
the T-nuts face out as shown in Fig. 4.
4.
Fig. 4b
Trestle with T-Nuts (D)
F x 16 H x 16
H
F
Fig. 4
T-Nuts face out
D
D
D
D
I
I

Fig. 5
5. Rotate Pedestal Assembly upside down so that the plywood Deckboards are
on the floor.
Fig. 6b
G x 16 H x 16
Fig. 6
D
D
D
D
C
CC
C
6. Place the remaining Trestles (C and D) on the Pedestal Assembly. Face the Trestles
with T-Nuts (D) toward the ends of the Assembly from the center as shown in Fig 6.
Insert 2½" Hex Bolt (G) and Washer (H). See Fig. 6b. DO NOT TIGHTEN BOLTS
UNTIL FINAL ASSEMBLY IN STEP 10.
R
o
t
a
t
e
P
e
d
e
s
t
a
l
A
s
s
e
m
b
l
y
u
p
s
i
d
e
d
o
w
n
s
o
t
h
a
t
t
h
e
p
l
y
w
o
o
d
D
e
c
k
b
o
a
r
d
s
a
r
e
o
n
t
h
e
f
l
o
o
r
.
Page 5 — 1316AFGACa — 05/21/08

Rotate Pedestal Assembly to its original position.
Page 6 — 1316AFGACa — 05/21/08
Fig. 8
Fig. 7
Fig. 7b
D
D
CC
T x 6
7.
8.
On each inner Pair of Trestles (C & D), place a Foot Assembly (U) between
the two middle trestles as shown in Fig. 7. Insert three #8 X 2" Black screws (T)
as shown in Fig. 7b.
U
V
W
T
R
o
t
a
t
e
P
e
d
e
s
t
a
l
A
s
s
e
m
b
l
y
t
o
i
t
s
o
r
i
g
i
n
a
l
p
o
s
i
t
i
o
n
.

Attach Headboard (A) to Pedestal Assembly as in previous step.
NOTE: NOW TIGHTEN ALL BOLTS ON TRESTLES.
10.
Fig. 10 A
Stand the Footboard (B) at one end of the Pedestal Assembly as in Fig. 9. Align
brackets as shown in Fig. 9b, and slide the Pedestal Assembly down on to
the Footboard (B).
9.
Fig. 9b
Fig. 9
B
Page 7 — 1316AFGACa — 05/21/08
Adjust Glides (W) on the Foot Assemblies (U) so the Glides just touch the floor. 11.
Fig. 11
Adjustable Glide (W)
Leveler Bracket (V)
B

Page 8 — 1316AFGACa — 05/21/08
Place Deckboards (P) as shown in Fig. 12. There should be a small gap between
each deckboard. Secure with #8x1¼" Screw (E).
12.
Fig. 12
E x 24
P
Carefully align drawer slides into the cabinet and gently push the drawers back
to their original positions. Sleep well, and enjoy!
13.